FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
| Speed Sensor | Detects the wheel speed of each of the 4 wheels. | |
| Stop Light Switch Assembly | Detects the brake pedal depressing signal. | |
| Hazard Warning Signal Switch Assembly | Switches the Hazard Warning Signal on and off. | |
| Brake Actuator Assembly | Solenoid Relay (Built into Skid Control ECU) | Supplies power to the solenoid valves. |
| Motor Relay (Built into Skid Control ECU) | Supplies power to the pump motor. | |
| Solenoid Valves | Change the fluid path based on the signals from the skid control ECU during the operation of the brake control system functions in order to control the fluid pressure applied to the wheel cylinders. | |
| Pump Motor | Drives the pumps inside the brake actuator. | |
| Skid Control ECU | Judges the vehicle driving condition based on the signals from each ECU, sensor and switch, and sends the brake control signals to the brake actuator. | |
| Central Gateway ECU (Network Gateway ECU) | Relays and transmits each CAN communication data signal. | |
| Combination Meter Assembly | Brake Warning Light | ·
Illuminates to alert the driver when the skid control ECU detects a malfunction in the EBD. ·
Illuminates to inform the driver when the brake fluid is low. |
| ABS Warning Light | Illuminates to alert the driver when the skid control ECU detects a malfunction in the ABS. | |
| Buzzer | Sounds to inform the driver when the system malfunctions. | |
| Component | Function | |
|---|---|---|
|
*1: Models with manual transmission *2: Models with automatic transmission *3: Models with gasoline engine *4: Models with pre-collision system *5: Models with towing package *6: Models with segment LCD monitor type multi-information display *7: Models with TFT LCD monitor type multi-information display |
||
| Speed Sensor | Detects the wheel speed of each of the 4 wheels. | |
| Steering Sensor | Detects the direction and angle of the steering wheel. | |
| Stop Light Switch Assembly | Detects the brake pedal depressing signal. | |
| VSC OFF Switch | Enables the driver to select Normal Mode, AUTO LSD Mode or VSC OFF Mode. | |
| Hazard Warning Signal Switch Assembly | Switches the Hazard Warning Signal on and off. | |
| Brake Actuator Assembly | Solenoid Relay (Built into Skid Control ECU) | Supplies power to the solenoid valves. |
| Motor Relay (Built into Skid Control ECU) | Supplies power to the pump motor. | |
| Motor Cut Relay (Built into Skid Control ECU) | Cuts the power to the pump motor when the motor relay malfunctions. | |
| Solenoid Valves | Change the fluid path based on the signals from the skid control ECU during the operation of the brake control system functions in order to control the fluid pressure applied to the wheel cylinders. | |
| Pump Motor | Drives the pumps inside the brake actuator. | |
| Master Cylinder Pressure Sensor | Detects the master cylinder pressure. | |
| Skid Control ECU | Judges the vehicle driving condition based on the signals from each ECU, sensor and switch, and sends the brake control signals to the brake actuator. | |
| ECM | ·
Controls the drive force when TRC and VSC are operating according to communication with the skid control ECU. ·
Sends the accelerator pedal position signal, reverse position signal*1, shift position signal*2, throttle position signal*3, engine speed signal and brake request signal to the skid control ECU. |
|
| Airbag ECU Assembly
·
Yawrate Sensor ·
Deceleration Sensor |
·
Sends the collision detection signal to the skid control ECU.*4 ·
The yawrate sensor detects the vehicle's yaw rate. ·
The acceleration sensor detects the vehicle's longitudinal and lateral deceleration. |
|
| Central Gateway ECU (Network Gateway ECU) | Relays and transmits each CAN communication data signal. | |
| Combination Meter Assembly | Brake Warning Light | ·
Illuminates to alert the driver when the skid control ECU detects a malfunction in the EBD. ·
Illuminates to inform the driver when the brake fluid is low. |
| ABS Warning Light | Illuminates to alert the driver when the skid control ECU detects a malfunction in the ABS. | |
| Slip Indicator Light | ·
Blinks to inform the driver when the TRC, AUTO LSD, VSC or trailer sway control*5 is operational. ·
Illuminates to alert the driver when the skid control ECU detects a malfunction in the TRC, AUTO LSD, VSC, trailer sway control*5 or hill-start assist control. |
|
| VSC OFF Indicator Light | Illuminates to inform the driver when AUTO LSD Mode or VSC OFF Mode is selected. | |
| AUTO LSD Indicator Light | Illuminates to inform the driver when the AUTO LSD Mode is entered using the VSC OFF switch. | |
| TRC OFF Indicator Light*6 | Illuminates to inform the driver when the VSC OFF Mode is entered using the VSC OFF switch. | |
| Multi-information Display*7 | ·
Displays the warning message when the skid control ECU detects a malfunction in the system. ·
Displays the information message when the VSC OFF Mode is entered using the VSC OFF switch. |
|
| Buzzer | Sounds to inform the driver when the system malfunctions or control restriction conditions. | |
OPERATING CONDITION
Hill-start Assist Control
Hill-start assist control operates when all of the following conditions have been met:
|
*1: Models with automatic transmission *2: Models with manual transmission |
·
The shift lever is in any position other than P, N or R (when forward climbing).*1 ·
The shift lever is in any position other than R (when forward climbing).*2 ·
The shift position is in R (when backward climbing). ·
The brake pedal is depressed and the vehicle is stopped. ·
The accelerator pedal is not depressed. ·
The parking brake is not applied. |
If any one of the following conditions is met during hill-start assist control operation, hill-start assist control will be canceled.
|
*1: Models with automatic transmission *2: Models with manual transmission |
·
The shift lever is moved to P, N or R (when forward climbing).*1 ·
The shift lever is moved to R (when forward climbing).*2 ·
The shift position is moved to a position other than R (when backward climbing). ·
The accelerator pedal is depressed. ·
The parking brake is applied. ·
2 seconds have elapsed since the driver release the brake pedal. |
Secondary Collision Brake
Secondary Collision Brake Operation Start Condition
When a collision detection signal is received from the airbag ECU while the vehicle speed is approximately 10 km/h or more, the secondary collision brake starts operating.
When a system malfunction is displayed on the multi-information display or the system is in test mode or maintenance mode, the secondary collision brake is prohibited from operating.
Secondary Collision Brake Operation Cancellation Condition
If one of the following conditions is detected, operation of the secondary collision brake is canceled.
·
The vehicle speed is below approximately 10 km/h. ·
Operation continues for a certain period of time. ·
After operating, the accelerator pedal is depressed a certain amount or more. |
Emergency Brake Signal
Operation Conditions of the emergency brake signal
Emergency brake signal operates when all of the following conditions have been met:
·
The vehicle speed is approximately 55 km/h or more. ·
The brake pedal is depressed and the vehicle is judged to be rapidly braking based on the deceleration rate. |
Cancellation conditions of the emergency brake signal
If any one of the following conditions is met during emergency brake signal operation, emergency brake signal will be canceled.
·
When the hazard warning lights are turned on by operating the hazard warning signal switch. ·
The brake pedal is released. ·
The parking brake is applied. ·
The deceleration rate of the vehicle is judged not to be high. The vehicle is judged not to be rapidly braking based on the deceleration rate. |
SYSTEM CONTROL
The brake control system has the following controls:
| Control | Outline |
|---|---|
|
*1: Models with VSC *2: Models with towing package *3: Models with pre-collision system |
|
| Anti-lock Brake System (ABS) | The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface. |
| Electronic Brake Force Distribution (EBD) | The EBD utilizes ABS, achieving proper brake force distribution between the front and rear wheels in accordance with the driving conditions. In addition, during braking while cornering, the EBD also controls the brake forces of the right and left wheels, helping maintain vehicle behavior. |
| Brake Assist*1 | The primary purpose of brake assist is to provide an auxiliary brake force to assist a driver who cannot generate a large brake force during emergency braking, helping ensure the vehicle's braking performance. |
| Traction Control (TRC)*1 | The TRC helps restrain the slippage of the drive wheels if the driver depresses the accelerator pedal excessively when starting off or while accelerating on a slippery surface. |
| Vehicle Stability Control (VSC)*1 | The VSC helps restrain sideways slippage of the vehicle during a strong front wheel skid or strong rear wheel skid, which may occur while cornering. |
| Trailer Sway Control*2 | If the tongue load is not properly adjusted while towing a trailer, trailer sway may be caused due to crosswinds, bumpy roads, steering operation, etc. Trailer sway control detects sway and regulates the brake of each wheel and the engine output in order to suppress trailer sway. |
| Auto Limited Slip Differential (AUTO LSD)*1 | Briefly pressing the VSC OFF switch in Normal Mode enters AUTO LSD Mode. The AUTO LSD achieves a function equivalent to that of an LSD system through the use of the TRC. The AUTO LSD applies brake hydraulic pressure to a slipping wheel to reduce the difference in rotation speed between the left and right drive wheels. This causes driving torque to be transmitted to the wheel opposite the slipping wheel. |
| Hill-start Assist Control*1 | When starting uphill, this control maintains the brake hydraulic pressure on all 4 wheels in order to momentarily prevent the vehicle from descending backward. |
| Emergency Brake Signal | In case of emergency braking, the emergency brake signal flashes the hazard warning lights to alert drivers in following vehicles. |
| Secondary Collision Brake*3 | After the airbags operate, this system automatically operates the brakes to suppress movement after a collision. |
FAIL-SAFE
If a failure occurs in the skid control ECU, sensors or brake actuator assembly, the system continues performing brake control by excluding the failed area and using only the areas that are operating normally.
DIAGNOSIS
If the skid control ECU detects a malfunction in the brake control system, the warning lights or indicator light illuminate. At the same time, a Diagnostic Trouble Code (DTC) is stored in the memory of the skid control ECU.
This system has a sensor signal check (test mode) function.
For details of DTCs and check function, refer to the Repair Manual.