Home › Vehicle Exterior › BODY PANEL › FIT STANDARD / ADJUSTMENT METHOD › 2019.06–2020.05
BM35X0E _01 Vehicle Exterior _080418 BODY PANEL _0389984 FIT STANDARD / ADJUSTMENT METHOD F

BODY PANEL  FIT STANDARD / ADJUSTMENT METHOD  ADJUSTMENT  


INSPECT HOOD SUB-ASSEMBLY


a.

Check that the clearance measurements of areas A to H are within the standard ranges.

B537827N01
1.469,3.302 1.76,3.625 0.292,0.323 10 false A 1.573,0.844 1.865,1.167 0.292,0.323 10 false B 0.25,0.802 0.542,1.125 0.292,0.323 10 false C 3.479,0.625 3.771,0.948 0.292,0.323 10 false D 4.802,0.708 5.094,1.031 0.292,0.323 10 false E 4.813,0.292 5.104,0.615 0.292,0.323 10 false F 6.479,0.365 6.792,0.604 0.313,0.24 10 false G 6.01,0.75 6.323,0.99 0.313,0.24 10 false H

Standard Clearance:
Area Measurement Area Measurement
A 21.7 mm (0.854 in.) B 22.6 mm (0.890 in.)
C 8.3 mm (0.327 in.) D 8.0 mm (0.315 in.)
E 3.9 to 6.9 mm (0.154 to 0.272 in.) F -0.8 to 2.2 mm (-0.0315 to 0.0866 in.)
G 2.3 to 5.3 mm (0.0906 to 0.2087 in.) H -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)




HINT:

Centering bolts are used to mount the hood hinge to the vehicle body and hood. The hood cannot be adjusted with the centering bolts on. Substitute the centering bolts for standard bolts (with washers) when making adjustments.


ADJUST HOOD SUB-ASSEMBLY


a.
B537832

Adjust the hood position.

i.

Loosen the 4 hinge bolts on the hood and adjust the hood position.


ii.

Move the hood and adjust the clearance between the hood and front fender.


iii.

Tighten the 4 hinge bolts on the hood after the adjustment.

Torque:
11.5 N*m (117 kgf*cm, 8 ft.*lbf)



b.
B537833

Adjust the 4 cushion rubbers so that the hood and fender are aligned.

HINT:

Raise or lower the front end of the hood by turning the cushion rubber.



c.
B537834C01
0,0 0,0 false
V100155

Protective Tape


Adjust the hood lock.

i.

Using a screwdriver with its tip wrapped in protective tape, remove the hood lock nut cap.


ii.
B537835C01
1.76,1.438 2.167,1.74 true 2.24,1.688 2.448,1.854 0.208,0.167 10 true *1
*1 Hood Lock Bolt


Loosen the 2 bolts and hood lock bolt.


iii.

Adjust the hood lock position so that the striker can enter it smoothly.


iv.
B537836C01
1.75,1.469 2.208,1.792 true 1.781,3.938 2.24,4.26 true 0.083,0.083 0.344,0.313 0.26,0.229 12 true *A 0.104,2.667 0.365,2.917 0.26,0.25 12 true *B 2.26,1.698 2.427,1.875 0.167,0.177 10 true *1 2.292,4.177 2.458,4.354 0.167,0.177 10 true *1
*A for LHD
*B for RHD
*1 Hood Lock Bolt


Tighten the 2 bolts and hood lock bolt after the adjustment in the order shown in the illustration.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


v.
B537837

Install a new hood lock nut cap.




INSPECT FRONT DOOR PANEL SUB-ASSEMBLY LH


a.

Check that the clearance measurements of areas A to N are within the standard ranges.

B537921N01
0.844,1.448 1.052,1.646 0.208,0.198 10 false A 1.271,1.615 1.479,1.813 0.208,0.198 10 false B 0.99,4.125 1.198,4.323 0.208,0.198 10 false C 1.49,4.271 1.698,4.469 0.208,0.198 10 false D 3.729,5.385 3.948,5.594 0.219,0.208 10 false E 3.688,4.792 3.896,4.99 0.208,0.198 10 false F 5.333,4.667 5.542,4.865 0.208,0.198 10 false G 5.833,4.958 6.042,5.156 0.208,0.198 10 false H 6.271,2.896 6.479,3.094 0.208,0.198 10 false I 5.656,3.146 5.865,3.344 0.208,0.198 10 false J 5.927,0.677 6.135,0.875 0.208,0.198 10 false K 5.49,0.854 5.698,1.052 0.208,0.198 10 false L 3.031,0.698 3.24,0.896 0.208,0.198 10 false M 2.667,0.198 2.875,0.396 0.208,0.198 10 false N

Standard Clearance:
Area Measurement Area Measurement
A 4.5 to 7.5 mm (0.177 to 0.295 in.) B -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
C 3.2 to 6.2 mm (0.126 to 0.244 in.) D -1.4 to 1.6 mm (-0.0551 to 0.0630 in.)
E 4.2 to 7.2 mm (0.165 to 0.283 in.) F -6.0 to -3.0 mm (-0.236 to -0.118 in.)
G 3.6 to 6.6 mm (0.142 to 0.260 in.) H -4.4 to -1.4 mm (-0.1732 to -0.0551 in.)
I 3.2 to 6.2 mm (0.126 to 0.244 in.) J -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
K 3.2 to 6.2 mm (0.126 to 0.244 in.) L -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
M 3.2 to 6.2 mm (0.126 to 0.244 in.) N 1.0 to 4.0 mm (0.0394 to 0.1575 in.)




HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

Use the same procedure described for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts for standard bolts when making adjustments.



ADJUST FRONT DOOR PANEL SUB-ASSEMBLY LH


a.

Remove the front pillar upper cover sub-assembly LH.


b.
B537922

Using SST, loosen the hinge bolts on the body and adjust the door position.

SST
09812-00010  


c.

Tighten the hinge bolts on the body after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


d.
B537923

Loosen the hinge bolts on the door and adjust the door position.


e.

Tighten the hinge bolts on the door after the adjustment.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


f.
B537924

Using a T40 "TORX" socket wrench, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a brass bar and a hammer.


g.

Using a T40 "TORX" socket wrench, tighten the striker mounting screws after the adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


h.

Install the front piller upper cover sub-assembly LH.



INSPECT SLIDE DOOR SUB-ASSEMBLY LH (for Wagon)


a.

Check that the clearance measurements of areas A to N are within the standard ranges.

B539220N01
6.25,3.594 6.406,3.792 0.156,0.198 10 false A 6.625,4.229 6.781,4.427 0.156,0.198 10 false B 6.25,2.271 6.406,2.469 0.156,0.198 10 false C 6.615,2.927 6.771,3.125 0.156,0.198 10 false D 6.594,1.521 6.75,1.719 0.156,0.198 10 false F 6.25,0.865 6.406,1.063 0.156,0.198 10 false E 3.625,0.156 3.781,0.354 0.156,0.198 10 false G 3.698,0.708 3.854,0.906 0.156,0.198 10 false H 0.677,2.365 0.833,2.563 0.156,0.198 10 false I 0.948,3 1.104,3.198 0.156,0.198 10 false J 3.125,5.188 3.281,5.385 0.156,0.198 10 false K 2.771,5.448 2.927,5.646 0.156,0.198 10 false L 4.865,5.188 5.021,5.385 0.156,0.198 10 false M 4.521,5.469 4.677,5.667 0.156,0.198 10 false N

Standard Clearance:
Area Measurement
(for Glass Type)
(except Glass Type)
Area Measurement
A 3.6 to 6.6 mm (0.142 to 0.260 in.)
3.6 to 6.6 mm (0.142 to 0.260 in.)
B -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
C 3.6 to 6.6 mm (0.142 to 0.260 in.)
3.6 to 6.6 mm (0.142 to 0.260 in.)
D -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
E 3.6 to 6.6 mm (0.142 to 0.260 in.)
3.6 to 6.6 mm (0.142 to 0.260 in.)
F -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
G 4.4 to 7.4 mm (0.173 to 0.291 in.)
4.5 to 7.5 mm (0.177 to 0.295 in.)
H -2.4 to 0.6 mm (-0.0945 to 0.0236 in.)
I 3.2 to 6.2 mm (0.126 to 0.244 in.)
3.2 to 6.2 mm (0.126 to 0.244 in.)
J -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
K 5.0 to 8.0 mm (0.197 to 0.315 in.)
5.0 to 8.0 mm (0.197 to 0.315 in.)
L -5.9 to -2.9 mm (-0.232 to -0.114 in.)
M 5.0 to 8.0 mm (0.197 to 0.315 in.)
5.0 to 8.0 mm (0.197 to 0.315 in.)
N -5.9 to -2.9 mm (-0.232 to -0.114 in.)


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

Use the same procedure described for the RH side.





ADJUST SLIDE DOOR SUB-ASSEMBLY LH (for Wagon)


a.
B539222

To adjust the door position vertically or horizontally at the slide door front lock striker plate assembly, loosen the bolts for the slide door down female stopper, loosen the striker screws using a T40 "TORX"socket wrench so that the striker can move, and then using a brass bar and hammer, adjust the striker position by tapping it lightly.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


b.
B539223

To adjust the door position vertically or horizontally at the slide door lock striker plate assembly, loosen the striker screws using a T40 "TORX" socket wrench, and then using a brass bar and hammer, adjust the position by tapping it lightly.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


c.
B539224

To adjust the door position in the vertical or front-to-back directions at the rear edge of the door, loosen the bolts of the center slide door hinge assembly LH before making an adjustment.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


d.
B539225C01
0.094,0.156 0.271,0.344 0.177,0.188 10 true *a 0.063,1.823 0.26,1.99 0.198,0.167 10 true *b
*a Door Side
*b Vehicle Body Side


To adjust the lower door seating position on the vehicle body surface vertically or to adjust the door position in the vertical and front-to-back directions, fully close the slide door, loosen the bolt of the lower slide door roller arm LH, and then check and adjust the door position.

Torque:
Door Side : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)
Vehicle Body Side : 19 N*m (194 kgf*cm, 14 ft.*lbf)

HINT:

To adjust the slide door lower roller base on the vehicle body side, detach the slide door full open stop lock assembly and temporarily install the bolts.



e.
B539226C01
0.052,1.823 0.323,2.073 0.271,0.25 10 true *a 0.063,0.042 0.323,0.271 0.26,0.229 10 true *b
*a Door Side
*b Vehicle Body Side


To adjust the door position in the vertical, horizontal or front-to-back direction, loosen the bolts of the upper slide door roller assembly LH before making an adjustment.

Torque:
Door Side : 11.5 N*m (117 kgf*cm, 8 ft.*lbf)
Vehicle Body Side : 30 N*m (306 kgf*cm, 22 ft.*lbf)


f.

Temporarily tighten the slide door down female stopper, fully close the slide door to settle the stopper, and then fully tighten the stopper.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


g.

After adjusting the door position, check the operation of the electric door lock system, slide door closer system, and power slide door system (w/ Power Slide Door).

HINT:

If something contacts the power slide door touch sensor during an automatic closing operation, the door will reverse.




INSPECT SLIDE DOOR SUB-ASSEMBLY LH (except Wagon)


a.

for Standard Roof:

i.

Check that the clearance measurements of areas A to N are within the standard ranges.

B539220N01
6.25,3.594 6.406,3.792 0.156,0.198 10 false A 6.625,4.229 6.781,4.427 0.156,0.198 10 false B 6.25,2.271 6.406,2.469 0.156,0.198 10 false C 6.615,2.927 6.771,3.125 0.156,0.198 10 false D 6.594,1.521 6.75,1.719 0.156,0.198 10 false F 6.25,0.865 6.406,1.063 0.156,0.198 10 false E 3.625,0.156 3.781,0.354 0.156,0.198 10 false G 3.698,0.708 3.854,0.906 0.156,0.198 10 false H 0.677,2.365 0.833,2.563 0.156,0.198 10 false I 0.948,3 1.104,3.198 0.156,0.198 10 false J 3.125,5.188 3.281,5.385 0.156,0.198 10 false K 2.771,5.448 2.927,5.646 0.156,0.198 10 false L 4.865,5.188 5.021,5.385 0.156,0.198 10 false M 4.521,5.469 4.677,5.667 0.156,0.198 10 false N

Standard Clearance:
Area Measurement
(for Glass Type)
(except Glass Type)
Area Measurement
(for Glass Type)
(except Glass Type)
A 3.6 to 6.6 mm (0.142 to 0.260 in.)
3.6 to 6.6 mm (0.142 to 0.260 in.)
B -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
-1.6 to 1.4 mm (-0.0630 to 0.0551 in.)
C 3.6 to 6.6 mm (0.142 to 0.260 in.)
3.6 to 6.6 mm (0.142 to 0.260 in.)
D -1.2 to 1.8 mm (-0.0472 to 0.0709 in.)
-1.4 to 1.6 mm (-0.0551 to 0.0630 in.)
E 3.6 to 6.6 mm (0.142 to 0.260 in.)
3.6 to 6.6 mm (0.142 to 0.260 in.)
F -1.4 to 1.6 mm (-0.0551 to 0.0630 in.)
-1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
G 4.4 to 7.4 mm (0.173 to 0.291 in.)
4.5 to 7.5 mm (0.177 to 0.295 in.)
H -2.4 to 0.6 mm (-0.0945 to 0.0236 in.)
-2.2 to 0.8 mm (-0.0866 to 0.0315 in.)
I 3.2 to 6.2 mm (0.126 to 0.244 in.)
3.2 to 6.2 mm (0.126 to 0.244 in.)
J -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
-1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
K 5.0 to 8.0 mm (0.197 to 0.315 in.)
5.0 to 8.0 mm (0.197 to 0.315 in.)
L -6.0 to -3.0 mm (-0.236 to -0.118 in.)
-6.2 to -3.2 mm (-0.244 to -0.126 in.)
M 5.0 to 8.0 mm (0.197 to 0.315 in.)
5.0 to 8.0 mm (0.197 to 0.315 in.)
N -5.9 to -2.9 mm (-0.232 to -0.114 in.)
-6.1 to -3.1 mm (-0.240 to -0.122 in.)




b.

for High Roof:

i.

Check that the clearance measurements of areas A to N are within the standard ranges.

B539221N01
6.25,3.583 6.406,3.781 0.156,0.198 10 false A 6.625,4.24 6.781,4.438 0.156,0.198 10 false B 6.25,2.25 6.406,2.448 0.156,0.198 10 false C 6.615,2.896 6.771,3.094 0.156,0.198 10 false D 6.24,0.854 6.396,1.052 0.156,0.198 10 false E 6.615,1.219 6.771,1.417 0.156,0.198 10 false F 3.646,0.292 3.802,0.49 0.156,0.198 10 false G 3.698,0.896 3.854,1.094 0.156,0.198 10 false H 0.688,2.344 0.844,2.542 0.156,0.198 10 false I 1.021,2.698 1.177,2.896 0.156,0.198 10 false J 3.146,5.188 3.302,5.385 0.156,0.198 10 false K 2.781,5.448 2.938,5.646 0.156,0.198 10 false L 4.875,5.208 5.031,5.406 0.156,0.198 10 false M 4.531,5.458 4.688,5.656 0.156,0.198 10 false N

Standard Clearance:
Area Measurement
(for Glass Type)
(except Glass Type)
Area Measurement
(for Glass Type)
(except Glass Type)
A 3.6 to 6.6 mm (0.142 to 0.260 in.)
3.6 to 6.6 mm (0.142 to 0.260 in.)
B -1.4 to 1.6 mm (-0.0551 to 0.0630 in.)
-1.4 to 1.6 mm (-0.0551 to 0.0630 in.)
C 3.6 to 6.6 mm (0.142 to 0.260 in.)
3.6 to 6.6 mm (0.142 to 0.260 in.)
D -1.4 to 1.6 mm (-0.0551 to 0.0630 in.)
-1.4 to 1.6 mm (-0.0551 to 0.0630 in.)
E 3.8 to 6.8 mm (0.150 to 0.268 in.)
3.8 to 6.8 mm (0.150 to 0.268 in.)
F -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
-1.6 to 1.4 mm (-0.0630 to 0.0551 in.)
G 4.6 to 7.6 mm (0.181 to 0.299 in.)
4.8 to 7.8 mm (0.189 to 0.307 in.)
H -1.1 to 1.9 mm (-0.0433 to 0.0748 in.)
-0.7 to 2.3 mm (-0.0276 to 0.0906 in.)
I 3.2 to 6.2 mm (0.126 to 0.244 in.)
3.2 to 6.2 mm (0.126 to 0.244 in.)
J -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
-1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
K 4.9 to 7.9 mm (0.193 to 0.311 in.)
4.9 to 7.9 mm (0.193 to 0.311 in.)
L -6.3 to -3.3 mm (-0.248 to -0.130 in.)
-6.3 to -3.3 mm (-0.248 to -0.130 in.)
M 5.0 to 8.0 mm (0.197 to 0.315 in.)
5.0 to 8.0 mm (0.197 to 0.315 in.)
N -5.9 to -2.9 mm (-0.232 to -0.114 in.)
-5.9 to -2.9 mm (-0.232 to -0.114 in.)





HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

Use the same procedure described for the RH side.



ADJUST SLIDE DOOR SUB-ASSEMBLY LH (except Wagon)


a.
B539222

To adjust the door position vertically or horizontally at the slide door front lock striker plate assembly, loosen the bolts for the slide door down female stopper, loosen the striker screws using a T40 "TORX"socket wrench so that the striker can move, and then using a brass bar and hammer, adjust the striker position by tapping it lightly.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


b.
B539223

To adjust the door position vertically or horizontally at the slide door lock striker plate assembly, loosen the striker screws using a T40 "TORX" socket wrench, and then using a brass bar and hammer, adjust the position by tapping it lightly.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


c.
B539224

To adjust the door position in the vertical or front-to-back directions at the rear edge of the door, loosen the bolts of the center slide door hinge assembly LH before making an adjustment.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


d.
B539225C01
0.094,0.156 0.271,0.344 0.177,0.188 10 true *a 0.063,1.823 0.26,1.99 0.198,0.167 10 true *b
*a Door Side
*b Vehicle Body Side


To adjust the lower door seating position on the vehicle body surface vertically or to adjust the door position in the vertical and front-to-back directions, fully close the slide door, loosen the bolt of the lower slide door roller arm LH, and then check and adjust the door position.

Torque:
Door Side : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)
Vehicle Body Side : 19 N*m (194 kgf*cm, 14 ft.*lbf)

HINT:

To adjust the slide door lower roller base on the vehicle body side, detach the slide door full open stop lock assembly and temporarily install the bolts.



e.
B539226C01
0.052,1.823 0.323,2.073 0.271,0.25 10 true *a 0.063,0.042 0.323,0.271 0.26,0.229 10 true *b
*a Door Side
*b Vehicle Body Side


To adjust the door position in the vertical, horizontal or front-to-back direction, loosen the bolts of the upper slide door roller assembly LH before making an adjustment.

Torque:
Door Side : 11.5 N*m (117 kgf*cm, 8 ft.*lbf)
Vehicle Body Side : 30 N*m (306 kgf*cm, 22 ft.*lbf)


f.

Temporarily tighten the slide door down female stopper, fully close the slide door to settle the stopper, and then fully tighten the stopper.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


g.

After adjusting the door position, check the operation of the electric door lock system, slide door closer system, and power slide door system (w/ Power Slide Door).

HINT:

If something contacts the power slide door touch sensor during an automatic closing operation, the door will reverse.




INSPECT BACK DOOR PANEL SUB-ASSEMBLY (for Wagon)


a.

Check that the clearance measurements of areas A to L are within the standard ranges.

B551640N01
1.115,1.281 1.271,1.479 0.156,0.198 10 false A 1.49,1.583 1.646,1.781 0.156,0.198 10 false B 2.323,1.281 2.479,1.479 0.156,0.198 10 false C 2.656,1.573 2.813,1.771 0.156,0.198 10 false D 6.781,0.667 6.938,0.865 0.156,0.198 10 false E 6.427,0.375 6.583,0.573 0.156,0.198 10 false F 6.49,1.583 6.646,1.781 0.156,0.198 10 false G 6.135,1.813 6.292,2.01 0.156,0.198 10 false H 6.5,3.219 6.656,3.417 0.156,0.198 10 false I 5.948,3.25 6.104,3.448 0.156,0.198 10 false J 4.396,3.875 4.552,4.073 0.156,0.198 10 false K 4.521,3.521 4.677,3.719 0.156,0.198 10 false L

Standard Clearance:
Area Measurement Area Measurement
A 7.7 to 10.7 mm (0.303 to 0.421 in.) B 2.1 to 5.1 mm (0.0827 to 0.2008 in.)
C 7.7 to 10.7 mm (0.303 to 0.421 in.) D 1.6 to 4.6 mm (0.0630 to 0.1811 in.)
E 4.0 to 7.0 mm (0.157 to 0.276 in.) F -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
G 3.15 to 7.15 mm (0.124 to 0.281 in.) H 2.5 mm (0.0984 in.)
I 3.15 to 7.15 mm (0.124 to 0.281 in.) J 36.6 mm (1.44 in.)
K 5.85 to 9.85 mm (0.230 to 0.388 in.) L 49.9 mm (1.96 in.)


HINT:

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts for standard bolts when making adjustments.




ADJUST BACK DOOR PANEL SUB-ASSEMBLY (for Wagon)


a.
B539229

Before adjusting the upper end of the back door up and down or left and right, loosen the bolts.


b.

Tighten the hinge bolts on the body after the adjustment.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


c.
B539230

Adjust the striker position by slightly loosening the striker mounting bolts and hitting the striker with a brass bar and a hammer.


d.

Tighten the striker mounting bolts after the adjustment.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


e.
B539232

w/ Bracket:

i.

After completing fitting adjustment, confirm the position of the back door side female stopper sub-assembly and back door side male stopper sub-assembly.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)



f.
B539231

w/o Bracket:

i.

After completing fitting adjustment, confirm the position of the back door No. 1 stopper and back door stopper cushion.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)




INSPECT BACK DOOR PANEL SUB-ASSEMBLY (except Wagon)


a.

for Standard Roof:

i.

Check that the clearance measurements of areas A to L are within the standard ranges.

B539227N01
1.115,1.281 1.271,1.479 0.156,0.198 10 false A 1.49,1.583 1.646,1.781 0.156,0.198 10 false B 2.323,1.281 2.479,1.479 0.156,0.198 10 false C 2.656,1.573 2.813,1.771 0.156,0.198 10 false D 6.865,0.74 7.021,0.938 0.156,0.198 10 false E 6.427,0.375 6.583,0.573 0.156,0.198 10 false F 6.552,1.729 6.708,1.927 0.156,0.198 10 false G 6.146,1.948 6.302,2.146 0.156,0.198 10 false H 6.531,3.021 6.688,3.219 0.156,0.198 10 false I 6.073,3.365 6.229,3.563 0.156,0.198 10 false J 4.688,3.938 4.844,4.135 0.156,0.198 10 false K 4.583,4.323 4.74,4.521 0.156,0.198 10 false L

Standard Clearance:
Area Measurement Area Measurement
A 7.8 to 10.8 mm (0.307 to 0.425 in.) B 2.8 to 5.8 mm (0.110 to 0.228 in.)
C 7.9 to 10.9 mm (0.311 to 0.429 in.) D 2.1 to 5.1 mm (0.0827 to 0.2008 in.)
E 4.3 to 7.3 mm (0.169 to 0.287 in.) F -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
G 3.5 to 7.5 mm (0.138 to 0.295 in.) H
(Reference)
2.3 mm (0.0906 in.)
I 3.5 to 7.5 mm (0.138 to 0.295 in.) J
(Reference)
11.6 mm (0.457 in.)
K 5.8 to 9.8 mm (0.228 to 0.386 in.) L
(Reference)
26.7 mm (1.051 in.)




b.

for High Roof:

i.

Check that the clearance measurements of areas A to L are within the standard ranges.

B539228N01
1.073,1.219 1.229,1.417 0.156,0.198 10 false A 1.615,1.552 1.771,1.75 0.156,0.198 10 false B 2.333,1.26 2.49,1.458 0.156,0.198 10 false C 2.885,1.542 3.042,1.74 0.156,0.198 10 false D 6.875,0.75 7.031,0.948 0.156,0.198 10 false E 6.427,0.375 6.583,0.573 0.156,0.198 10 false F 6.552,1.729 6.708,1.927 0.156,0.198 10 false G 6.167,1.927 6.323,2.125 0.156,0.198 10 false H 6.531,3.052 6.688,3.25 0.156,0.198 10 false I 6.063,3.354 6.219,3.552 0.156,0.198 10 false J 4.74,3.844 4.896,4.042 0.156,0.198 10 false K 4.552,4.344 4.708,4.542 0.156,0.198 10 false L

Standard Clearance:
Area Measurement Area Measurement
A 13.1 to 16.1 mm (0.516 to 0.634 in.) B 3.4 to 6.4 mm (0.134 to 0.252 in.)
C 13.2 to 16.2 mm (0.520 to 0.638 in.) D 2.9 to 5.9 mm (0.114 to 0.232 in.)
E 4.3 to 7.3 mm (0.169 to 0.287 in.) F -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
G 3.5 to 7.5 mm (0.138 to 0.295 in.) H
(Reference)
2.3 mm (0.0906 in.)
I 3.5 to 7.5 mm (0.138 to 0.295 in.) J
(Reference)
11.6 mm (0.457 in.)
K
(Reference)
8.0 mm (0.315 in.) L
(Reference)
26.7 mm (1.051 in.)





HINT:

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts for standard bolts when making adjustments.


ADJUST BACK DOOR PANEL SUB-ASSEMBLY (except Wagon)


a.
B539229

Before adjusting the upper end of the back door up and down or left and right, loosen the bolts.


b.

Tighten the hinge bolts on the body after the adjustment.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


c.
B539230

Adjust the striker position by slightly loosening the striker mounting bolts and hitting the striker with a brass bar and a hammer.


d.

Tighten the striker mounting bolts after the adjustment.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


e.
B539232

w/ Bracket:

i.

After completing fitting adjustment, confirm the position of the back door side female stopper sub-assembly and back door side male stopper sub-assembly.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)



f.
B539231

w/o Bracket:

i.

After completing fitting adjustment, confirm the position of the back door No. 1 stopper and back door stopper cushion.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)