With the roof panel No.1 assembly removed.
REMOVAL
| Symbol Meaning | |
|---|---|
|
Remove Weld Points |
|
Cut Location for Supply Parts |
| *A | for 5 Door | - | - |
| *A | for 4 Door LHD | *B | for Type A |
| *A | for 4 Door LHD | *B | for Type B |
| *A | for 4 Door RHD | *B | for Type A |
| *A | for 4 Door RHD | *B | for Type B |
INSTALLATION
| Symbol Meaning | |
|---|---|
|
Plug Weld |
|
Butt Weld |
|
Body Sealer |
Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.
Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)
Before temporarily installing the new parts, apply body sealer to the roof panel reinforcement sub-assembly No.2 and roof panel reinforcement sub-assembly No.3.
Apply enough body sealer to the panels.
| *1 | ROOF PANEL REINFORCEMENT SUB-ASSEMBLY NO.2 | *2 | ROOF PANEL REINFORCEMENT SUB-ASSEMBLY NO.3 |
Before temporarily installing the new parts, weld the roof panel rear No.1, roof panel reinforcement sub-assembly No.2, roof panel reinforcement sub-assembly No.3 and roof panel reinforce stiffener No.2 with the standard number of welding points.
| *A | w/o ROOF PANEL REINFORCE STIFFENER NO.2 | - | - |
| *1 | ROOF PANEL REAR NO.1 | *2 | ROOF PANEL REINFORCEMENT SUB-ASSEMBLY NO.2 |
| *3 | ROOF PANEL REINFORCEMENT SUB-ASSEMBLY NO.3 | - | - |
| *A | w/ ROOF PANEL REINFORCE STIFFENER NO.2 | - | - |
| *1 | ROOF PANEL REAR NO.1 | *2 | ROOF PANEL REINFORCEMENT SUB-ASSEMBLY NO.2 |
| *3 | ROOF PANEL REINFORCEMENT SUB-ASSEMBLY NO.3 | *4 | ROOF PANEL REINFORCE STIFFENER NO.2 |
Before temporarily installing the new parts, apply body sealer to the roof panel reinforcement No.1.
Apply enough body sealer to the panels.
| *1 | ROOF PANEL REINFORCEMENT NO.1 | - | - |
Weld the roof panel rear No.1 to the vehicle side.
| *A | for 5 Door | - | - |
| *1 | ROOF PANEL REAR NO.1 | - | - |
| *A | for 4 Door LHD | *B | for Type A |
| *1 | ROOF PANEL FRONT | - | - |
| *A | for 4 Door LHD | *B | for Type B |
| *1 | ROOF PANEL FRONT | - | - |
| *A | for 4 Door RHD | *B | for Type A |
| *1 | ROOF PANEL FRONT | - | - |
| *A | for 4 Door RHD | *B | for Type B |
| *1 | ROOF PANEL FRONT | - | - |
After welding, apply body sealer to the corresponding parts. (See the painting/coating)
After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 750 mm (29.53 in.) | B | 932 mm (36.69 in.) |
| C | 1182 mm (46.54 in.) | D | 905 mm (35.63 in.) |
| E | 1193 mm (46.97 in.) | F | 404 mm (15.91 in.) |
| G | 751 mm (29.57 in.) | H | 398 mm (15.67 in.) |
| I | 755 mm (29.72 in.) | - | - |