CONSTRUCTION
Segment LCD Monitor Type Multi-information Display
Display Item
The multi-information display is located at the right of the combination meter assembly.
The multi-information display indicates as follows:
| Area | Item | Outline |
|---|---|---|
|
*1: Models with Toyota parking assist-sensor system *2: Models with automatic transmission |
||
| *a | Clock | The current time is displayed. |
| *b | Outside Temperature Gauge | ·
The outside temperature is displayed. ·
When the outside temperature drops below 3°C (37°F), an ice warning indicator illuminates to warn the driver to drive with caution due to possibly icy road conditions. After the ice warning indicator flashes 10 times, the indicator stays on. When the temperature reaches 5°C (41°F), the indicator goes off. |
| *c | Toyota Parking Assist-sensor System Detection Display*1 | The detection location and the approximate distance to the stationary object are displayed. |
| *d | Cruise Information Display | The following information can be displayed:
·
Odometer ·
Trip Meter A ·
Trip Meter B ·
Current Fuel Consumption ·
Total Average Fuel Consumption ·
Cruising Range ·
Average Vehicle Speed ·
Dimming Mode Display ·
Customization Mode Display*2 |
| *e | ECO Driving Indicator Zone Display*2 | How much the vehicle is being driven in an eco-friendly manner is displayed with a bar graph. |
| *f | Water Temperature Gauge | The engine coolant temperature date are displayed with bar graph. |
| *g | Shift Position Indicator*2 | The current shift position is displayed. |
Cruise Information Display
The cruise information display can be switched by operating the DISP and ODO/TRIP switch. The counter can be reset by pressing and holding the DISP and ODO/TRIP switch for 0.8 seconds or more.
| *A | Models with Automatic Transmission | - | - |
| *a | Odometer | *b | Trip Meter A |
| *c | Trip Meter B | *d | Current Fuel Consumption |
| *e | Total Average Fuel Consumption | *f | Cruising Range |
| *g | Average Vehicle Speed | *h | Dimming Mode Display |
| *i | Customization Mode Display
·
Eco Driving Indicator Setting |
- | - |
|
The DISP and ODO/TRIP switch is operated for less than 0.8 seconds. |
|
The DISP and ODO/TRIP switch is operated for 0.8 seconds or more to reset. |
|
The DISP and ODO/TRIP switch is operated for 0.8 seconds or more to change active or inactive. |
|
The DISP and ODO/TRIP switch is operated for 0.8 seconds or more to customize mode display. |
| Display | Outline | |
|---|---|---|
| Current Fuel Consumption |
|
·
Displays the value that has been calculated by the meter ECU, which is based on the driven distance and the fuel consumption volume (fuel injection amount signal from the ECM via CAN), provided that the ignition switch is turned ON. ·
The display updates every 0.5 seconds. |
| Total Average Fuel Consumption |
|
·
Displays the value that has been calculated by the meter ECU, which is based on the driven distance and the fuel consumption volume (fuel injection amount signal from the ECM via CAN) since the counter was reset. ·
The display updates every 10 seconds. |
| Cruising Range |
|
·
Displays the value that has been calculated by the meter ECU, which is based on the fuel consumption data that the meter ECU continuously monitors and stores in its memory, and the residual fuel volume data, provided that the ignition switch is turned ON. ·
The display updates every 10 seconds. |
| Average Vehicle Speed |
|
·
Displays the value that has been calculated by the meter ECU, which is based on the elapsed time and driven distance since the ignition switch was turned ON. ·
The display updates every 10 seconds. |
| Dimming Mode Display |
|
Displays the combination meter brightness. |
TFT LCD Monitor Type Multi-information Display
Display Item
The multi-information display is located at the center of the combination meter assembly.
The multi-information display has 5 dedicated areas.
The multi-information display shows the following information:
| Area | Item | Outline |
|---|---|---|
|
*1: Models with cruise control system *2: Models with speed limiter system *3: Models with lane departure alert system *4: Models with road sign assist system *5: Models with automatic transmission *6: Models with iMT system *7: Models with Toyota Safety Sense or navigation system *8: Models with multimedia system or navigation system |
||
| *a | Driving Support System Information | The operation condition of the following items is displayed:
·
Cruise Control System*1 ·
Speed Limiter System*2 ·
Lane Departure Alert System*3 ·
Road Sign Assist System*4 |
| *b | Indicator | When the illumination conditions are met, the following indicators illuminate:
·
LDA Indicator*3 ·
Eco Driving Indicator*5 ·
iMT Indicator*6 |
| *c | Clock | The current time is displayed. |
| Outside Temperature Gauge | ·
The outside temperature is displayed. ·
When the outside temperature drops below 3°C (37°F), an ice warning indicator illuminates to warn the driver to drive with caution due to possibly icy road conditions. After the ice warning indicator flashes 10 times, the indicator stays on. When the temperature reaches 5°C (41°F), the indicator goes off. |
|
| Tab Icons | Displays the tab selected. | |
| *d | Information | ·
The following information can be displayed on the multi-information display by switching the tabs: -
Fuel Economy Information Tab -
Driving Assist System Information Tab*7 -
Audio Information Tab*8 -
Vehicle Information Tab -
Settings Tab -
Warning Message Tab ·
When a warning message request is received, an interrupt screen is displayed. |
| *e | ODO/TRIP Meter | ·
The odometer, trip meter A or trip meter B is displayed. ·
The item shown can be switched by pressing the ODO/TRIP switch. |
| Light Control Rheostat | Meter panel luminance can be changed by using the ODO/TRIP switch. | |
| Shift Position Indicator*5 | The current shift position is displayed. | |
The each tab shows the following information:
| Tab | Outline |
|---|---|
|
*1: Models with automatic transmission *2: Models with lane departure alert system *3: Models with road sign assist system *4: Models with navigation system *5: Models without multimedia system or navigation system *6: Models with Toyota Safety Sense *7: Models with blind spot monitor system *8: Models with Toyota parking assist-sensor system *9: Models with RCTA function *10: Models with stop and start system |
|
| Fuel Economy Information Tab | The following items can be displayed:
·
Digital Speedometer Display -
Vehicle Speed -
Driving Range ·
Fuel Consumption Graph -
Driving Range -
Current Fuel Consumption -
Fuel Consumption (1)
After Start (2)
After Reset (3)
After Refuel ·
ECO Driving Indicator Zone Display*1 -
ECO Driving Indicator Zone Display -
Driving Range |
| Driving Assist System Information Tab | The operation condition of the following items is displayed.
·
Lane Departure Alert System*2 ·
Road Sign Assist System*3 ·
Navigation System*4 |
| Audio Information Tab | Audio information (status information) is displayed and the audio source and songs can be switched. |
| Vehicle Information Tab | The following items can be displayed:
·
Drive Information -
Trip (After Start) (1)
Average Vehicle Speed (2)
Distance Travelled (3)
Elapsed Time -
Total (After Reset) (1)
Average Vehicle Speed (2)
Distance Travelled (3)
Elapsed Time |
| Settings Tab | The following settings can be changed:
·
Clock*5 ·
Lane Departure Alert System*2 ·
Pre-Collision System*6 ·
Blind Spot Monitor System*7 ·
Toyota parking assist-sensor system*8 ·
RCTA function*9 ·
Road Sign Assist System*3 ·
Vehicle Settings*10 ·
Meter Settings |
| Warning Message Tab | Warning messages about vehicle malfunctions are displayed. |
Display Function Flow
The multi-information display can be switched as shown in the flow chart below:
| *A | Models with Toyota Safety Sense or Navigation System |
| *B | Models with Multimedia System or Navigation System |
| *a | Conditions are not met. |
| *b | Conditions are met. |
| *c | If there are multiple display requests, items will be displayed in sequence. |
| *d | Item or display is selected by operating the steering pad switch assembly. |
| *e | ODO display is displayed for a certain period of time after the ignition switch is turned off. |
Display Tab Operation
The information currently displayed can be switched using the left/right switch of the steering pad switch assembly.
| *A | Models with Toyota Safety Sense or Navigation System | *B | Models with Multimedia System or Navigation System |
| *1 | Fuel Economy Information Tab | *2 | Driving Assist System Information Tab |
| *3 | Audio Information Tab | *4 | Vehicle Information Tab |
| *5 | Settings Tab | *6 | Warning Message Tab |
| *a | The illustration shown is example only. The illustration may differ from the actual vehicle screen. | - | - |
|
Left switch operation |
|
Right switch operation |
Fuel Economy Information
The fuel economy information shows vehicle information such as vehicle speed, drivable range and fuel consumption.
The fuel economy information can be switched using the up/down switch on the steering pad switch assembly.
| *A | Models with Automatic Transmission | - | - |
| *1 | Digital Speedometer Display | *2 | Fuel Consumption Graph |
| *3 | ECO Driving Indicator Zone Display | - | - |
| *a | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. | - | - |
|
Up Switch Operation |
|
Down Switch Operation |
Driving Assist System Information
The driving assist system information shows operation condition of the driving support system or navigation system.
The driving assist system information can be switched using the up/down switch on the steering pad switch assembly.
| *A | Models with Toyota Safety Sense | *B | Models with Navigation System |
| *1 | Driving Support System Information | *2 | Navigation System Information |
| *a | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. | - | - |
|
Up Switch Operation |
|
Down Switch Operation |
Setting Function
The items displayed on the multi-information display can be customized.
The following items can be selected on the information setting screen.
| Item | Available Setting |
|---|---|
| On the hour setting | Sets the minute display to "00" via the enter switch on the steering pad switch.
|
| Clock | Select to adjust clock of the combination meter. |
| Item | Available Setting | |
|---|---|---|
| LDA | Yaw Assist | Setting for yaw assist can be set to on/off:
·
ON ·
OFF |
| Alert | Warning method can be changed:
·
Steering wheel vibration (Icon is displayed) ·
Buzzer (Icon is displayed) |
|
| Sensitivity | Sensitivity of alert system can be changed:
·
High (Icon is displayed) ·
Standard (Icon is displayed) |
|
| Sway Warning | Sway warning function can be set to on/off:
·
ON ·
OFF |
|
| Sway Sensitivity | Sway warning sensitivity can be selected:
·
High (Icon is displayed) ·
Standard (Icon is displayed) ·
Low (Icon is displayed) |
|
| Item | Available Setting | |
|---|---|---|
| PCS | The pre-collision system can be set to on/off:
·
ON ·
OFF |
|
| Sensitivity | Pre-collision system warning sensitivity can be selected:
·
Early (Icon is displayed) ·
Middle (Icon is displayed) ·
Late (Icon is displayed) |
|
| Item | Available Setting | |
|---|---|---|
| BSM | The blind spot monitor system can be set to on/off:
·
ON ·
OFF |
|
| Brightness | Brightness of the outer rear view mirror indicator light can be changed:
·
Bright (Icon is displayed) ·
Dim (Icon is displayed) |
|
| Item | Available Setting | |
|---|---|---|
| Toyota Parking Assist-sensor System | Volume | The volume of the warning buzzer can be selected:
·
1 (Quiet) (Icon is displayed) ·
2 (Medium) (Icon is displayed) ·
3 (Loud) (Icon is displayed) |
| Item | Available Setting | |
|---|---|---|
| RCTA | The RCTA function can be set to on/off:
·
ON ·
OFF |
|
| Volume | The volume of the warning buzzer can be selected:
·
1 (Quiet) (Icon is displayed) ·
2 (Medium) (Icon is displayed) ·
3 (Loud) (Icon is displayed) |
|
| Item | Available Setting | |
|---|---|---|
| RSA | The road sign assist system can be set to on/off:
·
ON ·
OFF |
|
| Notification Method | Notification method can be selected:
·
Above Speed Limit: (a)
No Notification (b)
Only visual (c)
Visual & Audio |
|
| Notification Level | Excess speed notification level can be selected:
·
5 km/h ·
3 km/h ·
1 km/h |
|
| Item | Available Setting | |
|---|---|---|
|
*: Models with stop and start system |
||
| Stop and Start System* | Duration | The idling stop time of stop and start system can be selected:
·
Standard ·
Extended |
| Item | Available Setting | |
|---|---|---|
|
*1: Models with automatic transmission *2: Models with multimedia system or navigation system *3: Models with navigation system *4: Models with voice recognition system *5: Models with stop and start system |
||
| Language | The language used on the multi-information display can be selected:
·
Arabic ·
Thai ·
German ·
English ·
Spanish ·
French ·
Italian ·
Dutch ·
Portuguese ·
Portuguese in Brazil ·
Russian ·
Finnish ·
Turkish ·
Ukrainian ·
Hebrew ·
Malay ·
Indonesian ·
Korean ·
Traditional Chinese ·
Vietnamese
|
|
| Units | The unit displayed on the multi-information display can be selected:
·
km (km/L) ·
km (L/100 km) ·
miles (MPG)
|
|
| Eco Driving Indicator*1 | The Eco driving indicator can be set to on/off:
·
ON ·
OFF |
|
| Fuel Economy Information Tab | Fuel Economy | The fuel economy type can be selected:
·
Trip Average ·
Total Average ·
Tank Average |
| Audio Information Tab*2 | The audio information tab can be set to on/off:
·
ON ·
OFF |
|
| Vehicle Information Tab | Drive Info Type | The drive information type can be selected:
·
Trip ·
Total |
| Drive Info Items | The upper and lower of drive information items can be selected:
·
Average Speed ·
Distance ·
Elapsed Time |
|
| Pop-Up Display | The following displays that appear as soon as the set conditions are met can be switched to on/off:
·
Turn-by-turn Navigation*3 ·
Telephone*2 ·
Audio Operation*2 ·
Volume Operation*2 ·
Voice Control*4 ·
Duration*5 ·
Status*5 ·
Adjust Brightness |
|
| Multi-information Display OFF | Multi-information display is turned off. | |
| Default Settings | The set items can be initialized. | |
Interruption Display
When a warning is necessary, the warning message interrupts the current display on the multi-information display.
A warning message is displayed via an interrupt display when a vehicle malfunction occurs to warn the driver. Also, an advice message is displayed via an interrupt display depending on the situation, such as when the driver must proceed with caution.
The buzzer in the combination meter assembly may sound depending on the item displayed on the multi-information display.
The intersection guidance*1, telephone display*2, audio operation and volume operation displays*2 are linked with the multimedia system or navigation system*2 and displayed via an interrupt display.
*1: Models with navigation system
*2: Models with multimedia system or navigation system
The combination meter assembly displays the following messages based on signals received from the ECM.
| Message | Buzzer |
|---|---|
|
*1: Models with 1GD-FTV engine *2: Models with automatic transmission and models with VSC |
|
| REPLACE FUEL FILTER*1 | - |
| Release Accelerator
(and image display)*2 |
Sounds |
| Check Engine Visit Your Dealer | Sounds |
| Check Engine Reduced Engine Power Visit Your Dealer | Sounds |
| Reduced Engine Power Visit Your Dealer | Sounds |
| Engine Maintenance Required Visit Your Dealer | Sounds |
| Engine Coolant Temp High Stop in a Safe Place See Owner's Manual
(and image display) |
Sounds |
| Drive-Start Control Malfunction Visit Your Dealer
(and image display)*2 |
Sounds |
| Brake Override Malfunction Visit Your Dealer
(and image display) |
Sounds |
| Accelerator and Brake Pedals Pressed Simultaneously
(and image display) |
- |
The combination meter assembly displays the following messages based on signals received from the engine oil pressure switch assembly.
| Message | Buzzer |
|---|---|
| Oil Pressure Low Stop in a Safe Place See Owner's Manual
(and image display) |
Sounds |
The combination meter assembly displays the following messages based on signals received from the sedimenter level warning switch.
| Message | Buzzer |
|---|---|
|
*: Models with 1GD-FTV engine |
|
| Water Accumulation in Fuel Filter See Owner's Manual* | Sounds |
The combination meter assembly displays the following messages based on signals received from the engine oil level sensor.
| Message | Buzzer |
|---|---|
| Engine Oil Level Low Add or Replace | - |
The combination meter assembly displays the following messages based on signals received from the fuel sender gauge assembly.
| Message | Buzzer |
|---|---|
| Fuel Low | - |
The combination meter assembly displays the following messages based on signals received from the ECM.
| Message | Buzzer |
|---|---|
| DPF Full See Owner's Manual
(and image display) |
- |
| DPF Manual Regeneration Available
(and image display) |
- |
| DPF Full Manual Regeneration Required See Owner's Manual
(and image display) |
- |
| Manual Regeneration in Process Keep Flammables Away from Vehicle
(and image display) |
- |
| Manual Regeneration Unavailable DPF Normal
(and image display) |
- |
| DPF Regeneration in Process
(and image display) |
- |
| DPF Full Visit Your Dealer
(and image display) |
- |
The combination meter assembly displays the following messages based on signals received from the urea pump control ECU via the ECM.
| Message | Buzzer |
|---|---|
| AdBlue Level Low Fill up AdBlue in ***km See Owner's Manual
AdBlue Level Low Fill up AdBlue in ***mile See Owner's Manual |
- |
| AdBlue Level Low Fill up AdBlue in ***km See Owner's Manual
AdBlue Level Low Fill up AdBlue in ***mile See Owner's Manual |
Sounds |
| AdBlue Level Low No Start in ***km Fill up AdBlue See Owner's Manual
AdBlue Level Low No Start in ***miles Fill up AdBlue See Owner's Manual |
Sounds |
| AdBlue Empty Unable to Restart Engine Fill up AdBlue See Owner's Manual | Sounds |
| Emissions too High Check AdBlue Visit Your Dealer | Sounds |
| Emissions too High No Start in ***km Check AdBlue Visit Your Dealer
Emissions too High No Start in ***miles Check AdBlue Visit Your Dealer |
Sounds |
| Emissions too High Unable to Restart Engine Check AdBlue Visit Your Dealer | Sounds |
| Fill up AdBlue in ***km See Owner's Manual
Fill up AdBlue in ***miles See Owner's Manual |
- |
The combination meter assembly displays the following messages based on signals received from the ECM.
| Message | Buzzer |
|---|---|
| Cruise Control Malfunction Visit Your Dealer | Sounds |
The combination meter assembly displays the following messages based on signals received from the ECM.
| Message | Buzzer |
|---|---|
| Speed Limiter Malfunction Visit Your Dealer | Sounds |
The combination meter assembly displays the following messages based on signals received from the forward recognition camera.
| Message | Buzzer |
|---|---|
| Lane departure alert
(image display) |
Sounds |
| LDA Malfunction Visit Your Dealer | Sounds |
| LDA Unavailable | Sounds |
| Lane Departure Alert Turned On Yaw Assist Active* | - |
| Lane Departure Alert Turned On Yaw Assist Inactive* | - |
| LDA Unavailable at Current Speed | - |
| Lane departure alert system status
(image display) |
- |
| Would You Like to Take a Break?
(and image display) |
Sounds |
The combination meter assembly displays the following messages based on signals received from the forward recognition camera.
| Message | Buzzer |
|---|---|
| RSA Malfunction Visit Your Dealer | Sounds |
The combination meter assembly displays the following messages based on signals received from the engine stop and start ECU.
| Message | Buzzer |
|---|---|
|
*: Models with manual transmission |
|
| Stop & Start System Active Shift to N and Press Clutch to Restart* | Sounds |
| Stop & Start System Malfunction Visit Your Dealer | Sounds |
The combination meter assembly displays the following messages based on signals received from the ECM.
| Message | Buzzer |
|---|---|
| High Transmission Fluid Temp See Owner's Manual | Sounds |
The combination meter assembly displays the following messages based on signals received from the ECM.
| Message | Buzzer |
|---|---|
| Press the Accelerator Pedal when Starting Off | - |
The combination meter assembly displays the following messages based on signals received from the tire pressure warning ECU and receiver via the main body ECU.
| Message | Buzzer |
|---|---|
| TPWS Malfunction Visit Your Dealer | - |
| Setting Tire Pressure Warning System | - |
| Tire Pressure Recalibrating Please Wait until Complete | - |
| Tire Pressure Low Check Tire
(and image display) |
- |
The combination meter assembly displays the following messages based on signals received from the skid control ECU.
| Message | Buzzer |
|---|---|
|
*1: Models with Toyota Safety Sense *2: Models with VSC |
|
| Braking Power Low Stop in a Safe Place See Owner's Manual | Sounds |
| Antilock Brake System Malfunction Visit Your Dealer | Sounds |
| Secondary Collision Brake system Malfunction Visit Your Dealer*1 | Sounds |
| Traction Control Turned OFF*2 | Sounds |
The combination meter assembly displays the following messages based on signals received from the main body ECU.
| Message | Buzzer |
|---|---|
| Release Parking Brake | Sounds |
The combination meter assembly displays the following messages based on signals received from the clearance warning ECU assembly.
| Message | Buzzer |
|---|---|
| Toyota parking assist-sensor system detection display
(image display) |
- |
| Toyota parking assist-sensor system temporary mute display | - |
| Parking Assist Malfunction Visit Your Dealer | Sounds |
| Parking Assist Unavailable Clean Parking Assist Sensor | Sounds |
| Parking Assist Unavailable | Sounds |
The combination meter assembly displays the following messages based on signals received from the blind spot monitor sensor LH.
| Message | Buzzer |
|---|---|
| Rear Cross Traffic Alert Malfunction Visit Your Dealer | Sounds |
| Rear Cross Traffic Alert Unavailable | Sounds |
| Blind Spot Monitor Unavailable | Sounds |
| Blind Spot Monitor Malfunction Visit Your Dealer | Sounds |
The combination meter assembly displays the following messages based on signals received from the airbag ECU assembly.
| Message | Buzzer |
|---|---|
| SRS Airbag System Malfunction Visit Your Dealer | Sounds |
The combination meter assembly displays the following messages based on signals received from the forward recognition camera.
| Message | Buzzer |
|---|---|
| ADJUSTING FORWARD CAMERA | - |
| ERROR ADJUSTING FRONT RADAR BEAM | - |
| ADJUSTING FRONT RADAR BEAM VERTICAL | - |
| ADJUSTING FRONT RADAR BEAM HORIZONTAL | - |
| CHECKING PCS BRAKE | - |
| BRAKE! | Sounds |
| Front Camera Unavailable | - |
| Front Camera Unavailable See Owner's Manual | - |
| Pre-Collision System Malfunction Visit Your Dealer | Sounds |
| VSC Turned OFF Pre-Collision Brake System Unavailable | - |
| Pre-Collision System Unavailable | - |
| Pre-Collision System Unavailable Clean Sensor | - |
| Pre-Collision System OFF | - |
The combination meter assembly displays the following messages based on signals received from the main body ECU.
| Message | Buzzer |
|---|---|
| Driver door open
(image display) |
- |
| Front passenger door open
(image display) |
|
| Rear slide door LH open*1
(image display) |
|
| Rear slide door RH open*1
(image display) |
|
| Hood open*2
(image display) |
|
| Back door open
(image display) |
|
| Driver door open while driving*3
(image display) |
Sounds |
| Front passenger door open while driving*3
(image display) |
|
| Rear slide door LH open while driving*1, *3
(image display) |
|
| Rear slide door RH open while driving*1, *3
(image display) |
|
| Hood open while driving*2, *3
(image display) |
|
| Back door open while driving*3
(image display) |
*1: The rear door on the driver side is only displayed for 5-door models.
*2: Models with theft deterrent system
*3: If the vehicle has reached a speed of 5 km/h (3 mph).
The combination meter assembly displays the following messages based on signals received from the main body ECU.
| Message | Buzzer |
|---|---|
|
*: Models with automatic high beam |
|
| Turn Lights OFF | Sounds |
| Headlight System Malfunction Visit Your Dealer* | Sounds |
| To Activate Automatic High Beam, Switch Headlights to High Beam* | - |
The combination meter assembly displays the following messages based on signals.
| Message | Buzzer |
|---|---|
|
*1: Models with automatic transmission *2: Models for G.C.C. countries |
|
| Engine Stopped Shift into P Position*1 | Sounds |
| Engine Stopped Stop in a Safe Place | Sounds |
| Not Ready to Drive | - |
| Engine Stopped Press Brake Firmly to Restart | - |
| Speed Limit Exceeded*2 | Sounds |
| Roads may be Icy Drive with Care
(and image display) |
Sounds |
Buzzer
The table below shows the warning and reminder functions of the buzzer in the combination meter assembly.
|
*1: Models with manual transmission *2: Models for G.C.C countries *3: Models with Toyota Safety Sense *4: Models with lane departure alert system *5: Models with front center seat belt reminder system *6: Models with rear seat belt warning function *7: Except models for G.C.C countries *9: Models with road sign assist system *10: Models with automatic transmission *11: Models with stop and start system *12: Models with TFT LCD monitor type multi-information display *13: Models with segment LCD monitor type multi-information display *14: Models with speed limiter system *15: Models with 1GD-FTV engine *16: Models with Diesel Particulate Filter (DPF) system |
|
| Priority | Item |
| 1 | Reverse for 6-speed Manual Transmission Warning Buzzer (Once)*1 |
| 2 | Driver Seat Belt Warning Buzzer (Maximum 5 Times)*2 |
| 3 | Emergency Back Door Warning Buzzer (Continuous) |
| 4 | Pre-Collision System (PCS) Warning Buzzer (Intermittent)*3 |
| 5 | Key Reminder Buzzer (Intermittent) |
| 6 | Pedestrian Warning/Vehicle Distance Time Alert Buzzer (Intermittent)*3 |
| 7 | Lane Departure Alert System Cancel Warning Buzzer (Twice)*4 |
| 8 | Lane Departure Alert System Warning Buzzer (Intermittent)*4 |
| 9 | Unexpected Vehicle Motion Warning Buzzer (Continuous) |
| 10 | Unexpected Vehicle Motion Warning Buzzer (Intermittent) |
| 11 | Brake Fluid Low Warning Buzzer (Intermittent) |
| 12 | Engine Oil Pressure Warning Buzzer (Intermittent) |
| 13 | Driver Seat Belt Warning Buzzer (Once)*2 |
| 14 | Front Center Seat Belt Warning Buzzer (Once)*2, *5 |
| 15 | Front Passenger Seat Belt Warning Buzzer (Once)*2 |
| 16 | Rear Passenger Seat Belt Warning Buzzer (Once)*2, *6 |
| 17 | Seat Belt Warning Level 2 Buzzer (Intermittent) |
| 18 | Seat Belt Warning Level 1 Buzzer (Intermittent)*2 |
| 19 | Rear Seat Belt Warning Level 1 Buzzer (Intermittent)*6, *7 |
| 20 | Seat Belt Warning Level 1 Buzzer (Intermittent)*7 |
| 21 | Road Sign Assist System Warning Buzzer (Once)*9 |
| 22 | Engine Coolant Temperature Warning Buzzer (Once) |
| 23 | Door Open when Shift Position not in P Warning Buzzer (Continuous)*10 |
| 24 | Stop and Start System Warning Buzzer (Continuous)*11 |
| 25 | Brake System Temperature Rise Warning/Active Test Buzzer (Intermittent) |
| 26 | Multi-information Display Warning Buzzer (Once)*12 |
| 27 | Engine Malfunction Information Buzzer (Once)*13 |
| 28 | Speed Limit Warning Buzzer (Intermittent)*2 |
| 29 | Speed Limiter Buzzer (Intermittent)*14 |
| 30 | Parking Brake Engaged Warning Buzzer (Intermittent) |
| 31 | Door Open while Driving Warning Buzzer (Intermittent) |
| 32 | Vehicle Sway Warning Buzzer (Twice)*4 |
| 33 | Shift Reject Buzzer (Twice)*10 |
| 34 | Fuel Sedimenter Warning Buzzer (Continuous)*15 |
| 35 | Diesel Particulate Filter (DPF) Buzzer (Intermittent)*16 |
| 36 | Light Reminder Buzzer (Continuous) |
| 37 | Pre-collision Brake Assist Notification Buzzer (Intermittent)*3 |
| 38 | PCS Warning Notification Buzzer (Intermittent)*3 |
| 39 | Brake Inspections Standby Mode Notification Buzzer (Intermittent)*3 |
| 40 | Radar Axis Adjustment Complete Notification Buzzer (Intermittent)*3 |
| 41 | Camera Axis Adjustment Complete Notification Buzzer (Intermittent)*3 |
| 42 | Pre-collision Braking Notification Buzzer (Continuous)*3
Return from Brake Inspection Mode Notification Buzzer (Continuous)*3 Radar Axis Adjustment Incomplete Notification Buzzer (Continuous)*3 Camera Axis Adjustment Start Notification Buzzer (Continuous)*3 |
| 43 | Turn Signal/Hazard Warning Operation Buzzer (Intermittent) |
Eco Driving Indicator and ECO Driving Indicator Zone Display (Models with Automatic Transmission)
The operating diagram of Eco driving indicator is as follows:
When the ECM, using information (such as vehicle speed, accelerator pedal depressed volume, engine speed signal (engine r/min data), and so on), calculates that the vehicle is driven in an Eco-friendly manner, it turns on Eco driving indicator and shows the bar graph of ECO driving indicator zone display within zone of Eco driving.
The following table shows the operation of Eco driving indicator and ECO driving indicator zone display in different driving conditions:
| Driving Condition | Eco Driving Indicator | ECO Driving Indicator Zone Display |
|---|---|---|
| While Stopped | Turns off |
|
| While Eco Driving | Turns on |
|
| While Non-eco Driving | Turns off |
|
| When any of the following conditions is met, operation is stopped.
·
Ignition switch off ·
Engine stopped ·
Shift position is not D. ·
The vehicle is being driven at a speed of approximately 130 km/h (81 mph) or higher. |
Turns off |
|
| Driving Condition | Eco Driving Indicator | ECO Driving Indicator Zone Display |
|---|---|---|
| While Stopped | Turns off |
|
| While Eco Driving | Turns on |
|
| While Non-eco Driving | Turns off |
|
| When any of the following conditions is met, operation is stopped.
·
Ignition switch off ·
Engine stopped ·
Shift position is not D. ·
The vehicle is being driven at a speed of approximately 130 km/h (81 mph) or higher. |
Turns off |
|