SYSTEM CONTROL
The power window control system has the following functions:
| Function | Outline |
|---|---|
|
*1: Although this function is disabled by default, the function can be set via the customization function. *2: Models without wireless door lock control system *3: Models with wireless door lock control system |
|
| Power Up-and-down | This function causes the window to open or close while the multiplex network master switch assembly or power window regulator switch assembly is being pulled halfway up or pushed halfway down. The window stops as soon as the switch is released. |
| One-touch Auto Up-and-down | The one-touch auto up-and-down function enables the window to be fully opened or closed at a touch of the multiplex network master switch assembly or power window regulator switch assembly. |
| Jam Protection | The jam protection function automatically stops the power window and moves it downward if a foreign object gets jammed in the window during power up operation or one-touch auto up operation. |
| Catch Protection | Catch protection function automatically stops the power window if a foreign object gets caught in the window during power down operation or one-touch auto down operation. |
| Soft Stop | During an up or down operation of the power window, the power window ECU stops the current to the power window motor just before the door glass is fully closed or opened. |
| Remote Control | The multiplex network master switch assembly can control the up-and-down operation of the front passenger door window. |
| Window Lock | ·
When the window lock switch is on, disable the operation of the front passenger door window using the power window regulator switch assembly. ·
Even when the window lock switch is on, the front passenger door window can be operated using the multiplex network master switch assembly. |
| Key Off Operation | ·
Makes it possible to operate the power windows for approximately 43 seconds after the ignition switch is turned off, if either front door is not opened. ·
If the window lock switch is off, the windows can be operated using the multiplex network master switch assembly or the power window regulator switch assembly. If the window lock switch is on, only the multiplex network master switch assembly can be used to operate the windows. |
| Key-linked Up-and-down*1 | When the door is locked, and the driver door key cylinder (or passenger door key cylinder)*2 is turned and maintained in the lock direction for 1.5 seconds or more, the main body ECU activates the power window motors to raise all door windows while the key cylinder is turned. Similarly, when the door is unlocked, turning and maintaining the driver door key cylinder (or passenger door key cylinder)*2 in the unlock direction for 1.5 seconds or more will cause all door windows to be lowered. |
| Transmitter-linked Up-and-down*1, *3 | When the lock button is pressed and held for longer than 3 seconds, the main body ECU activates the power window motors in accordance with the signal to raise the all door windows. Similarly, when the unlock button is pressed and held for longer than 3 seconds, the main body ECU activates the power window motors in accordance with the signal to lower the all door windows. |
| Customization | The on or off setting of some functions can be performed using the Global TechStream (GTS). For details, refer to the Repair Manual. |
The ECU built into each power window motor stores the initial position of its door window glass. The initial position is not cleared even if the terminals, fuses or the power window motor connector are disconnected. However, after removing or reinstalling window components, or replacing the power window regulator switch assembly or power window regulator motor assembly, the stored initial position data must be cleared and/or initialization must be performed. For details, refer to the Repair Manual.
Jam Protection Function
A jam protection function automatically stops the power window and moves it downward if a foreign object gets jammed in the door window glass during power up operation and one-touch auto up operation.
After the jam protection function has operated when a power up operation or one-touch auto up operation was performed, the jam protection function will not operate if the power up operation is performed again within approximately 4 seconds.
The operation of the jam protection function is described below:
| Operation | Function |
|---|---|
| During each door one-touch auto up operation and remote control power up/one-touch auto up operation | Down operation of approximately 135 mm (5.3 in.) or 5.0 seconds |
| During each door power up operation | Down operation of approximately 25 mm (1.0 in.) or 5.0 seconds |
The power window ECU determines if a foreign object gets jammed according to changes in the output signal from the pulse sensor (Hall IC). Both of the following 2 judgment methods are used:
Catch Protection Function
A catch protection function automatically stops the power window if a foreign object gets caught in the door window during power down operation and one-touch auto down operation.
After the catch protection function has operated when a power down operation or one-touch auto down operation was performed, the catch protection function will not operate if the power down operation is performed again within approximately 4 seconds.
The power window ECU determines if a foreign object gets caught according to changes in the output signal from the pulse sensor (Hall IC). The judgment method is as follows:
Soft Stop Function
During an up or down operation of the power window, the soft stop function stops the current to the power window motor just before the door glass is fully closed or opened. This reduces the load on the door glass outer weatherstrip.
Just before the door glass is fully closed or opened, the power window ECU determines if the door glass stop position is detected according to changes in the output signal from the pulse sensor (Hall IC). The judgment method is as follows:
FAIL-SAFE
If a Hall IC in the power window motor malfunctions, some power window functions will be prohibited in fail-safe mode:
Each power window only operates when the corresponding power window regulator switch is fully pushed down or pulled up and held in that position.
When any power window ECU detects an abnormality in a Hall IC, which detects the position, speed and direction of the window, it switches to fail-safe mode:
DIAGNOSIS
If a power window ECU detects a malfunction in the power window control system, a Diagnostic Trouble Code (DTC) is stored in memory.
The DTCs can be read using the Global TechStream (GTS). For details, refer to the Repair Manual.