Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
NM35X0E _57 Power Source / Network _078502 NETWORKING _0381309 CAN COMMUNICATION SYSTEM GE GENERAL F

NETWORKING  CAN COMMUNICATION SYSTEM  GENERAL  GENERAL  


GENERAL


a.

Controller Area Network (CAN) communication, which makes high-speed communication possible, is used as a multiplex communication system* to simplify vehicle wire harnesses and achieve high-speed communication.

CAN Specifications
Protocol Specifications
Communication Speed 500 kbps
Communication Wire Twisted-pair Wire
Drive Type Differential Voltage Drive
Data Length 1 - 8 Byte (Variable)

HINT:

*: The multiplex communication system connects several ECUs together with one communication line so that they can exchange data with each other. As a result, additional wiring is not required when integrating systems and adding functions.



b.

Communication Wire

i.

A twisted pair of wires is used for CAN communication.

Communication Wire Outline
Twisted-pair Wire
Y120996

This communication wire is a pair of twisted wires. Communication is driven by applying different voltages to the 2 lines in order to send a single signal. The bus line has a high line (2.5 V to 3.5 V of voltage is applied) and a low line (1.5 V to 2.5 V of voltage is applied). This system, which is called a "differential voltage drive", reduces noise.

Y211516E02
1.813,1.333 2.177,1.531 0.365,0.198 10 false ECU 5.073,1.323 5.417,1.573 0.344,0.25 10 false ECU 3.094,1.531 4.292,1.833 1.198,0.302 10 false Twisted-pair Wire 2.865,2.156 4.458,2.521 1.594,0.365 10 false Differential Voltage Drive



c.

A CAN* communication system is used to send information and data for multiple items, which have been converted into digital signals by the communication circuit, over one communication line (twisted-pair wire). As a result, the communication systems connected to the input systems (such as sensors and switches), control units and output systems (such as motors), achieve simplified vehicle wire harnesses.

HINT:

*: CAN, an abbreviation of "Controller Area Network", is an ISO (International Organization for Standardization)-compliant serial communication.



d.

The CAN communication system consists of a pair of two communication lines (buses), CAN-High and CAN-Low. The system uses the differential voltage of the communication lines to determine the bus level* and transmits a digital signal at 500 kbps using an exclusive communication protocol (communication rules).

HINT:

*: The bus level has a dominant level and a recessive level, and the CAN communication system logically calculates the dominant level as "0" and the recessive level as "1".


Y212212E01
0.646,1.052 1.073,0.167 1.073,0.167 1.313,0.167 true 1.229,1 1.438,0.583 1.438,0.583 1.646,0.583 true 5.833,0.99 5.542,0.604 5.542,0.604 5.292,0.604 true 6.5,1.052 6.177,0.156 6.177,0.156 5.917,0.156 true 1.365,0.094 3.156,0.417 1.792,0.323 10 false CAN Communication Circuit 1.688,0.5 3.479,0.823 1.792,0.323 10 false ECU, Sensor 2.115,0.938 2.604,1.281 0.49,0.344 10 false CANH 2.135,1.51 2.625,1.854 0.49,0.344 10 false CANL 4.583,1.531 5.073,1.875 0.49,0.344 10 false CANH 4.646,0.948 5.135,1.292 0.49,0.344 10 false CANL 4.167,0.073 5.958,0.396 1.792,0.323 10 false CAN Communication Circuit 4.427,0.51 5.333,0.833 0.906,0.323 10 false ECU, Sensor 0.677,2.313 1.469,2.656 0.792,0.344 10 false Voltage [V] 1.49,2.542 1.604,2.719 0.115,0.177 10 false 4 1.479,2.792 1.594,2.969 0.115,0.177 10 false 3 1.49,3.021 1.604,3.198 0.115,0.177 10 false 2 1.49,3.229 1.604,3.406 0.115,0.177 10 false 1 0.333,4.125 1.125,4.469 0.792,0.344 10 false Bus Level 1.479,3.479 1.594,3.656 0.115,0.177 10 false 0 1.188,4 1.646,4.25 0.458,0.25 10 false HI="1" 1.167,4.271 1.667,4.521 0.5,0.25 10 false LO="0" 1.708,3.667 2.5,4.01 0.792,0.344 10 false Recessive 4.875,3.656 5.667,4 0.792,0.344 10 false Recessive 3.292,3.656 4.083,4 0.792,0.344 10 false Recessive 2.531,3.656 3.323,4 0.792,0.344 10 false Dominant 4.146,3.667 4.938,4.01 0.792,0.344 10 false Dominant 5.667,3.5 6,3.833 0.333,0.333 10 false Time 2.167,4.5 5.083,4.833 2.917,0.333 10 false CAN Bus Differential Voltage and Logical Value 0.5,5.083 2,5.417 1.5,0.333 10 false : CAN-High 0.5,5.417 2,5.75 1.5,0.333 10 false : CAN-Low


e.

The terminating resistors for each bus are located as shown in the following table.

Bus Terminating Resistor Location Gateway Function Gateway Destination

*1: Models without Supplemental Restraint System (SRS) airbag system

*2: Models with SRS airbag system

*3: Models with UREA Selective Catalytic Reduction (SCR) system

*4: Models with blind spot monitor system

*5: Models with Toyota Safety Sense

*6: Models with multimedia system or navigation system

Bus 1
·

No. 3 CAN Junction Terminal

·

Central Gateway ECU


Central Gateway ECU
·

To Bus 2

·

To Bus 3

·

To Bus 4

·

To Bus 5

·

To V Bus


Bus 2
·

Central Gateway ECU

·

ECM


Central Gateway ECU
·

To Bus 1

·

To Bus 3

·

To Bus 4

·

To Bus 5

·

To V Bus


Bus 3
·

Central Gateway ECU


Central Gateway ECU
·

To Bus 1

·

To Bus 2

·

To Bus 4

·

To Bus 5

·

To V Bus


Bus 4
·

Central Gateway ECU

·

No. 2 CAN Junction Terminal*1

·

Airbag ECU (Airbag Sensor Assembly)*2


Central Gateway ECU
·

To Bus 1

·

To Bus 2

·

To Bus 3

·

To Bus 5

·

To V Bus


Bus 5
·

Central Gateway ECU

·

Combination Meter Assembly


Central Gateway ECU
·

To Bus 1

·

To Bus 2

·

To Bus 3

·

To Bus 4

·

To V Bus


V Bus
·

Central Gateway ECU


Central Gateway ECU
·

To Bus 1

·

To Bus 2

·

To Bus 3

·

To Bus 4

·

To Bus 5


Local Bus*3
·

ECM

·

No. 1 CAN Junction Terminal


- -
Local Bus*4
·

Blind Spot Monitor Sensor RH

·

Blind Spot Monitor Sensor LH


- -
Local Bus*5
·

Millimeter Wave Radar Sensor Assembly

·

Forward Recognition Camera


- -
Local Bus*6
·

Radio and Display Receiver Assembly

·

Combination Meter Assembly


- -


f.

CAN Communication Protocol (Communication Rules)

i.

The CAN communication system is a type of multiplex communication system that uses one communication line for all devices that make up the network and makes it possible to send and receive data while offsetting the communication timing. In order to do so, communication is performed according to a communication protocol (communication rules) that is shared by the devices. This communication protocol helps communication be performed smoothly and securely.


ii.

The CAN communication protocol uses the Carrier Sense Multiple Access with Collision Detection (CSMA/CD) protocol* as the rules for sending data via the communication line. This protocol allows all devices to share one communication line while retaining the right to start sending data.

HINT:

*: This is a type of communication access control where devices constantly detect the condition of the communication line and only send data when no other data is being sent. In addition, when the system detects that a data collision has occurred (data was simultaneously sent from another device), it waits for a certain period of time before resending the data.



iii.

Data used by the CAN communication system is composed of a single frame that includes parts such as "ID", "DLC", "DATA", "CRC" and "ACK".

Y212213E01
1.333,1.208 1.333,0.167 1.333,0.167 1.583,0.167 true 1.667,1.542 1.667,0.5 1.667,0.5 1.917,0.5 true 2.833,1.417 2.833,0.5 2.833,0.5 3.083,0.5 true 3.25,1.5 3.25,1 3.25,1 3.5,1 true 4.833,2.917 4.583,2.917 4.583,2.917 4.583,1.667 true 6.333,2.167 6.5,2.167 6.5,2.167 6.5,1.75 true 0.479,1.333 1,1.521 0.521,0.188 10 false HI = "1" 0.479,1.729 1.083,1.917 0.604,0.188 10 false LO = "0" 1.26,1.583 1.427,1.854 0.167,0.271 10 false 1 1.75,1.583 2.083,1.917 0.333,0.333 10 false 11 2.375,1.563 2.542,1.833 0.167,0.271 10 false 1 2.5,1.563 2.667,1.833 0.167,0.271 10 false 1 2.615,1.563 2.781,1.833 0.167,0.271 10 false 1 2.854,1.583 3.188,1.917 0.333,0.333 10 false 4 1.75,1.417 2.083,1.75 0.333,0.333 10 false ID 2.771,1.417 3.104,1.75 0.333,0.333 10 false DLC 3.583,1.417 4.083,1.75 0.5,0.333 10 false DATA 5.083,1.417 5.583,1.75 0.5,0.333 10 false CRC 5.167,1.583 5.5,1.917 0.333,0.333 10 false 15 5.167,1.583 5.5,1.917 0.333,0.333 10 false 15 5.906,1.563 6.073,1.833 0.167,0.271 10 false 1 6.01,1.563 6.177,1.833 0.167,0.271 10 false 1 6.125,1.563 6.292,1.833 0.167,0.271 10 false 1 6.5,1.594 6.667,1.865 0.167,0.271 10 false 7 1.188,1.219 1.521,1.552 0.333,0.333 10 false SOF 6,1.25 6.333,1.583 0.333,0.333 10 false ACK 1.146,2.083 2.333,2.5 1.188,0.417 10 false Control Information (Fixed Values) 3.333,1.833 4.854,2.083 1.521,0.25 10 false 0 - 64 (Variable) 3.25,2.25 3.917,2.5 0.667,0.25 10 false Time 1.667,0.083 2.5,0.417 0.833,0.333 10 false Data Head 2,0.427 2.833,0.76 0.833,0.333 10 false Data ID 3.167,0.417 4,0.75 0.833,0.333 10 false Data Length 3.583,0.917 4.417,1.25 0.833,0.333 10 false Data Content 3.208,2.833 4.042,3.167 0.833,0.333 10 false Data Frame 4.896,2.833 6.396,3.083 1.5,0.25 10 false Error Detection Code 5.469,0.198 6.802,0.781 1.333,0.583 10 false Response from ECU which Receives Data 6.417,1.427 6.75,1.76 0.333,0.333 10 false EOF 4.667,2.083 6.333,2.5 1.667,0.417 10 false Communication Complete 0.063,3.333 6.417,3.667 6.354,0.333 10 false Note: The numbers in the frame indicate the number of bits used to send information.



g.

A diagnostic tool can be connected to perform diagnostic communication. Refer to the Repair Manual for details.