Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
NM35X0E _59 Vehicle Exterior _078579 WIPER / WASHER _0382011 WIPER AND WASHER SYSTEM DE DETAILS F

WIPER / WASHER  WIPER AND WASHER SYSTEM  DETAILS  WIPER BLADE  


CONSTRUCTION


a.

FR Wiper Blade

i.

A fin-shaped resin cover is provided for the entire wiper blade, achieving a sharp look with a high-quality feel to improve appearance.


ii.

The wiper blade length is 600 mm (23.6 in.) for the driver side and 500 mm (19.7 in.) for the front passenger side. Superior forward visibility is ensured by the increased sweep range.


iii.

The blade rubber surface is coated with graphite to reduce the impulsive noise that occurs when the blades operate in reverse and increase the lifespan of the blade rubber.

Y237492C01
5.51,1.521 4.688,0.75 4.688,0.75 5.219,1.51 true 5.365,1.604 5.885,1.802 true 0.927,0.771 1.427,0.406 1.427,0.406 1.333,1.021 true 2.229,1.531 2.74,0.938 2.74,0.938 2.635,1.781 true 5.771,0.646 6.24,0.5 true 5.563,1.313 6.375,1.563 true 4.688,2.219 5.208,2.021 true 3.063,1.521 3.219,1.719 0.156,0.198 10 false A 2.188,1.927 2.344,2.125 0.156,0.198 10 false A 5.917,1.76 6.115,1.969 0.198,0.208 10 false *d 6.406,1.531 6.615,1.729 0.208,0.198 10 false *c 6.281,0.396 6.51,0.594 0.229,0.198 10 false *a 4.552,0.594 4.781,0.792 0.229,0.198 10 false *b 2.677,0.76 2.99,0.958 0.313,0.198 10 false *a 1.385,0.229 1.698,0.427 0.313,0.198 10 false *a 4.531,2.167 4.729,2.375 0.198,0.208 10 false *e 5.302,2.281 5.5,2.49 0.198,0.208 10 false *f
*a Cover *b Backing Plate
*c Lever *d Plate Rubber
*e Graphite Coating *f A - A Cross Section




b.

RR Wiper Blade (Models with Rear Wiper System)

i.

Resin is used for the RR wiper arm and blade assembly to achieve weight reduction.


ii.

The RR wiper blade length is 400 mm (15.7 in.).

Y243077C01
0.333,0.99 0.417,0.49 true 3.406,2.396 3.302,2.021 true 4.969,1.917 5.125,1.344 true 5.677,1.438 5.875,0.615 true 6.188,1.229 6.719,1.094 true 6.167,1.844 6.563,2.021 true 0.24,1.021 0.552,1.177 0.313,0.156 10 false *a 5.813,0.469 6.125,0.625 0.313,0.156 10 false *b 4.875,1.938 5.188,2.094 0.313,0.156 10 false *c 6.594,1.99 6.906,2.146 0.313,0.156 10 false *d 3.323,2.438 3.635,2.594 0.313,0.156 10 false *a 6.74,1.031 7.052,1.188 0.313,0.156 10 false *a
*a Holding Claw *b Backing Plate
*c Lever *d Plate Rubber