CONSTRUCTION
Models without VSC
The brake actuator assembly consists of the brake actuator portion and skid control ECU.
| *1 | Skid Control ECU | - | - |
| *a | Brake Actuator Portion | - | - |
The actuator portion consists of 4 pressure holding solenoid valves, 4 pressure reduction solenoid valves, 2 pumps and 2 reservoirs.
| *1 | Brake Master Cylinder Sub-assembly | *2 | Brake Actuator Assembly |
| *3 | Pressure Holding Solenoid Valve | *4 | Pressure Reduction Solenoid Valve |
| *5 | Pump | *6 | Reservoir |
| *7 | Front Brake (Right Side) | *8 | Rear Brake (Left Side) |
| *9 | Rear Brake (Right Side) | *10 | Front Brake (Left Side) |
Models with VSC
The brake actuator assembly consists of the brake actuator portion and skid control ECU.
| *1 | Skid Control ECU | - | - |
| *a | Brake Actuator Portion | - | - |
The brake actuator portion consists of 2 master cylinder cut solenoid valves, 2 reservoir cut solenoid valve, 4 pressure holding solenoid valves, 4 pressure reduction solenoid valves, 2 pumps, 2 reservoirs and a master cylinder pressure sensor.
| *1 | Brake Master Cylinder Sub-assembly | *2 | Brake Actuator Assembly |
| *3 | Master Cylinder Pressure Sensor | *4 | Master Cylinder Cut Solenoid Valve |
| *5 | Reservoir Cut Solenoid Valve | *6 | Pressure Holding Solenoid Valve |
| *7 | Pressure Reduction Solenoid Valve | *8 | Pump |
| *9 | Reservoir | *10 | Front Brake (Right Side) |
| *11 | Rear Brake (Left Side) | *12 | Rear Brake (Right Side) |
| *13 | Front Brake (Left Side) | - | - |
OPERATION
ABS and EBD
Based on the signals received from the 4 speed sensors, the skid control ECU calculates the speed of each wheel, and checks the wheel slipping conditions. In accordance with the slipping condition, the skid control ECU controls each solenoid valve in the brake actuator assembly in order to adjust the fluid pressure of each wheel cylinder in the following 3 modes: pressure increase, pressure holding and pressure reduction modes.
| *1 | Port A | *2 | Port B |
| *3 | Pressure Holding Solenoid Valve | *4 | Pressure Reduction Solenoid Valve |
| *a | Increase Mode | *b | Holding Mode |
| *c | Reduction Mode | *d | to Wheel Cylinder |
| *e | to Reservoir and Pump | *f | from Wheel Cylinder |
| Not Activated | Normal Braking | - | - |
|---|---|---|---|
| Activated | Increase Mode | Holding Mode | Reduction Mode |
| Pressure Holding Solenoid Valve (Port A) | Off (Open) | On (Close) | On (Close) |
| Pressure Reduction Solenoid Valve (Port B) | Off (Close) | Off (Close) | On (Open) |
| Wheel Cylinder Pressure | Increases | Holds | Reduces |
Brake Assist
In the event of emergency braking, the skid control ECU determines the driver's intention based on the speed of the pressure increase in the master cylinder determined by the master cylinder pressure sensor signal. If the skid control ECU judges the need for additional brake assist, pressure is generated by the pump in the brake actuator assembly and directed to the wheel cylinder to apply a large amount of fluid pressure.
| *1 | Brake Master Cylinder Sub-assembly | *2 | Brake Actuator Assembly |
| *3 | Master Cylinder Pressure Sensor | *4 | Pump |
| *5 | Reservoir | *6 | Rear Brake (Right Side) |
| *7 | Rear Brake (Left Side) | *8 | Rear Brake (Right Side) |
| *9 | Front Brake (Left Side) | - | - |
| Item | Port | Brake Assist Not Activated | Brake Assist Activated | ||
|---|---|---|---|---|---|
|
*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions. |
|||||
| Master Cylinder Cut Solenoid Valve | (1), (4) | (A), (D) | Off (Open) | On* | |
| Reservoir Cut Solenoid Valve | (2), (3) | (B), (C) | Off (Closed) | On (Open) | |
| Front Brakes | Pressure Holding Solenoid Valve | (5), (8) | (E), (H) | Off (Open) | Off (Open) |
| Pressure Reduction Solenoid Valve | (9), (12) | (I), (L) | Off (Closed) | Off (Closed) | |
| Rear Brakes | Pressure Holding Solenoid Valve | (6), (7) | (F), (G) | Off (Open) | Off (Open) |
| Pressure Reduction Solenoid Valve | (10), (11) | (J), (K) | Off (Closed) | Off (Closed) | |
| Pump | Off | On | |||
TRC
The fluid pressure generated by the pump is regulated by the master cylinder cut solenoid valve to the required pressure. Thus, the wheel cylinders of the drive wheels are controlled in the following 2 modes: pressure increase and pressure reduction modes to control the slippage of the drive wheels. Each pressure holding solenoid valve and the pressure reduction solenoid valve is turned on or off in accordance with the ABS and EBD operation patterns.
| *1 | Brake Master Cylinder Sub-assembly | *2 | Brake Actuator Assembly |
| *3 | Master Cylinder Pressure Sensor | *4 | Pump |
| *5 | Reservoir | *6 | Front Brake (Right Side) |
| *7 | Rear Brake (Left Side) | *8 | Rear Brake (Right Side) |
| *9 | Front Brake (Left Side) | - | - |
| Item | Port | TRC Not Activated | TRC Activated | |||
|---|---|---|---|---|---|---|
| Increase Mode | Reduction Mode | |||||
|
*: The solenoid valve switches the hydraulic pressure between "open" and "closed" in accordance with the operating conditions by adjusting continually. |
||||||
| Master Cylinder Cut Solenoid Valve | (1), (4) | (A), (D) | Off (Open) | On* | On* | |
| Reservoir Cut Solenoid Valve | (2), (3) | (B), (C) | Off (Closed) | On (Open) | On (Open) | |
| Front Brakes | Pressure Holding Solenoid Valve | (5), (8) | (E), (H) | Off (Open) | On (Closed) | On (Closed) |
| Pressure Reduction Solenoid Valve | (9), (12) | (I), (L) | Off (Closed) | Off (Closed) | Off (Closed) | |
| Brake Wheel Cylinder Pressure | - | - | - | - | - | |
| Rear Brakes | Pressure Holding Solenoid Valve | (6), (7) | (F), (G) | Off (Open) | Off (Open) | Off (Open) |
| Pressure Reduction Solenoid Valve | (10), (11) | (J), (K) | Off (Closed) | Off (Closed) | Off (Closed) | |
| Brake Wheel Cylinder Pressure | - | - | - | Increases | Reduces | |
| Pump | Off | On | Off | |||
VSC
The VSC, by the way of solenoid valves, controls fluid pressure generated by the pump and applies it to the brake wheel cylinder of each wheel in the following 3 modes: pressure increase, pressure holding and pressure reduction modes. As a result, the tendency of front wheel skid or rear wheel skid is controlled.
In understeer restraining control, the brake of the front and rear wheels on the inner circle of the turn are applied. Also, depending on whether the brake is on or off and also depending on the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if the wheel is targeted for braking. The following diagram shows the hydraulic circuit in pressure increase mode as it controls a front wheel skid condition while the vehicle is making a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned on or off in accordance with the ABS and EBD operation patterns.
| *1 | Brake Master Cylinder Sub-assembly | *2 | Brake Actuator Assembly |
| *3 | Master Cylinder Pressure Sensor | *4 | Pump |
| *5 | Reservoir | *6 | Front Brake (Right Side) |
| *7 | Rear Brake (Left Side) | *8 | Rear Brake (Right Side) |
| *9 | Front Brake (Left Side) | - | - |
| Item | Port | VSC Not Activated | VSC Activated | ||||
|---|---|---|---|---|---|---|---|
| Increase Mode | Holding Mode | Reduction Mode | |||||
|
*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions. |
|||||||
| Master Cylinder Cut Solenoid Valve | (1), (4) | (A), (D) | Off (Open) | On* | On* | On* | |
| Reservoir Cut Solenoid Valve | (2), (3) | (B), (C) | Off (Closed) | On (Open) | On (Open) | On (Open) | |
| Front Brake | Pressure Holding Solenoid Valve | (5) | (E) | Off (Open) | Off (Open) | On (Closed) | On (Closed) |
| (8) | (H) | Off (Open) | On (Closed) | On (Closed) | On (Closed) | ||
| Pressure Reduction Solenoid Valve | (9) | (I) | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | |
| (12) | (L) | Off (Closed) | Off (Closed) | Off (Closed) | Off (Closed) | ||
| Brake Wheel Cylinder Pressure | Right | - | - | Increases | Holds | Reduces | |
| Left | - | - | - | - | - | ||
| Rear Brake | Pressure Holding Solenoid Valve | (6) | (F) | Off (Open) | On (Closed) | On (Closed) | On (Closed) |
| (7) | (G) | Off (Open) | Off (Open) | On (Closed) | On (Closed) | ||
| Pressure Reduction Solenoid Valve | (10) | (J) | Off (Closed) | Off (Closed) | Off (Closed) | Off (Closed) | |
| (11) | (K) | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| Brake Wheel Cylinder Pressure | Right | - | - | Increases | Holds | Reduces | |
| Left | - | - | - | - | - | ||
| Pump | Off | On | On | On | |||
In oversteer restraining control, the brakes of the front and rear wheels on the outer circle of the turn are applied. Also, depending on whether the brake is on or off and also depending on the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if the wheel is targeted for braking. The following diagram shows the hydraulic circuit in pressure increase mode, as it controls the rear wheel skid condition while the vehicle is making a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned on or off in accordance with the ABS and EBD operation patterns.
| *1 | Brake Master Cylinder Sub-assembly | *2 | Brake Actuator Assembly |
| *3 | Master Cylinder Pressure Sensor | *4 | Pump |
| *5 | Reservoir | *6 | Front Brake (Right Side) |
| *7 | Rear Brake (Left Side) | *8 | Rear Brake (Right Side) |
| *9 | Front Brake (Left Side) | - | - |
| Item | Port | VSC Not Activated | VSC Activated | ||||
|---|---|---|---|---|---|---|---|
| Increase Mode | Holding Mode | Reduction Mode | |||||
|
*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions. |
|||||||
| Master Cylinder Cut Solenoid Valve | (1), (4) | (A), (D) | Off (Open) | On* | On* | On* | |
| Reservoir Cut Solenoid Valve | (2), (3) | (B), (C) | Off (Closed) | On (Open) | On (Open) | On (Open) | |
| Front Brake | Pressure Holding Solenoid Valve | (5) | (E) | Off (Open) | On (Closed) | On (Closed) | On (Closed) |
| (8) | (H) | Off (Open) | Off (Open) | On (Closed) | On (Closed) | ||
| Pressure Reduction Solenoid Valve | (9) | (I) | Off (Closed) | Off (Closed) | Off (Closed) | Off (Closed) | |
| (12) | (L) | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | ||
| Brake Wheel Cylinder Pressure | Right | - | - | - | - | - | |
| Left | - | - | Increases | Holds | Reduces | ||
| Rear Brake | Pressure Holding Solenoid Valve | (6) | (F) | Off (Open) | Off (Open) | On (Closed) | On (Closed) |
| (7) | (G) | Off (Open) | On (Closed) | On (Closed) | On (Closed) | ||
| Pressure Reduction Solenoid Valve | (10) | (J) | Off (Closed) | Off (Closed) | Off (Closed) | On (Open) | |
| (11) | (K) | Off (Closed) | Off (Closed) | Off (Closed) | Off (Closed) | ||
| Brake Wheel Cylinder Pressure | Right | - | - | - | - | - | |
| Left | - | - | Increases | Holds | Reduces | ||
| Pump | Off | On | On | On | |||
Trailer Sway Control
The operation of the solenoid valves under the trailer sway control is the same as the VSC operation.
AUTO LSD
AUTO LSD is a function that has effects similar to a mechanical type LSD. AUTO LSD employs the TRC to control brake hydraulic pressure and engine output.
The skid control ECU detects slippage that occurs as a result of a rotational difference between the drive wheel and the non-driven wheel. Via the TRC, the AUTO LSD detects the wheel slip that occurs (the wheel that is rotating faster) , based on the rotational difference of the right and left drive wheels, and puts AUTO LSD into action.
| *1 | Brake Master Cylinder Sub-assembly | *2 | Brake Actuator Assembly |
| *3 | Master Cylinder Pressure Sensor | *4 | Pump |
| *5 | Reservoir | *6 | Front Brake (Right Side) |
| *7 | Rear Brake (Left Side) | *8 | Rear Brake (Right Side) |
| *9 | Front Brake (Left Side) | - | - |
| Item | Port | AUTO LSD Operation Not Activated | AUTO LSD Operation | |||
|---|---|---|---|---|---|---|
| Increase Mode | Reduction Mode | |||||
|
*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions. |
||||||
| Master Cylinder Cut Solenoid Valve | (1) | (A) | Off (Open) | Off (Open) | Off (Open) | |
| (4) | (D) | Off (Open) | On* | On* | ||
| Reservoir Cut Solenoid Valve | (2) | (B) | Off (Closed) | Off (Closed) | Off (Closed) | |
| (3) | (C) | Off (Closed) | On (Open) | On (Open) | ||
| Front Brakes | Pressure Holding Solenoid Valve | (5) | (E) | Off (Open) | Off (Open) | Off (Open) |
| (8) | (H) | Off (Open) | On (Closed) | On (Closed) | ||
| Pressure Reduction Solenoid Valve | (9) | (I) | Off (Closed) | Off (Closed) | Off (Closed) | |
| (12) | (L) | Off (Closed) | Off (Closed) | Off (Closed) | ||
| Brake Wheel Cylinder Pressure | Right | - | - | - | - | |
| Left | - | - | - | - | ||
| Rear Brakes | Pressure Holding Solenoid Valve | (6) | (F) | Off (Open) | Off (Open) | Off (Open) |
| (7) | (G) | Off (Open) | Off (Open) | Off (Open) | ||
| Pressure Reduction Solenoid Valve | (10) | (J) | Off (Closed) | Off (Closed) | Off (Closed) | |
| (11) | (K) | Off (Closed) | Off (Closed) | Off (Closed) | ||
| Brake Wheel Cylinder Pressure | Right | - | - | Increase | Reduces | |
| Left | - | - | - | - | ||
| Pump | Off | On | Off | |||
Hill-start Assist Control
Hill-start assist control is performed by closing the master cylinder cut solenoid valves after the driver operates the brake pedal and leaving a certain amount of hydraulic pressure created by the pump in the wheel cylinder. The diagram below shows the hydraulic circuit in the pressure holding mode.
| *1 | Brake Master Cylinder Sub-assembly | *2 | Brake Actuator Assembly |
| *3 | Master Cylinder Pressure Sensor | *4 | Pump |
| *5 | Reservoir | *6 | Front Brake (Right Side) |
| *7 | Rear Brake (Left Side) | *8 | Rear Brake (Right Side) |
| *9 | Front Brake (Left Side) | - | - |
| Item | Port | Hill-start Assist Control Not Activated | Hill-start Assist Control Activated | |||
|---|---|---|---|---|---|---|
| Holding Mode | Reduction Mode | |||||
|
*: Hydraulic pressure is controlled by continuously cycling the solenoid valves between open and closed, according to the operating conditions. |
||||||
| Master Cylinder Cut Solenoid Valve | (1), (4) | (A), (D) | Off (Open) | On* | On* | |
| Reservoir Cut Solenoid Valve | (2), (3) | (B), (C) | Off (Closed) | Off (Closed) | Off (Closed) | |
| Front Brakes | Pressure Holding Solenoid Valve | (5), (8) | (E), (H) | Off (Open) | Off (Open) | Off (Open) |
| Pressure Reduction Solenoid Valve | (9), (12) | (I), (L) | Off (Closed) | Off (Closed) | Off (Closed) | |
| Brake Wheel Cylinder Pressure | - | - | Holds | Reduces | ||
| Rear Brakes | Pressure Holding Solenoid Valve | (6), (7) | (F), (G) | Off (Open) | Off (Open) | Off (Open) |
| Pressure Reduction Solenoid Valve | (10), (11) | (J), (K) | Off (Closed) | Off (Closed) | Off (Closed) | |
| Brake Wheel Cylinder Pressure | - | - | Holds | Reduces | ||
| Pump | Off | Off | Off | |||