Heat the double-sided tape remaining on the body with an infrared lamp or equivalent.
Heat the tape to 40 to 60°C for approximately 1 to 2 minutes.
Wipe off the remaining double-sided tape using a clean cloth or equivalent.
If a name plate is installed without thoroughly removing the remaining double-sided tape from the body, the name plate will not adhere properly. Make sure to thoroughly wipe off the double-sided tape.
After cleaning the installation area of the body with degreasing agent, attach the name plate to the position shown in the illustration.
The working environment should be 20°C when installing the name plate. If the working environment is below 20°C, heat the installation area of the body to 20 to 30°C and then install the name plate.
| *A | for Wagon | *B | except Wagon |
| *1 | RADIATOR GRILLE (OR FRONT PANEL) EMBLEM | - | - |
| ● | Non-reusable part | - | - |
| *A | for Plate Type | *B | for Wagon |
| *1 | BACK DOOR NAME PLATE | - | - |
| ● | Non-reusable part | - | - |
| *A | for Plate Type | *B | except Wagon |
| *C | for Type A | *D | for Type B |
| *E | for Type C | - | - |
| *1 | BACK DOOR NAME PLATE | - | - |
| ● | Non-reusable part | - | - |
| *A | for Sticker Type | *B | for Type A |
| *C | for Type B | *D | for Type C |
| *1 | BACK DOOR NAME PLATE | - | - |
| ● | Non-reusable part | - | - |
| *A | for Wagon | *B | for Type A |
| *C | for Type B | *D | for Type C |
| *1 | BACK DOOR NO. 1 EMBLEM | *2 | BACK DOOR NO. 3 NAME PLATE |
| ● | Non-reusable part | - | - |
| *A | except Wagon | - | - |
| *1 | BACK DOOR NO. 1 EMBLEM | *2 | BACK DOOR NO. 3 NAME PLATE |
| ● | Non-reusable part | - | - |
RADIATOR GRILLE (OR FRONT PANEL) EMBLEM
| *a | Boss Position |
for Wagon:
| *a | Boss Position |
except Wagon:
BACK DOOR NO. 1 EMBLEM
| *a | Boss Position |
for Wagon:
| *a | Boss Position |
except Wagon:
BACK DOOR NAME PLATE (for Plate Type)
for Wagon:
Model Name HIACE:
| *a | Reference Values | *b | Back Door Crease Line |
| *c | Application External Form Line | - | - |
| Area | Dimensions | Area | Dimensions |
|---|---|---|---|
| A | 253.8 mm (9.99 in.) | B | 253.6 mm (9.98 in.) |
Model Name MAJESTY:
| *a | Reference Values | *b | Back Door Crease Line |
| *c | Application External Form Line | - | - |
| Area | Dimensions | Area | Dimensions |
|---|---|---|---|
| A | 251.6 mm (9.91 in.) | B | 253.4 mm (9.98 in.) |
Model Name GRANVIA:
| *a | Reference Values | *b | Back Door Crease Line |
| *c | Application External Form Line | - | - |
| Area | Dimensions | Area | Dimensions |
|---|---|---|---|
| A | 268.5 mm (10.6 in.) | B | 253.4 mm (9.98 in.) |
except Wagon:
for Type A:
| *a | Reference Values | *b | Back Door Crease Line |
| *c | Application External Form Line | - | - |
| Area | Dimensions | Area | Dimensions |
|---|---|---|---|
| A | 271.9 mm (10.7 in.) | B | 277.6 mm (10.9 in.) |
for Type B:
| *a | Reference Values | *b | Back Door Crease Line |
| *c | Application External Form Line | - | - |
| Area | Dimensions | Area | Dimensions |
|---|---|---|---|
| A | 271.9 mm (10.7 in.) | B | 277.6 mm (10.9 in.) |
for Type C:
| *a | Reference Values | *b | Back Door Crease Line |
| *c | Application External Form Line | - | - |
| Area | Dimensions | Area | Dimensions |
|---|---|---|---|
| A | 325.6 mm (1.068 ft.) | B | 326.8 mm (1.072 ft.) |
BACK DOOR NAME PLATE (for Sticker Type)
for Type A:
| *a | Reference Values | *b | Back Door Crease Line |
| *c | Application External Form Line | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 271.9 mm (10.7 in.) | B | 277.6 mm (10.9 in.) |
for Type B:
| *a | Reference Values | *b | Back Door Crease Line |
| *c | Application External Form Line | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 271.9 mm (10.7 in.) | B | 277.6 mm (10.9 in.) |
for Type C:
| *a | Reference Values | *b | Back Door Crease Line |
| *c | Application External Form Line | - | - |
| Area | Dimensions | Area | Dimensions |
|---|---|---|---|
| A | 325.6 mm (1.068 ft.) | B | 326.8 mm (1.072 ft.) |
BACK DOOR NO. 3 NAME PLATE
for Wagon:
for Type A:
| *a | Reference Values | *b | Back Door Crease Line |
| *c | Application External Form Line | - | - |
| Area | Dimensions | Area | Dimensions |
|---|---|---|---|
| A | 253.7 mm (9.99 in.) | B | 256.7 mm (10.1 in.) |
for Type B:
| *a | Reference Values | *b | Back Door Crease Line |
| *c | Application External Form Line | - | - |
| Area | Dimensions | Area | Dimensions |
|---|---|---|---|
| A | 252.8 mm (9.95 in.) | B | 252.7 mm (9.95 in.) |
for Type C:
| *a | Reference Values | *b | Back Door Crease Line |
| *c | Application External Form Line | - | - |
| Area | Dimensions | Area | Dimensions |
|---|---|---|---|
| A | 240.3 mm (9.46 in.) | B | 258.2 mm (10.2 in.) |
except Wagon:
| *a | Reference Values | *b | Back Door Crease Line |
| *c | Application External Form Line | - | - |
| Area | Dimensions | Area | Dimensions |
|---|---|---|---|
| A | 277.3 mm (10.9 in.) | B | 271.7 mm (10.7 in.) |