Home › Engine / Hybrid System › 7GR-FKS (ENGINE CONTROL) › SFI SYSTEM
NM35X0E _51 Engine / Hybrid System _079945 7GR-FKS ENGINE CONTROL _0389299 SFI SYSTEM CO CONTROL F

7GR-FKS ENGINE CONTROL  SFI SYSTEM  CONTROL  DIRECT INJECTION 4-STROKE GASOLINE ENGINE SUPERIOR VERSION SEQUENTIAL MULTIPORT FUEL INJECTION (D-4S SFI)  


FUNCTION


a.

The D-4S SFI system directly detects the intake air volume with a hot-wire type mass air flow meter sub-assembly.


b.

The D-4S system is a fuel injection system which combines direct injection injectors and port injection injectors.


c.

Based on signals from each sensor, the ECM controls the injection volume and timing of each type of port fuel injector assembly and direct fuel injector assembly in accordance with engine load and engine speed in order to optimize combustion conditions.


d.

To promote warm-up of the catalyst after a cold engine start, this system uses a stratified air fuel mixture. This creates an area near the spark plug that is richer than the rest of the air fuel mixture. This also allows a greater amount of ignition timing retard to be used, raising the exhaust gas temperature. The increased exhaust gas temperatures promote rapid warm-up of the catalysts, significantly reducing exhaust emissions.

Fuel Injector System Activation Ranges
W123296E05
5.094,1.521 5.156,1.083 5.156,1.083 5.469,1.083 true 2.375,2.052 2.688,0.385 2.688,0.385 3.115,0.385 true 0.438,1.813 1.51,2.01 1.073,0.198 10 false Engine Load 5.552,1.01 6.5,1.344 0.948,0.333 10 true Direct Injection 2.125,2.458 4.083,2.708 1.958,0.25 10 true Direct Injection or Port Injection 3.146,0.323 5.073,0.708 1.927,0.385 10 true Direct Injection + Port Injection 3.24,2.938 4.25,3.167 1.01,0.229 10 true Engine Speed


e.

Stratified Combustion: To achieve stratified combustion, immediately after a cold engine start, fuel is injected into the intake port from the port fuel injector assembly during the exhaust stroke. Fuel is also injected from the direct fuel injector assembly near the end of the compression stroke. This results in an air fuel mixture that is stratified, and the area near the spark plug is richer than the rest of the air fuel mixture. This allows a retarded ignition timing to be used, raising the exhaust gas temperature. The increased exhaust gas temperatures promote rapid warm up of the catalysts, and significantly improve exhaust emission performance.


f.

Homogeneous Combustion: To optimize combustion conditions, the ECM controls injection volume and timing of the port fuel injector assemblies which inject fuel into the intake ports during the expansion, exhaust, and intake strokes. The ECM also controls the injection volume and timing of the direct fuel injector assemblies which inject fuel during the first half of the intake stroke. The homogeneous air fuel mixture is created by either combined or individual use of the 2 different types of injectors. This allows utilization of the evaporation heat of the injected fuel to cool the compressed air, and it also allows an increase of charging efficiency and power output.

W142391E01
0.271,0.156 2.563,0.49 2.292,0.333 10 false Mass Air Flow Meter Sub-assembly 0.969,0.656 1.99,0.969 1.021,0.313 10 false Air Flow Meter 0.448,1.156 2.438,1.521 1.99,0.365 10 false Intake Air Temperature Sensor 0.542,1.75 2.365,2.052 1.823,0.302 10 false Crankshaft Position Sensor 0.5,2.177 2.438,2.531 1.938,0.354 10 false VVT Sensor (Bank 1 Intake) 0.448,2.635 2.458,2.969 2.01,0.333 10 false VVT Sensor (Bank 1 Exhaust) 0.469,3.104 2.385,3.438 1.917,0.333 10 false VVT Sensor (Bank 2 Intake) 0.427,3.563 2.344,3.917 1.917,0.354 10 false VVT Sensor (Bank 2 Exhaust) 0.406,4.031 2.302,4.563 1.896,0.531 10 false Air Fuel Ratio Sensor (Bank 1, Sensor 1) 0.406,4.854 2.281,5.5 1.875,0.646 10 false Air Fuel Ratio Sensor (Bank 2, Sensor 1) 0.344,5.646 2.333,6.167 1.99,0.521 10 false Heated Oxygen Sensor (Bank 1, Sensor 2) 0.333,6.417 2.323,6.896 1.99,0.479 10 false Heated Oxygen Sensor (Bank 2, Sensor 2) 0.229,7.177 2.521,7.51 2.292,0.333 10 false Accelerator Pedal Sensor Assembly 0.26,7.76 2.427,8.25 2.167,0.49 10 false E.F.I. Engine Coolant Temperature Sensor 4.771,5.208 6.76,5.708 1.99,0.5 10 false Direct Fuel Injector Assembly 4.802,4.177 6.583,4.583 1.781,0.406 10 false Port Fuel Injector Assembly 4.698,2.156 6.615,2.656 1.917,0.5 10 false Fuel Pressure Sensor (for High Pressure) 4.688,1.417 6.563,1.854 1.875,0.438 10 false Fuel Pressure Sensor (for Low Pressure) 4.917,0.802 6.552,1.188 1.635,0.385 10 false Throttle Position Sensor 4.542,0.333 6.833,0.667 2.292,0.333 10 false Throttle Body with Motor Assembly 3.333,4.49 3.719,4.875 0.385,0.385 10 false ECM


g.

Fuel Cut

i.

When the engine speed exceeds the specified value, fuel injection is stopped to prevent over-revving.

Engine Speed for Fuel-cut at High Revs
Engine speed (rpm) 6300 or more