FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
| Tire Pressure Warning ECU and Receiver | ·
Receives the data from the tire pressure warning valve and transmitter and monitors the tire inflation pressure. ·
Outputs the respective signal to the combination meter assembly when a drop in the tire inflation pressure, a system malfunction or the beginning of initialization is detected. |
|
| Tire Pressure Warning Valve and Transmitter | Detects the pressure, internal temperature and rotational acceleration of the tire, and transmits the measured values and the ID code to the tire pressure warning ECU and receiver. | |
| Tire Pressure Warning Reset Switch | ·
Initializes the system by performing a switch operation. ·
Selects the wheel set. |
|
| Combination Meter Assembly | Tire Pressure Warning Light | ·
Illuminates or stays on after blinking for 1 minute to warn the driver in accordance with the signal from the tire pressure warning system. ·
Flashes 3 times after initialization. |
| Central Gateway ECU (Network Gateway ECU) | Relays and transmits each CAN communication data signal. | |
| Main Body ECU (Multiplex Network Body ECU) | ·
Receives the signal from the tire pressure warning ECU and receiver and outputs it to the combination meter assembly via CAN communication. ·
Sends a vehicle speed signal to the tire pressure warning ECU and receiver. |
|
FUNCTION
Warning Function
When any of the following conditions are met, the tire pressure warning system illuminates the tire pressure warning light to warn the driver.
·
When the tire pressure decreases to approximately 80% or less of the default tire pressure set during system initialization. ·
When the tire pressure decreases rapidly and drops below approximately 80% or less of the tire pressure when warm. |
When driving for a certain period of time after the system has been initialized, the system corrects the tire pressure set during initialization according to the vehicle driving conditions and sets the tire pressure when warm.
The tire pressure warning pressure (pressure at which the tire pressure warning light is illuminated) cannot be set to approximately 80% or less of a specified tire pressure value.
The value that is approximately 80% of the set tire pressure during initialization*1 and the lower limit threshold value*2 are both displayed on the Global TechStream (GTS), and the higher of the 2 values is set as the tire pressure warning threshold value.
*1: Global TechStream (GTS) data list item "Initial Threshold of Low-pressure"
*2: Global TechStream (GTS) data list item "Threshold of Low-pressure (Lower Limit)"
If the tire pressure is decreased in order to adjust the tire pressure, even if the adjusted tire pressure is 80% or more than the tire pressure set during system initialization, the tire pressure warning light may illuminate if the tire pressure drops below 80% of the tire pressure set when the tires are warmed. In this case, perform initialization again.
Initial Check Function
After the ignition switch on, the tire pressure warning ECU and receiver illuminates the tire pressure warning light for 3 seconds to check the warning light circuits.
Initialization Function
By operating the tire pressure warning reset switch, the tire pressure warning ECU and receiver can be set to issue a warning at an inflation pressure that corresponds to the type of tires fitted to the vehicle. Therefore, the warning threshold must be set to the proper value in order to comply with local regulations.
Operate the tire pressure warning reset switch only after the inflation pressures of all tires (except the compact spare tire) have been adjusted on the vehicle.
During initialization, the tire pressure warning valve and transmitters measure the inflation pressure of the tires, and register the signals that are transmitted into the tire pressure warning ECU and receiver at a frequency of approximately once per minute. The initialization process is completed when signals from all tires (except the compact spare tire) have been received.
Perform initialization in the following cases:
|
*: Perform initialization after the transmitter ID registration is completed. |
·
Before delivery of a new vehicle. ·
After replacement of the tire pressure warning ECU and receiver.* ·
After replacement of a tire pressure warning valve and transmitter.* ·
When the tire pressure is adjusted. ·
When the specified tire pressure changes due to the use of a different size or type of tire. ·
When the specified tire pressure changes due to a change in the vehicle load, the speed range that the vehicle will be used in, etc. ·
When a tire rotation is performed and the specified tire pressures are different for the front and rear of the vehicle. |
After the initialization operation has completed, the tire pressure warning ECU and receiver receives an initialization signal and the tire pressure warning light flashes 3 times.
Before performing initialization, adjust the tire inflation pressure to the recommended pressure when the tires are cold. For details, refer to the Repair Manual.
DIAGNOSIS
To inform the driver when the tire pressure warning ECU and receiver detects a malfunction in the system, the tire pressure warning ECU and receiver blinks the tire pressure warning light for 1 minute, after which the light stays on. The tire pressure warning ECU and receiver also stores Diagnostic Trouble Codes (DTCs) in memory.
5-digit DTCs can be read by connecting the Global TechStream (GTS) to the DLC3. For details, refer to the Repair Manual.