Home › Engine / Hybrid System › 7GR-FKS (ENGINE CONTROL) › SFI SYSTEM
NM35X0E _51 Engine / Hybrid System _079945 7GR-FKS ENGINE CONTROL _0389299 SFI SYSTEM DE DETAILS F

7GR-FKS ENGINE CONTROL  SFI SYSTEM  DETAILS  CRANKSHAFT POSITION SENSOR  


CONSTRUCTION


a.

A Magnetic Resistance Element (MRE) type crankshaft position sensor is used to detect the engine speed and crankshaft angle.


b.

The crankshaft angle sensor plate (timing rotor) of the crankshaft consists of 34 teeth with 2 teeth missing. The crankshaft position sensor outputs a crankshaft rotation signal every 10°, and the change of the signal due to the missing teeth is used to determine top-dead-center.

W142341E01
1.844,1.469 4.021,1.469 4.021,1.469 5.125,3.198 true 2.083,3.927 2.396,3.927 2.396,3.927 3.406,3.417 true 0.156,3.833 2.167,4.125 2.01,0.292 10 false Crankshaft Angle Sensor Plate 0.115,1.375 2.021,1.615 1.906,0.24 10 false Crankshaft Position Sensor 0.344,6.74 1.594,7.156 1.25,0.417 10 false Crankshaft Position Sensor 1,5.469 1.375,5.698 0.375,0.229 10 false ECM 3.5,5.51 4.042,5.719 0.542,0.208 10 false 30° CA 3.625,5.854 4.167,6.063 0.542,0.208 10 false 10° CA 3.771,6.729 4.031,6.938 0.26,0.208 10 false Lo 1.698,6.979 3.771,7.229 2.073,0.25 10 false Crankshaft Angle Sensor Plate 3.792,6.219 3.99,6.438 0.198,0.219 10 false Hi 4.75,7.125 5.938,7.365 1.188,0.24 10 false Output Waveforms 4.188,5.5 6.802,5.76 2.615,0.26 10 true Crankshaft Angle Sensor Plate (360° CA)


c.

An MRE type crankshaft position sensor consists of an MRE, a magnet and a sensor. The direction of the magnetic field changes due to the profile (protruding and non-protruding portions) of the crankshaft angle sensor plate, which passes by the sensor. As a result, the resistance of the MRE changes, and the output voltage to the ECM changes to high or low. The ECM detects the crankshaft position based on this output voltage.


d.

The differences between a MRE type sensor and the pick-up coil type sensor used on the conventional models are as follows:

·

The MRE type sensor outputs a constant level of high and low digital signals regardless of the engine speed. Therefore, the MRE type sensor can detect the positions of the crankshaft at an early stage of cranking.

·

The pick-up coil type sensor outputs analog signals with levels that change with the engine speed.


MRE Type and Pick-up Coil Type Output Waveform Image Comparison
W126804E01
4.292,3.083 4.292,2.667 true 4.656,1.896 4.656,1.031 4.656,1.031 4.823,1.031 true 0.01,1.125 0.938,1.417 0.927,0.292 10 false Engine Speed 3.01,1.104 3.938,1.396 0.927,0.292 10 false Engine Speed 0,2.74 0.927,3.031 0.927,0.292 10 false Sensor Output 3.021,2.438 3.948,2.729 0.927,0.292 10 false Sensor Output 2.104,3.125 2.99,3.354 0.885,0.229 10 false Digital Output 1.542,3.427 2.302,3.646 0.76,0.219 10 false MRE Type 4.76,3.469 5.729,3.688 0.969,0.219 10 false Pick-up Type 3.917,3.135 5.24,3.354 1.323,0.219 10 false Non Detection Area 6.031,2.708 7,2.948 0.969,0.24 10 false Analog Output 4.896,0.948 6.198,1.188 1.302,0.24 10 false Non Detection Area