FUNCTION OF MAIN COMPONENTS
The main components in the lane departure alert system have the following functions:
| Components | Function | |
|---|---|---|
| Forward Recognition Camera | ·
Controls the lane departure alert system. ·
Calculates the amount of brake assist in accordance with signals from switch and ECUs. ·
Captures a view of the road ahead of the vehicle and detects lane markers or lane boundaries on the driving lane, and calculates the radius to the center of the lane, lane width, distance from markers and heading angle deviation. ·
Sends the indicator illumination request signal, multi-information display indication request signal, and meter buzzer sound request signal to the combination meter assembly. ·
Receives vehicle information and turn signal light operation signals, and sends a brake control request signal to the skid control ECU. ·
Controls the supply of electric current to the camera heater when the ambient temperature is low. |
|
| Camera Heater (Forward Recognition Hood with Heater Sub-assembly) | Control is performed by the forward recognition camera to supply electric current and heat the heater, preventing the windshield glass in front of the forward recognition camera from fogging up. | |
| Steering Vibration ECU | Operates the steering wheel motor according to an eccentric motor operation request signal from the forward recognition camera. | |
| Steering Wheel Motor | Operates according to a signal from the steering vibration ECU to vibrate the steering wheel assembly. | |
| Millimeter Wave Radar Sensor Assembly | Radiates millimeter waves forward, uses the reflected waves to detect the presence of a vehicle traveling ahead, the vehicle-to-vehicle distance, and the relative speed, and then sends this information to the forward recognition camera. | |
| Combination Meter Assembly | - | Sends a turn signal command to the forward recognition camera. |
| LDA Indicator | Illuminates in accordance with signals from the forward recognition camera. | |
| Multi-information Display | Displays a warning message and white lines to inform or warn the driver of the system condition in accordance with signals from the forward recognition camera. | |
| Meter Buzzer | Sounds to warn the driver in accordance with signals from the forward recognition camera. | |
| ECM | Sends the shift position signal to the forward recognition camera. | |
| Brake Actuator Assembly | Brake Actuator | Performs brake control of wheels on one side of the vehicle according to brake control request signals from the skid control ECU. |
| Skid Control ECU | ·
Sends brake control request signals from the forward recognition camera to the brake actuator. ·
Cancels brake control when an abnormal yaw moment request is detected from the forward recognition camera. ·
Sends a vehicle speed signal to the forward recognition camera. |
|
| Steering Pad Switch Assembly | LDA Main Switch | Detects the on/off status of the lane departure alert system and sends a signal to the forward recognition camera. |
| Airbag ECU (Airbag Sensor Assembly) | Yawrate Sensor | Detects the yaw rate and sends a signal to the forward recognition camera. |
| Steering Sensor | ·
Sends the turning angle of the steering wheel to the forward recognition camera. ·
Sends a turn signal command to the combination meter assembly. |
|
| Turn Signal Switch | Sends a turn signal command to the steering sensor. | |
| Central Gateway ECU (Network Gateway ECU) | Relays the signal between the CAN communication buses. | |
| DLC3 | The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions. | |
OPERATION CONDITION
Operating Conditions of Lane Departure Alert Function
| Operation | Condition |
|---|---|
| Operating | The lane departure alert function is activated when all of the following conditions are met:
·
The LDA main switch is on. (When the LDA main switch is pressed to turn on the lane departure alert system, the LDA indicator illuminates in white.) ·
The vehicle speed is approximately 50 km/h (32 mph) or more. ·
Lane marker or lane boundary is detected. ·
No turn signal command is detected. ·
A system malfunction is not detected. |
| Suspended | The lane departure alert function is suspended when any one of the following conditions is met:
·
The vehicle speed is less than approximately 50 km/h (32 mph). ·
A turn signal command is detected. ·
No lane markers or lane boundaries are detected. ·
The yawrate sensor is malfunctioning. ·
The vehicle crosses halfway or further over a lane marker. ·
Immediately after the lane departure alert system is activated. ·
Detection of the curve radius other than regulated. ·
A malfunction is detected in the lane departure alert system. ·
The temperature of the forward recognition camera is abnormal. ·
Detection of the lane width other than regulated. |
| Canceled/Resume | The lane departure alert function is stopped when any one of the following conditions is met:
·
The LDA main switch is off. ·
The lane departure alert system is temporarily stopped. ·
The lane departure alert system is malfunctioning. ·
The ignition switch is turned off. The lane departure alert function resumes when the following conditions are met: ·
The conditions to start operation listed above returns to be satisfied. ·
The lane departure alert system condition returns to normal. ·
The ignition switch is turned off and ON again to ensure normal operation, after the lane departure alert system has been stopped by a system malfunction. |
Operating Conditions of Yaw Assist Function
| Operation | Condition |
|---|---|
| Operating | The yaw assist function is activated when all of the following conditions are met:
·
The LDA main switch is on. (When the LDA main switch is pressed to turn on the lane departure alert system, the LDA indicator illuminates in white.) ·
The vehicle speed is approximately 50 km/h (32 mph) or more. ·
Lane marker or lane boundary is detected. ·
No turn signal command is detected. ·
A system malfunction is not detected. ·
Yaw assist is turned "ON" via customized combination meter assembly settings. ·
Deceleration at or above a constant speed is not detected. ·
Steering operations to change the direction of vehicle travel are not performed. ·
Systems related to vehicle safety, such as the VSC and pre-collision system, do not operate. ·
Acceleration via operation of the accelerator pedal is not detected. |
| Suspended | The yaw assist function is suspended when any one of the following conditions is met:
·
The vehicle speed is less than approximately 50 km/h (32 mph). ·
A turn signal command is detected. ·
No lane markers or lane boundaries are detected. ·
The yawrate sensor is malfunctioning. ·
The vehicle crosses halfway or further over a lane marker. ·
Steering assist generated to change the direction of vehicle travel is detected. ·
If the steering angle speed reaches a certain amount. ·
Deceleration at or above a constant speed is detected. ·
Systems related to vehicle safety, such as the VSC and pre-collision system, operate. ·
Acceleration via operation of the accelerator pedal is detected. ·
Immediately after the lane departure alert system is activated. ·
Detection of the curve radius other than regulated. ·
A malfunction is detected in the lane departure alert system. ·
The temperature of the forward recognition camera is abnormal. ·
Detection of the lane width other than regulated. |
| Canceled/Resume | The yaw assist function is stopped when any one of the following conditions is met:
·
The LDA main switch is off. ·
The lane departure alert system is temporarily stopped. ·
The lane departure alert system is malfunctioning. ·
The ignition switch is turned off. ·
Yaw assist is turned "OFF" via customized combination meter assembly settings. The yaw assist function resumes when the following conditions are met: ·
The conditions to start operation listed above returns to be satisfied. ·
The lane departure alert system condition returns to normal. ·
The ignition switch is turned off and ON again to ensure normal operation, after the lane departure alert system has been stopped by a system malfunction. ·
Yaw assist is turned "ON" via customized combination meter assembly settings. |
Operating Conditions of Vehicle Sway Warning Function
| Operation | Condition |
|---|---|
| Operating | The vehicle sway warning function is activated when all of the following conditions are met:
·
Sway warning is turned "ON" via customized combination meter assembly settings. ·
The vehicle speed is approximately 50 km/h (32 mph) or more. ·
Lane markers are detected. ·
No turn signal command is detected. ·
A system malfunction is not detected. |
| Suspended | The vehicle sway warning function is suspended when any one of the following conditions is met:
·
The vehicle speed is less than approximately 50 km/h (32 mph). ·
One side of lane markers is not detected. ·
The yawrate sensor is malfunctioning. ·
Immediately after the lane departure alert system is activated. ·
Detection of the curve radius other than regulated. ·
A malfunction is detected in the lane departure alert system. ·
The temperature of the forward recognition camera is abnormal. ·
Detection of the lane width other than regulated. ·
A turn signal command is detected. |
| Canceled/Resume | The vehicle sway warning function is stopped when any one of the following conditions is met:
·
The lane departure alert system is temporarily stopped. ·
The lane departure alert system is malfunctioning. ·
The ignition switch is turned off. ·
Sway warning is turned "OFF" via customized combination meter assembly settings. The vehicle sway warning function resumes when the following conditions are met: ·
The conditions to start operation listed above returns to be satisfied. ·
The lane departure alert system condition returns to normal. ·
The ignition switch is turned off and ON again to ensure normal operation, after the lane departure alert system has been stopped by a system malfunction. ·
Sway warning is turned "ON" via customized combination meter assembly settings. |
SYSTEM CONTROL
Lane Departure Alert System Warning Operation
Function Overview (Lane Departure Alert Function)
If the lane departure alert system judges that the vehicle may deviate from the lane it is in, the lane departure alert system illuminates the indicator in the combination meter display and vibrates the steering wheel or sounds a buzzer so that the driver can take action to avoid lane departure.
This illustration is only for explanatory purposes.
Function Overview (Yaw Assist Function)
If the lane departure alert system judges that the vehicle may deviate from the lane it is in, the lane departure alert system performs yaw assist by operating the brakes of wheels on only one side of the vehicle to help the driver correct the path of the vehicle. If the driver does not take appropriate action, the lane departure alert system sounds a meter buzzer or vibrates the steering wheel.
The stop lights may not illuminate in some situations.
This illustration is only for explanatory purposes.
Function Overview (Vehicle Sway Warning Function)
The lane departure alert system detects drift of the vehicle within its lane, which is often the result of a driver who is tired, distracted or not looking ahead, based on the position of the vehicle within its lane and the steering inputs of the driver, to alert the driver before a lane departure or collision occurs.
The vehicle sway warning function provides a warning to alert the driver when any of the following conditions occur:
FUNCTION
The lane departure alert system can be turned on/off by pressing the LDA main switch on the steering pad switch assembly while the engine is started.
When the ignition switch is turned from off to ON, the lane departure alert system turns on.
| *a | LDA Main Switch | - | - |
Lane Departure Alert System Settings Functions Customization
| Item | Description | Setting |
|---|---|---|
| Yaw Assist | Select to enable/disable yaw assist | ·
ON ·
OFF |
| Alert | Warning method | ·
Buzzer ·
Steering Vibration |
| Sensitivity | Timing of the lane departure alert | ·
High ·
Standard |
| Sway Warning | Select to enable/disable the vehicle sway warning function | ·
ON ·
OFF |
| Sway Sensitivity | Timing of the vehicle sway warning function | ·
High ·
Standard ·
Low |
DIAGNOSIS
In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The DTCs of malfunctioning parts can be read by connecting the Global TechStream (GTS). Refer to the Repair Manual for details.