FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
|
*1: Models with rear wiper system *2: Models with vehicle speed-sensing, adjustable interval function *3: Models with VSC *4: Models without VSC |
||
| Windshield Wiper Motor Assembly | Operates the wipers according to control performed by the windshield wiper relay assembly. | |
| Rear Wiper Motor Assembly*1 | RR Wiper Motor | Operates the rear wipers according to control performed by the RR wiper relay. |
| RR Wiper Relay*1 | Receives rear wiper operation request signals from the main body ECU and operates the RR wiper motor. | |
| Windshield Wiper Relay Assembly | ·
Receives front washer or rear washer*1 spray request signals from the main body ECU and operates the windshield washer motor and pump assembly. ·
Receives front wiper operation request signals from the main body ECU and operates the windshield wiper motor assembly. |
|
| Windshield Washer Jar Sub-assembly | Windshield Washer Motor and Pump Assembly | Activates in accordance with the signal from the windshield wiper relay assembly. |
| Main Body ECU (Multiplex Network Body ECU) | ·
Receives information from ECUs and sensors and sends front wiper operation request signals to the windshield wiper relay assembly. ·
Receives information from ECUs and sensors and sends washer pump operation request signals to the windshield wiper relay assembly. ·
Receives information from ECUs and sensors and sends rear wiper operation request signals to the RR wiper relay.*1 |
|
| Windshield Wiper Switch Assembly | FR Wiper Control Switch | Sends the switch position signal to the steering sensor*3 or combination switch ECU sub-assembly*4. |
| RR Wiper Control Switch*1 | ||
| FR Washer Switch | ||
| RR Washer Switch*1 | ||
| Interval Time Adjuster*2 | ||
| Steering Sensor*3 | Sends the FR wiper control switch, RR wiper control switch*1, FR washer switch, RR washer switch*1 and interval time adjuster position*2 signal to the main body ECU. | |
| Combination Switch ECU Sub-assembly*4 | ||
| Combination Meter Assembly | Sends the vehicle speed signal to the main body ECU. | |
| ECM | Sends the shift position signal to the main body ECU. | |
| Skid Control ECU | Sends the vehicle speed signal to the combination meter assembly. | |
| Central Gateway ECU (Network Gateway ECU) | Relays signals between the CAN communication lines. | |
| DLC3 | The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions. | |
FUNCTION
Mist Function
When the MIST switch (wiper control switch) is on, the wipers operate at LO.
Washer-linked Wiper with Drip-prevention Function
When the washer switch is turned on with the windshield wiper switch assembly set to off or AUTO, the washer fluid sprays simultaneously. Once the washer switch is on for approximately 0.3 seconds or more, the wipers starts on LO approximately 0.2 seconds later.
When the washer switch is on, the wipers operate at a speed lower than LO.
If the washer switch is turned off before one complete wiper operation is performed, the wipers operate 2 times on LO.
If the washer switch is turned off after at least one complete wiper operation is performed, the wipers operate 3 times on LO.
When the washer switch is turned on for approximately 0.5 seconds or more and the vehicle speed is approximately 7 km/h (4 mph) or less, the wipers operate once more after the end of this operation as shown in the following diagram.
Vehicle Speed-Sensing, Adjustable Interval Function (Models with Vehicle Speed-Sensing, Adjustable Interval Function)
When the windshield wiper switch is in the INT position, the interval time of the wiper is controlled in 3 stages in accordance with the automatic control adjuster position and the vehicle speed.
The interval time can be controlled steplessly within each range.
Vehicle Speed Switching Function (Models with Vehicle Speed-Sensing, Adjustable Interval Function)
When the windshield wiper switch is in the LO position and the vehicle stops moving, wiper operation is automatically switched to intermittent operation.
If the wiper control switch is changed from a position other than LO* to LO while the vehicle is stopped, the wipers operate 3 times, and then automatically switch to intermittent operation (the wipers operate at approximately 2.5-second intervals). Also, when the automatic control adjuster position is FAST, the wipers operate on LO even while the vehicle is stopped.
*: Except OFF
When the vehicle stops moving and the windshield wiper switch assembly is in the LO position, the wipers operate twice in LO. It then switches to intermittent operation with an interval time of approximately 2.5 seconds. If the vehicle starts moving during this intermittent wiper operation, the wiper automatically returns to LO operation. Also, when the automatic control adjuster position is FAST, the wipers operate on LO even while the vehicle is stopped.