Home › Vehicle Exterior › BODY PANEL › SIDE PANEL LH (for Standard Roof, Glass Model)
BM35X0E _01 Vehicle Exterior _080418 BODY PANEL _0392280 SIDE PANEL LH(for Standard Roof, Glass Model) F

BODY PANEL  SIDE PANEL LH(for Standard Roof, Glass Model)  CUT AND JOIN REPLACEMENT SECTIONS  


K151903

Quarter Panel Replacement Using Adhesive
1.

Cut the wheel arch portion.

2.

Heat the quarter panel adhesive area and remove the quarter panel.

HINT:

Using an industrial heater gun or gas burner, heat the quarter panel to 110 to 140°C. Make sure the quarter panel does not warp.


3.

Clean off any adhesive that remains on the vehicle.

HINT:
·

Using an industrial heater gun or gas burner, heat the adhesive to 110 to 140°C.

·

Using a scraper, scrape away the adhesive.

·

If adhesive remains, the strength of any subsequently applied adhesive will be weak.



4.

Using a disc sander or belt sander, scuff and sand any adhesive that remains on the vehicle.

HINT:

Scuff at a width of approximately 10 mm (0.39 in.) over the previous adhesive coating.


5.

Apply adhesive to the exposed metal areas on the vehicle. Using a spatula, spread the adhesive evenly.

6.

Apply adhesive to the vehicle again.

7.

Using #60-120 grit sandpaper, scuff the adhesive application area on the new quarter panel.

8.

Apply adhesive to the new quarter panel. Using a spatula, spread the adhesive evenly.

9.

Using a vise grip or the palms of your hands, press the quarter panel so that the thickness of the adhesive is even.

10.

Complete installation the new quarter panel.

11.

Dry the adhesive areas of the new quarter panel.

HINT:
·

With dryer or equivalent (60°C): 60 minutes (complete hardening: 90 minutes)

·

Ambient temperature (25°C): 12 hours (complete hardening: 24 hours)




REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108827

Cut and Join Location

a.

Remove the A.

HINT:

A is reused.


K151358C01
4.25,3.5 4.083,3.5 4.083,3.5 3.646,2.802 false 4.917,1.583 5.229,1.74 0.313,0.156 10 false *a 2.896,3.5 3.208,3.656 0.313,0.156 10 false *b 4.333,3.427 4.583,3.667 0.25,0.24 10 false A
*a 40 mm (1.57 in.) *b 135 mm (5.31 in.)



b.

Remove the A.

HINT:

A is reused.


K151359C01
0.167,0.167 7,3.667 6.833,3.5 2.083,2.167 2.917,0.667 2.917,0.667 3.083,0.667 false 5.604,2.146 6.417,0.667 6.417,0.667 6.583,0.667 false 3.583,3.667 3.583,0.167 false 0.271,0.25 0.583,0.406 0.313,0.156 10 false *A 3.667,0.25 3.979,0.406 0.313,0.156 10 false *B 1.896,3.438 2.208,3.594 0.313,0.156 10 false *a 5.427,3.438 5.74,3.594 0.313,0.156 10 false *a 6.667,0.594 6.979,0.75 0.313,0.156 10 false A 3.167,0.583 3.479,0.74 0.313,0.156 10 false A
*A for Type A *B for Type B
*a 205 mm (8.07 in.) - -


K151360C01
1.104,4.135 1.417,4.292 0.313,0.156 10 false *a 1.385,2.531 1.698,2.688 0.313,0.156 10 false *b 2.021,3.156 2.333,3.313 0.313,0.156 10 false *c
*a 40 mm (1.57 in.) *b 250 mm (9.84 in.)
*c 425 mm (16.73 in.) - -



c.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K151364C01
0,0 0,0 false
K108837

Adhesive - -


K151361C01
1.74,1.333 2.052,1.49 0.313,0.156 10 false *a 4.25,1.26 4.563,1.417 0.313,0.156 10 false *b 5.792,1.229 6.104,1.385 0.313,0.156 10 false *c
*a 275 mm (10.83 in.) *b 160 mm (6.30 in.)
*c 110 mm (4.33 in.) - -


K151560

K151362

K151363

K151787



INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108824

Plug Weld
K108831

Butt Weld

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

Remove A from the new parts.

HINT:

A is reused.


K151848C01
2,2.167 2.167,2.167 2.167,2.167 2.552,2.667 false 3.333,5.333 3.167,5.333 3.167,5.333 2.969,4.667 false 1.813,2.104 2.125,2.26 0.313,0.156 10 false *1 3.417,5.26 3.729,5.417 0.313,0.156 10 false A 2.521,4.979 2.833,5.135 0.313,0.156 10 false *a 2.802,3.323 3.115,3.479 0.313,0.156 10 false *b 3.458,3.99 3.771,4.146 0.313,0.156 10 false *c
*1 QUARTER PANEL - -
*a 40 mm (1.57 in.) *b 250 mm (9.84 in.)
*c 425 mm (16.73 in.) - -



d.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K151364C01
0,0 0,0 false
K108837

Adhesive - -



e.

Weld the quarter panel to the vehicle side.

K151371C01
3.948,3.76 4.417,4.604 4.417,4.604 4.583,4.604 false 4.635,4.51 4.948,4.667 0.313,0.156 10 false *1
*1 QUARTER PANEL - -


K151372

K151373

K151790


f.

Weld the A to the vehicle side.

K151374N01
1.313,3.563 0.854,4.094 0.854,4.094 0.688,4.094 false 0.552,4.01 0.708,4.208 0.156,0.198 10 false A


g.

Weld the A to the vehicle side.

K151375N01
3.542,2.813 3.75,3.5 3.75,3.5 3.917,3.5 false 4.01,3.427 4.167,3.625 0.156,0.198 10 false A


h.

Weld the A to the vehicle side.

K151376C01
0.167,0.167 7,3.667 6.833,3.5 2.083,2.167 2.917,0.667 2.917,0.667 3.083,0.667 false 5.604,2.146 6.417,0.667 6.417,0.667 6.583,0.667 false 3.583,3.667 3.583,0.167 false 0.271,0.25 0.583,0.406 0.313,0.156 10 false *A 3.667,0.25 3.979,0.406 0.313,0.156 10 false *B 6.667,0.594 6.979,0.75 0.313,0.156 10 false A 3.167,0.583 3.479,0.74 0.313,0.156 10 false A
*A for Type A *B for Type B



i.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)


j.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


k.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.