REMOVAL
| Symbol Meaning | |
|---|---|
|
Remove Weld Points |
|
Cut Location for Supply Parts |
| *A | for 5 Door | - | - |
| *A | for 4 Door LHD | *B | w/o Roof Window Glass |
| *C | for Type A | - | - |
| *A | for 4 Door LHD | *B | w/o Roof Window Glass |
| *C | for Type B | - | - |
| *A | for 4 Door RHD | *B | w/o Roof Window Glass |
| *C | for Type A | - | - |
| *A | for 4 Door RHD | *B | w/o Roof Window Glass |
| *C | for Type B | - | - |
| *A | for LHD | *B | w/ Roof Window Glass |
| *A | for RHD | *B | w/ Roof Window Glass |
INSTALLATION
| Symbol Meaning | |
|---|---|
|
Plug Weld |
|
Butt Weld |
|
Body Sealer |
Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.
Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)
Before temporarily installing the new parts, apply body sealer to the roof panel reinforcement sub-assembly No.4.
Apply enough body sealer to the panels.
| *1 | ROOF PANEL REINFORCEMENT SUB-ASSEMBLY NO.4 | - | - |
Before temporarily installing the new parts, weld the roof panel rear No.2, roof panel reinforcement sub-assembly No.4 and roof frame sub-assembly with the standard number of welding points.
| *A | w/o Roof Window Glass | - | - |
| *1 | ROOF PANEL REAR NO.2 | *2 | ROOF PANEL REINFORCEMENT SUB-ASSEMBLY NO.4 |
| *A | w/ Roof Window Glass | - | - |
| *1 | ROOF PANEL REAR NO.2 | *2 | ROOF PANEL REINFORCEMENT SUB-ASSEMBLY NO.4 |
| *3 | ROOF FRAME SUB-ASSEMBLY | - | - |
Before temporarily installing the new parts, apply body sealer to the roof panel reinforcement No.5 and roof panel reinforcement No.6.
Apply enough body sealer to the panels.
| *A | w/o Roof Window Glass | - | - |
| *1 | ROOF PANEL REINFORCEMENT NO.5 | *2 | ROOF PANEL REINFORCEMENT NO.6 |
Weld the roof panel rear No.2 to the vehicle side.
| *A | for 5 Door | - | - |
| *1 | ROOF PANEL REAR NO.2 | - | - |
| *A | for 4 Door LHD | *B | w/o Roof Window Glass |
| *C | for Type A | - | - |
| *1 | ROOF PANEL REAR NO.2 | - | - |
| *A | for 4 Door LHD | *B | w/o Roof Window Glass |
| *C | for Type B | - | - |
| *1 | ROOF PANEL REAR NO.2 | - | - |
| *A | for 4 Door RHD | *B | w/o Roof Window Glass |
| *C | for Type A | - | - |
| *1 | ROOF PANEL REAR NO.2 | - | - |
| *A | for 4 Door RHD | *B | w/o Roof Window Glass |
| *C | for Type B | - | - |
| *1 | ROOF PANEL REAR NO.2 | - | - |
| *A | for LHD | *B | w/ Roof Window Glass |
| *1 | ROOF PANEL REAR NO.2 | - | - |
|
N*m (kgf*cm, ft.*lbf) : Specified torque | - | - |
| *A | for RHD | *B | w/ Roof Window Glass |
| *1 | ROOF PANEL REAR NO.2 | - | - |
|
N*m (kgf*cm, ft.*lbf) : Specified torque | - | - |
After welding, apply body sealer to the corresponding parts. (See the painting/coating)
After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.
| *A | w/o Roof Window Glass | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 1154 mm (45.43 in.) | B | 1094 mm (43.07 in.) |
| C | 257 mm (10.12 in.) | D | 212 mm (8.35 in.) |
| *A | w/ Roof Window Glass | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 1154 mm (45.43 in.) | B | 1094 mm (43.07 in.) |
| C | 257 mm (10.12 in.) | D | 212 mm (8.35 in.) |
| E | 1230 mm (48.43 in.) | F | 1381 mm (54.37 in.) |
| G | 277 mm (10.91 in.) | H | 668 mm (26.30 in.) |