OUTLINE
An automatic air conditioning system, a manual air conditioning system, a manual cooler system, a manual heater system or a boost vent system is used depending on the model.
The automatic air conditioning system uses neural network control to enhance comfort.
An inside-and-outside dual air layer type air conditioning unit is used. The upper layer ensures anti fogging performance by introducing outside air, and the lower layer aims for ventilation loss reduction by circulating the inside air, achieving energy conservation.*
A manual rear cooler system is used depending on the model.
A manual rear heater system is used depending on the models.
*: Models with inside-and-outside dual air layer type air conditioning unit
SPECIFICATIONS
Front Air Conditioning System, Front Heater System, Front Cooler System or Boost Vent System
| Component | Specifications | |
|---|---|---|
|
*1: Upper side *2: Lower side *3: Models with 7GR-FKS engine *4: Models with 1GD-FTV-engine *5: Models without manual rear cooler system *6: Models with manual rear cooler system |
||
| Heater Radiator Unit Sub-assembly | Type | Straight Flow Aluminum-II (SFA-II) |
| Size (W x H x L) | 222.3 mm x 120 mm x 27 mm
(8.75 in. x 4.72in. x 1.06in.) |
|
| Fin Pitch | 1.8 mm (0.0709 in.) | |
| Blower Motor with Fan Sub-assembly | Motor Type | DC Ferrite Brushless |
| Fan Type | Sirocco | |
| Fan Size (Dia. x H) | 122 mm x 55 mm (4.80 in. x 2.17 in.)*1
125 mm x 38 mm (4.92 in. x 1.50 in.)*2 |
|
| Cooler Condenser Assembly | Type | Global Inner-fin Condenser (GIC) |
| Size (W x H x L) | 690 mm x 504.2 mm x 11.5 mm*3
(27.2 in. x 19.9 in. x 0.453 in.)*3 690 mm x 382.6 mm x 11.5 mm*4 (27.2 in. x 15.1 in. x 0.453 in.)*4 |
|
| Fin Pitch | 3.0 mm (0.118 in.) | |
| Cooler Compressor Assembly | Type | 10SRE15C*5
10SRE18C*6 |
| Refrigerant | Type | HFC-134a (R-134a) |
| No. 1 Cooler Evaporator Sub-assembly | Type | Beneficial Refrigerant Stream (BRS) |
| Size (W x H x L) | 239.5 mm x 231 mm x 38 mm
(9.43 in. x 9.09 in. x 1.50 in.) |
|
| Fin Pitch | 3.0 mm (0.118 in.) | |
| Component | Specifications | ||
|---|---|---|---|
| Manual Air Conditioning System | Manual Cooler System | ||
|
*1: Models with GIC type condenser *2: Models with MF-IV type condenser *3: Models with 7GR-FKS engine *4: Models with 1GD-FTV-engine *5: Models without manual rear cooler system *6: Models with manual rear cooler system *7: Models without stop and start system *8: Models with stop and start system |
|||
| Heater Radiator Unit Sub-assembly | Type | Straight Flow Aluminum-II (SFA-II) | - |
| Size (W x H x L) | 222.3 mm x 120 mm x 27 mm
(8.75 in. x 4.72 in. x 1.06 in.) |
- | |
| Fin Pitch | 1.8 mm (0.0709 in.) | - | |
| Blower Motor with Fan Sub-assembly | Motor Type | K70 | |
| Fan Type | Semi-sirocco | ||
| Fan Size (Dia. x H) | 137 mm x 70 mm (5.39 in. x 2.76 in.) | ||
| Cooler Condenser Assembly | Type | Global Inner-fin Condenser (GIC)*1
Multi-Flow IV (MF-IV) Sub-cool*2 |
|
| Size (W x H x L)*1 | 690 mm x 504.2 mm x 11.5 mm (27.2 in. x 19.9 in. x 0.453 in.)*3
690 mm x 382.6 mm x 11.5 mm (27.2 in. x 15.1 in. x 0.453 in.)*4 |
||
| Size (W x H x L)*2 | 696 mm x 504.6 mm x 22 mm (27.4 in. x 19.9 in. x 0.866 in.)*3
696 mm x 389.4 mm x 22 mm (27.4 in. x 15.3 in. x 0.866 in.)*4 |
||
| Fin Pitch | 3.0 mm (0.118 in.)*1
3.1 mm (0.122 in.)*2 |
||
| Cooler Compressor Assembly | Type | 10SRE15C*5
10SRE18C*6 |
|
| Refrigerant | Type | HFC-134a (R-134a) | |
| No. 1 Cooler Evaporator Sub-assembly | Type | Beneficial Refrigerant Stream (BRS)*7
Cold Storage (CS)*8 |
|
| Size (W x H x L) | 239.5 mm x 231 mm x 38 mm (9.43 in. x 9.09 in. x 1.50 in.) | ||
| Fin Pitch | 3.0 mm (0.118 in.) | ||
| Component | Specifications | ||
|---|---|---|---|
| Manual Heater System | Boost Vent System | ||
|
*: The No. 1 cooler evaporator sub-assembly has been provided, but is not used. |
|||
| Heater Radiator Unit Sub-assembly | Type | Straight Flow Aluminum-II (SFA-II) | - |
| Size (W x H x L) | 222.3 mm x 120 mm x 27 mm
(8.75x 4.72in. x 1.06in.) |
- | |
| Fin Pitch | 1.8 mm (0.0709 in.) | - | |
| Blower Motor with Fan Sub-assembly | Motor Type | K70 | |
| Fan Type | Semi-sirocco | ||
| Fan Size (Dia. x H) | 137 mm x 70 mm (5.39 in. x 2.76 in.) | ||
| No. 1 Cooler Evaporator Sub-assembly* | Type | Beneficial Refrigerant Stream (BRS) | |
| Size (W x H x L) | 239.5 mm x 231 mm x 38 mm (9.43 in. x 9.09 in. x 1.50 in.) | ||
| Fin Pitch | 3.0 mm (0.118 in.) | ||
Rear Cooler System (Models with Manual Rear Cooler System)
| Component | Specifications | |
|---|---|---|
| Evaporator Sub-assembly (Rear) | Type | Beneficial Refrigerant Stream (BRS) |
| Size (W x H x L) | 293.1 mm x 151 mm x 38 mm
(11.54 in. x 5.94 in. x 1.50 in.) |
|
| Fin Pitch | 3.0 mm (0.118 in.) | |
| Rear Blower Motor with Fan Sub-assembly | Motor Type | K62 |
| Fan Type | Semi-sirocco | |
| Fan Size (Dia. x H) | 145 mm x 55 mm (5.71 in. x 2.17 in.) | |
Rear Heater System (Models with Manual Rear Heater System)
| Component | Specifications | |
|---|---|---|
| Rear Heater Unit Sub-assembly | Type | Straight Flow Aluminum-II (SFA-II) |
| Size (W x H x L) | 149.5 mm x 150 mm x 27 mm
(5.89 in. x 5.91 in. x 1.06 in.) |
|
| Fin Pitch | 1.8 mm (0.0709 in.) | |
| Rear Blower Motor Sub-assembly | Motor Type | S70F |
| Fan Type | Semi-sirocco | |
| Fan Size (Dia. x H) | 120 mm x 70 mm (4.72 in. x 2.76 in.) | |
MAIN FEATURES
The air conditioning system has the following features:
| Feature | Outline |
|---|---|
|
*1: Models with automatic air conditioning system *2: Models with rear passenger side air duct *3: Models without manual rear cooler system *4: Models with manual rear cooler system *5: Models without stop and start system *6: Models with stop and start system *7: Models with automatic air conditioning system, manual air conditioning system or manual heater system *8: Models with GIC type condenser *9: Models with MF-IV type condenser |
|
| High Performance | ·
Neural network control is used, so passengers can finely control the air conditioning for maximum comfort.*1 ·
The rear outlets are installed on the back of the center console and back of the seat leg cover to ensure comfortable air conditioning performance for the rear passengers.*2 ·
The blower control has 7 levels in manual mode and 31 levels in auto mode for more precise control.*1 ·
The rear cooling unit assembly is available on depending on the model. ·
A clean air filter (air refiner element) is used. |
| Light Weight*1 | ·
A bus connector with a built-in IC is used in a lightweight wire harness design to allow a reduced number of wires. ·
The use of this connector means that pulse pattern type servo motors can be used. |
| Compact*1 | A blower motor with a built-in blower motor controller is used to achieve a compact construction for the front air conditioning system. |
| Others | The following parts are used to ensure high cooling performance while achieving a compact and lightweight construction:
·
Semi-center Location Air Conditioning Unit ·
10SRE15C Type Compressor*3 ·
10SRE18C Type Compressor*4 ·
Beneficial Refrigerant Stream (BRS) Evaporator*5 ·
Cold Storage (CS) Evaporator*6 ·
Straight Flow Aluminum (SFA)-II Heater Radiator Sub-assembly*7 ·
Global Inner-fin Condenser (GIC)*8 ·
Multi-Flow IV (MF-IV) Sub-cool Condenser*9 |