With the side panel RH cut and join replacement sections removed.
REMOVAL
| Symbol Meaning | |
|---|---|
|
Remove Weld Points |
|
Cut and Join Location |
Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)
Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.
In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.
| *A | LH | - | - |
|
Adhesive | - | - |
Remove the front side panel outer and rocker panel outer rear.
| *A | LH | *B | for High Roof |
| *1 | FRONT SIDE PANEL OUTER | *2 | ROCKER PANEL OUTER REAR |
| *a | 155 mm (6.10 in.) | *b | 35 mm (1.38 in.) |
| *c | 615 mm (24.21 in.) | - | - |
| *A | LH | - | - |
| *A | LH | - | - |
Remove the A.
A is reused.
| *A | LH | - | - |
| *a | 115 mm (4.53 in.) | - | - |
Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.
In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.
| *A | LH | ||
|
Adhesive | - | - |
Remove the center body pillar reinforce sub-assembly upper.
| *A | LH | - | - |
| *1 | CENTER BODY PILLAR REINFORCE SUB-ASSEMBLY UPPER | - | - |
Remove the center body pillar inner.
| *A | LH | - | - |
| *1 | CENTER BODY PILLAR INNER | - | - |
| *a | 170 mm (6.69 in.) | - | - |
Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.
In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.
| *A | RH | - | - |
|
Adhesive | - | - |
Remove the front side panel outer.
| *A | RH | - | - |
| *1 | FRONT SIDE PANEL OUTER | - | - |
| *a | 155 mm (6.10 in.) | *b | 35 mm (1.38 in.) |
| *A | RH | - | - |
| *A | RH | - | - |
Remove the A.
A is reused.
| *A | RH | - | - |
| *a | 115 mm (4.53 in.) | - | - |
Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.
In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.
| *A | RH | - | - |
|
Adhesive | - | - |
Remove the center body pillar reinforce sub-assembly upper.
| *A | RH | *B | for High Roof |
| *1 | CENTER BODY PILLAR REINFORCE SUB-ASSEMBLY UPPER | - | - |
| *A | RH | - | - |
Remove the center body pillar inner.
| *A | RH | - | - |
| *1 | CENTER BODY PILLAR INNER | - | - |
| *a | 30 mm (1.18 in.) | - | - |
INSTALLATION
| Symbol Meaning | |
|---|---|
|
Plug Weld |
|
Butt Weld |
Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.
Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)
Weld the center body pillar inner to the vehicle side.
| *A | LH | *B | w/ Assist Grip |
| *1 | CENTER BODY PILLAR INNER | *2 | PILLAR SEAT BELT ANCHOR |
| *3 | PILLAR ASSIST GRIP BRACKET LOWER | - | - |
Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).
Do not apply adhesive around the plug welding points.
Minimize squeeze out in plug welding areas.
| *A | LH | ||
|
Adhesive | - | - |
Weld the center body pillar reinforce sub-assembly upper to the vehicle side.
| *A | LH | - | - |
| *1 | CENTER BODY PILLAR REINFORCE SUB-ASSEMBLY UPPER | - | - |
Weld the A to the vehicle side.
| *A | LH | - | - |
Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).
Do not apply adhesive around the plug welding points.
Minimize squeeze out in plug welding areas.
| *A | LH | - | - |
|
Adhesive | - | - |
Weld the front side panel outer and rocker panel outer rear to the vehicle side.
| *A | LH | *B | for High Roof |
| *1 | FRONT SIDE PANEL OUTER | *2 | ROCKER PANEL OUTER REAR |
| *A | LH | - | - |
| *A | LH | - | - |
| *1 | FUEL FILLER OPENING LID ASSEMBLY | *2 | RIVETS |
Weld the center body pillar inner to the vehicle side.
| *A | RH | - | - |
| *1 | CENTER BODY PILLAR INNER | *2 | PILLAR SEAT BELT ANCHOR |
Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).
Do not apply adhesive around the plug welding points.
Minimize squeeze out in plug welding areas.
| *A | RH | - | - |
|
Adhesive | - | - |
Weld the center body pillar reinforce sub-assembly upper to the vehicle side.
| *A | RH | *B | for High Roof |
| *1 | CENTER BODY PILLAR REINFORCE SUB-ASSEMBLY UPPER | - | - |
| *A | RH | - | - |
Weld the A to the vehicle side.
| *A | RH | - | - |
Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).
Do not apply adhesive around the plug welding points.
Minimize squeeze out in plug welding areas.
| *A | RH | - | - |
|
Adhesive | - | - |
Weld the front side panel outer to the vehicle side.
| *A | RH | - | - |
| *1 | FRONT SIDE PANEL OUTER | - | - |
| *A | RH | - | - |
| *1 | NO.4 PILLAR PLATE OUTER | *2 | CENTER BODY PILLAR COVER BASE |
After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)
After welding, apply body sealer to the corresponding parts. (See the painting/coating)
After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.