FUNCTION OF MAIN COMPONENTS
The main components in the cruise control system have the following functions:
| Component | Function | |
|---|---|---|
|
*1: Models with diesel engine *2: Models with gasoline engine *3: Models with automatic transmission *4: Models with manual transmission *5: Models with segment LCD monitor type multi-information display *6: Models with TFT LCD monitor type multi-information display *7: Models with downhill brake control *8: Models with VSC |
||
| ECM | ·
Controls the cruise control system in accordance with signals from the switches and sensors. ·
Controls the fuel injection volume from the injectors according to various situations.*1 ·
Actuates the throttle control motor according to various situations.*2 ·
If the ECM detects a malfunction in the cruise control system, it will store a Diagnostic Trouble Code (DTC). |
|
| Steering Pad Switch Assembly | Cruise Control Main Switch | Turns on/off the power to the cruise control system. |
| -SET Switch | The deceleration function and set control function can be performed by operating this switch. | |
| +RES Switch | The acceleration function and resume control function can be performed by operating this switch. | |
| CANCEL Switch | A cancel signal can be output to the ECM through the operation of this switch. | |
| Injector*1 | Adjusts the fuel injection volume based on the signals. | |
| Throttle Body with Motor Assembly*2 | Throttle Control Motor | Adjusts the throttle valve to the limiter position in accordance with signals from the ECM. |
| Throttle Position Sensor | Sends the throttle valve position information to the ECM. | |
| Stop Light Switch Assembly | Detects the depressing of the brake pedal and sends a signal to the ECM. | |
| Accelerator Pedal Sensor Assembly | Detects the accelerator pedal depression degree and sends it to the ECM. | |
| Park/Neutral Position Switch Assembly*3 | Detects the shift position and sends signals to the ECM. | |
| Transmission Control Switch*3 | ·
Detects the shift lever position and transmits signals to the ECM. ·
Informs the ECM of driver upshift or downshift operations while the shift lever is in S. |
|
| Clutch Switch Assembly*4 | Detects the depressing of the clutch pedal and sends a signal to the ECM. | |
| Combination Meter Assembly | Cruise Control Indicator | ·
Illuminates when the cruise control main switch has been pressed to turn the cruise control system on. ·
If the ECM detects a malfunction, this light illuminates in yellow*5 or turns off*6. |
| Cruise Control SET Indicator | Illuminates when the -SET switch on the steering pad switch assembly has been pressed to set the cruise control system. | |
| Multi-information Display*6 | ·
During cruise control operation, the multi-information display receives signals from the ECM in order to display the system conditions. ·
Displays a warning message to alert the driver in accordance with a signal provided by the ECM. |
|
| Meter Buzzer*6 | Sounds to warn the driver of a malfunction in the cruise control system. | |
| Brake Actuator Assembly | - | Performs brake control according to brake request signals from the skid control ECU.*7 |
| Skid Control ECU | ·
Sends a vehicle speed signal to the ECM. ·
Sends the VSC, TRC and AUTO LSD control status to the ECM.*8 ·
Operates the brake in accordance with the brake request signal received from the ECM.*7 |
|
| Central Gateway ECU (Network Gateway ECU) | Sends the signal between the CAN communication buses. | |
| DLC3 | The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions. | |
FUNCTION
The cruise control system has the following functions:
| Function | Outline |
|---|---|
|
*1: Models with automatic transmission *2: Models with downhill brake control *3: Models with manual transmission *4: Models with TFT LCD monitor type multi-information display *5: Models with segment LCD monitor type multi-information display *6: Models with VSC |
|
| Constant Speed Control | The ECM compares the actual vehicle speed with the set speed. If the vehicle speed is higher than the set speed, the ECM calculates the optimal motive forces, and decelerates by adjusting the respective motive forces. If the vehicle speed is lower than the set speed, the ECM calculates the optimal motive forces, and accelerates by adjusting the respective motive forces. |
| Set Control | When this system fulfills the following conditions, and the -SET switch on the steering pad switch assembly is pressed and released, the ECM stores the vehicle speed and maintains the vehicle constantly at that speed.
·
The cruise control system has been turned on using the cruise control main switch on the steering pad switch assembly. ·
The vehicle is driving at a speed of approximately 30 km/h (20 mph) or more. |
| Low Speed Limit Control | The low speed limit is the lowest speed that cruise control can be set at and it is designed to be approximately 30 km/h (20 mph). The cruise control system cannot be set below that speed. If the vehicle speed drops below that speed while the cruise control is operating, speed control by the cruise control system will be canceled automatically. However, the set speed is kept in memory. |
| Coast Control | While the -SET switch on the steering pad switch assembly is pushed continuously, the vehicle speed and the set vehicle speed change as follows:
·
The vehicle decelerates constantly. ·
The set vehicle speed changes to the speed at which the -SET switch is released. |
| Tap Down Control | When the -SET switch on the steering pad switch assembly is pushed momentarily (approximately 0.6 seconds or less), the vehicle speed and the set vehicle speed change as follows:
·
The vehicle will decelerate in increments of approximately 1 km/h or 1 mph each time the switch is pushed. ·
However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will change to the speed at which the vehicle is being driven when the switch is pushed. |
| Accelerator Control | While the +RES switch on the steering pad switch assembly is pushed continuously, the vehicle speed and the set vehicle speed change as follows:
·
The vehicle accelerates constantly. ·
The set vehicle speed changes to the speed at which the +RES switch is released. |
| Tap Up Control | When the +RES switch on the steering pad switch assembly is pushed momentarily (approximately 0.6 seconds or less), the vehicle speed and the set vehicle speed change as follows:
·
The vehicle will accelerate in increments of approximately 1 km/h or 1 mph each time the switch is pushed. ·
However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will not change. |
| Resume Control | When the vehicle speed is above the low speed limit, the cruise control system resumes operation (when the +RES switch on the steering pad switch assembly is pushed) to reach the vehicle speed that was set at the time the driver canceled cruise control. Even if the vehicle speed dropped below the low speed limit, the set speed can be resumed after the vehicle speed increases above the low speed limit. Also, if the vehicle speed memory is deleted, the return control cannot be performed. |
| Shift Down Control*1 | When the vehicle is traveling uphill using cruise control, automatic transmission control may cause the transmission to shift down. During shift down control, when the end of uphill travel is determined, the transmission will shift up after a certain period of time. When the transmission shifts down during the accelerator control or the resume control, the transmission will shift up after the accelerator control or the resume control ends. |
| Downhill Brake Control*2 | Operates the brakes to suppress vehicle speed increases on downhill slopes during cruise control operation. |
| Manual Cancel Control | If any of the following signals is sent to the ECM while the cruise control system is running, the cruise control system is canceled accordingly.
·
Stop light switch on signal (depress the brake pedal). ·
Clutch switch assembly off signal (depress the clutch pedal).*3 ·
Shift position is changed from D or S to any other position.*1 ·
Signal to select the S1, S2 and S3 ranges*1 ·
Cruise control main switch off signal. ·
CANCEL switch on signal (CANCEL switch on the steering pad switch assembly is pushed). |
| Automatic Cancel Control | If the following condition occurs during cruise control operation, the speed that is set in memory is cleared and cruise control operation is canceled.
·
Stop light switch assembly open or short circuit Furthermore, the following warnings are performed and the cruise control system is disabled until the cruise control system is turned on again using the cruise control main switch on the steering pad switch assembly. ·
The cruise control indicator turns off, and displays a warning message on the multi-information display until the cruise control system is turned off using the cruise control main switch on the steering pad switch assembly.*4 ·
The cruise control indicator illuminates in yellow until the cruise control system is turned off using the cruise control main switch on the steering pad switch assembly.*5 |
| If the following condition occurs during cruise control operation, the speed that is set in memory is cleared and cruise control operation is canceled.
·
Malfunction in the engine system Furthermore, the cruise control system is disabled until the cruise control system is turned on again using the cruise control main switch on the steering pad switch assembly. |
|
| If any of the following conditions occur during cruise control operation, the speed that is set in memory is cleared and cruise control operation is canceled.
·
Stop light switch assembly input signal is abnormal. ·
Cancel circuit malfunction. ·
Brake control system malfunction. ·
Communication malfunction between the skid control ECU and ECM. Furthermore, the following warnings are performed and the cruise control system is disabled until the ignition switch is turned off. ·
The cruise control indicator turns off, and displays a warning message on the multi-information display until the cruise control system is turned off using the cruise control main switch on the steering pad switch assembly.*4 ·
The cruise control indicator illuminates in yellow until the cruise control system is turned off using the cruise control main switch on the steering pad switch assembly.*5 |
|
| If the following condition occurs during cruise control operation, the speed that is set in memory is cleared and cruise control operation is canceled.
·
Vehicle speed decreases by 16 km/h (10 mph) or more below the speed at which the cruise control is set. |
|
| If the following condition occurs during cruise control operation, the speed that is set in memory is maintained and cruise control operation is canceled.
·
Vehicle speed decreases below the low speed limit. |
|
| Other Control | If any of the following conditions occur during cruise control operation, the speed that is set in memory is maintained and cruise control operation is canceled.
- VSC is activated.*6 - TRC is activated for a period of time.*6 - AUTO LSD is turned to on.*6 - The VSC system is turned off.*6 |
| When the ignition switch is turned off, the speed that is set in memory is cleared. | |
Cruise Control Operation Switch
The operation switches of the cruise control system (cruise control main switch, -SET switch, +RES switch and CANCEL switch) are positioned in the steering pad switch assembly.
| Component | Function |
|---|---|
| Cruise Control Main Switch | Turns the cruise control system on and off. |
| +RES Switch | Performs accelerator control, tap-up control and resume control. |
| -SET Switch | Performs set control, coast control and tap-down control. |
| CANCEL Switch | Cancels control. |
| *1 | +RES Switch | *2 | -SET Switch |
| *3 | CANCEL Switch | *4 | Cruise Control Main Switch |
DIAGNOSIS
In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The DTCs of malfunctioning parts can be read by connecting the Global TechStream (GTS). Refer to the Repair Manual for details.