FUNCTION OF MAIN COMPONENTS
The main components in the speed limiter system have the following functions:
| Component | Function | |
|---|---|---|
|
*1: Models with diesel engine *2: Models with gasoline engine *3: Models with automatic transmission *4: Models with manual transmission |
||
| ECM | ·
Controls the speed limiter system in accordance with signals from the switches and sensors. ·
Controls the fuel injection volume from the injectors according to various situations.*1 ·
Actuates the throttle control motor according to various situations.*2 ·
If the ECM detects a malfunction in the speed limiter system, it will store a Diagnostic Trouble Code (DTC). |
|
| Steering Pad Switch Assembly | Speed Limiter Switch | Turns the speed limiter system on and off. |
| Cruise Control Main Switch | Turns the cruise control system on and off. | |
| -SET Switch | The deceleration function and set control function can be performed by operating this switch. | |
| +RES Switch | Increases the limit speed or resumes a preset limit speed. | |
| CANCEL Switch | A cancel signal is output to the ECM when this switch is operated. | |
| Combination Meter Assembly | Speed Limiter Indicator | ·
Illuminates when the speed limiter switch has been pressed to turn the speed limiter system on. ·
If the ECM detects a malfunction in the speed limiter system, this light turns off. |
| Multi-information Display | ·
During speed limiter control operation, the multi-information display receives signals from the ECM in order to display the system conditions. ·
Displays a warning message to alert the driver in accordance with a signal provided by the ECM. |
|
| Meter Buzzer | If the ECM detects a malfunction in the speed limiter system or warning signals while the vehicle is operating under speed limiter control, this buzzer sounds to inform the driver. | |
| Injector*1 | Adjusts the fuel injection volume based on the signals. | |
| Throttle Body Assembly*2 | Throttle Control Motor | Adjusts the throttle valve opening angle in accordance with signals from the ECM. |
| Throttle Position Sensor | Detects the throttle valve opening angle and outputs it to the ECM. | |
| Skid Control ECU | ·
Sends a vehicle speed signal to the ECM. ·
Sends the VSC and AUTO LSD control status to the ECM. |
|
| Accelerator Pedal Sensor Assembly | Detects depressing of the accelerator pedal, whether the depressing of the accelerator pedal has exceeded the kick down mode threshold and sends signals to the ECM. | |
| Park/Neutral Position Switch Assembly*3 | Detects the shift position and sends signals to the ECM. | |
| Clutch Switch Assembly*4 | Detects the depressing of the clutch pedal and sends a signal to the ECM. | |
| Central Gateway ECU (Network Gateway ECU) | Sends the signal between the CAN communication buses. | |
| DLC3 | The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions. | |
FUNCTION
The speed limiter system has the following functions:
| Function | Outline |
|---|---|
|
*1: Models with automatic transmission *2: Models with manual transmission |
|
| Set Control | When the driver turns on the speed limiter switch, the speed limiter indicator will illuminate in the combination meter assembly. In this state, when the -SET switch is pressed, the system will memorize the speed that the vehicle was traveling at prior to the operation of the -SET switch as a limit speed, and display the limit speed on the multi-information display (If the -SET switch is pressed while the vehicle is being driven at 30 km/h [20 mph] or less, or while the vehicle is stopped, the system will memorize the limit speed as being approximately 30 km/h [20 mph]). |
| Constant Speed Control | When the speed limiter control is on, the ECM will compare the actual vehicle speed with the limit speed. If the actual vehicle speed is greater than the limit speed, the ECM decelerates by adjusting the motive forces. As a result, the system reduces the actual vehicle speed to the limit speed. |
| Coast Control | If the driver continues to press the -SET switch, the system will reduce the limit speed in 5 km/h or 5 mph increments. The instant the driver releases the -SET switch, that speed will be rendered as the set speed. |
| Tap-down Control | If the driver presses the -SET switch momentarily (approximately 0.6 seconds), the system will reduce the limit speed by 1 km/h or 1 mph with each press of the switch. |
| Accelerator Control | If the driver continues to press the +RES switch, the system will increase the limit speed in 5 km/h or 5 mph increments. The instant the driver releases the +RES switch, that speed will be rendered as the limit speed. |
| Tap-up Control | If the driver presses the +RES switch momentarily (approximately 0.6 seconds), the system will increase the limit speed by 1 km/h or 1 mph with each press of the switch. |
| Override Control | While driving the vehicle with speed limiter system on, if the driver fully depresses the accelerator pedal, the ECM will detect that the accelerator pedal sensor assembly is in kick down mode. Then, the ECM will recognize this to be the driver's acceleration requirement, and allow the vehicle to accelerate higher than the limit speed. After the acceleration, when the vehicle speed falls below the limit speed, this function will resume limit speed control. |
| Cancel Control | If any of the following conditions occur during speed limiter operation, the speed that is set in memory is maintained and speed limiter operation is canceled.
·
CANCEL switch on. (CANCEL switch is pushed) ·
VSC system is turned off. ·
AUTO LSD is turned to on. |
| If any of the following conditions occur during speed limiter operation, the speed that is set in memory is cleared and speed limiter operation is canceled.
·
Speed limiter switch off. (speed limiter switch is pushed) ·
Cruise control main switch on. (transfers to the cruise control system, turns off the speed limiter indicator, and deletes the limit speed) ·
Malfunction in the vehicle speed. ·
Communication malfunction between the skid control ECU and ECM. ·
Malfunction in the engine system |
|
| Resume Control | After speed limiter control is canceled by turning the CANCEL switch on, turning the VSC off or turning the AUTO LSD on, if the driver pushes the +RES switch, the system will limit the vehicle speed at the limit speed that was set at the time of cancelation. |
| Interruption Control*1 | If the shift position is changed to R during speed limiter control, the limit speed cannot be changed by operating switches. |
| Others | ·
When the ignition switch is turned off, the speed that is set in memory is cleared. ·
While the clutch pedal is depressed, the system temporarily deactivates the speed limiter control.*2 |
Speed Limiter Operation Switch
The operation switches of the speed limiter system (speed limiter switch, cruise control main switch, -SET switch, +RES switch and CANCEL switch) are positioned in the steering pad switch assembly.
| Component | Function |
|---|---|
| Speed Limiter Switch | Turns the speed limiter system on and off. |
| Cruise Control Main Switch | Turns the cruise control system on and off. |
| +RES Switch | Performs accelerator control, tap-up control and resume control. |
| -SET Switch | Performs set control, coast control and tap-down control. |
| CANCEL Switch | Cancels control. |
| *1 | +RES Switch | *2 | -SET Switch |
| *3 | Speed Limiter Switch | *4 | CANCEL Switch |
| *5 | Cruise Control Main Switch | - | - |
DIAGNOSIS
In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The DTCs of malfunctioning parts can be read by connecting the Global TechStream (GTS). Refer to the Repair Manual for details.