Home › Vehicle Exterior › BODY PANEL › FRONT BODY PILLAR (for High Roof)
BM35X0E _01 Vehicle Exterior _080418 BODY PANEL _0391625 FRONT BODY PILLAR(for High Roof) F

BODY PANEL  FRONT BODY PILLAR(for High Roof)  CUT AND JOIN REPLACEMENT SECTIONS (PATTERN 1)  


K151885

With the cowl top side panel assembly removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108827

Cut and Join Location

a.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)


b.

Remove the front side panel outer.

K151234C01
2.333,5.083 2.5,5.083 2.5,5.083 2.573,4.219 false 2.156,5.01 2.469,5.167 0.313,0.156 10 false *1 2.708,1.719 3.021,1.875 0.313,0.156 10 false *a 4.76,4.583 5.073,4.74 0.313,0.156 10 false *b
*1 FRONT SIDE PANEL OUTER - -
*a 340 mm (13.39 in.) *b 205 mm (8.07 in.)


K151549


c.

Remove the front pillar reinforcement sub-assembly lower.

K151235C01
2.25,4.5 2.417,4.5 2.417,4.5 2.583,3.969 false 2.083,4.417 2.396,4.573 0.313,0.156 10 false *1 2.708,1.594 3.021,1.75 0.313,0.156 10 false *a
*1 FRONT PILLAR REINFORCEMENT SUB-ASSEMBLY LOWER - -
*a 420 mm (16.54 in.) - -



d.

When replace only the outer panel, please cut off a necessary range depending on a damage range.

i.

Carefully cut the outer panel so not to damage the reinforcement.


ii.

Make sure that butt welding does not heat-affect the reinforcement when welding the outer panel.




INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108831

Butt Weld
K108834

Body Sealer

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

Weld the front pillar reinforcement sub-assembly lower to the vehicle side.

K151237C01
2.333,4.583 2.5,4.583 2.5,4.583 2.594,3.948 false 2.156,4.5 2.469,4.656 0.313,0.156 10 false *1
*1 FRONT PILLAR REINFORCEMENT SUB-ASSEMBLY LOWER - -
*a Ultra High Strength Steel Welding Point - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 2 panels together including 980 MPa ultra high strength steel.

*a: Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




d.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K151236


e.

Weld the front side panel outer to the vehicle side.

K151238C01
2.333,5.083 2.5,5.083 2.5,5.083 2.583,4.24 false 2.156,5 2.469,5.156 0.313,0.156 10 false *1
*1 FRONT SIDE PANEL OUTER - -


Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

When welding 3 panels or more together including 980 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)

*a: Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding.Sufficient weld strength cannot be assured when using 100% CO2 shield gas.




f.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


g.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.