CONSTRUCTION
The power slide door lock assembly consists mainly of a closer motor, latch, pawl, open cable, release cable, various levers and various switches.
The power slide door lock assembly fully closes the slide door automatically when the slide door is ajar.
When the slide door is fully closed, the open cable is pulled to disengage the latch in the power slide door lock assembly.
When the slide door is fully opened or closed, the closer motor in the power slide door lock assembly operates the slide door lock remote control assembly to drive a link mechanism such as the active lever and pull the release cable.
The power slide door lock assembly contains 5 switches to detect the locked state. The detection functions of the switches are the following:
| Detection Switch | Function |
|---|---|
| Half-latch Switch | Turns on from the time the latch is released, until just before it is at the half latch position, in order to detect the position of the latch. |
| Full-latch Switch | Turns off when the latch is in the full latch state, in order to detect the fully closed position of the latch. |
| Pawl Switch | Detects the position of the pawl, turns on when the latch is fully closed, and turns off when the latch is rotating. |
| Neutral Position Switch (Close) | Detects the active lever close operating range, and turns off when the active lever returns to its initial position. |
| Neutral Position Switch (Release) | Detects the active lever release operating range, and turns off when the active lever returns to its initial position. |
| *1 | Neutral Position Switch | *2 | Closer Motor |
| *3 | ·
Half-latch Switch ·
Full-latch Switch |
*4 | Pawl Switch |
| *1 | Neutral Position Switch Sub-assembly | *2 | Active Lever |
| *3 | Pinion | *4 | Passive Lever |
| *5 | Open Lever | *6 | Latch |
| *7 | Pawl | *8 | Lift Lever |
| *9 | Release Lever | - | - |
Neutral Position Switch
| *1 | Neutral Position Switch | *2 | Neutral Position Switch Gear |
| *3 | Active lever | - | - |
| *a | Full Release | *b | Release Operating Range |
| *c | Neutral Range | *d | Half Latch Range |
| *e | Half Latch Position | *f | Full Latch Position |
| *g | Over Latch Position | *h | Close Operating Range |
Half Latch, Full Latch Switch and Pawl Switch
| *1 | Pawl Switch | *2 | Half-latch Switch |
| *3 | Full-latch Switch | - | - |
| *a | Half Latch | *b | Full Latch |
| *c | Over Latch | *d | On |
| *e | Off | - | - |
OPERATION
Close Operation
The closer motor rotates according to each type of switch signal. When the closer motor causes the pinion (*2 in illustration) to start rotating, first, the active lever (*1 in illustration) that is engaged with the pinion (*2 in illustration) rotates, raising the passive lever (*3 in illustration).
| *1 | Active Lever | *2 | Pinion |
| *3 | Passive Lever | *4 | Latch |
Next, the raised passive lever (*3 in illustration) presses the latch (*4 in illustration) and the rotation of the latch (*4 in illustration) moves the slide door from ajar to fully closed.
| *1 | Active Lever | *2 | Pinion |
| *3 | Passive Lever | *4 | Latch |
Release Operation
The closer motor causes the pinion to rotate, rotating the active lever (*2 in illustration) to the release side. When the active lever (*2 in illustration) rotates, it engages with the release lever (*4 in illustration), causing the power slide door lock remote cable (*1 in illustration) to be pulled by the rotation of the release lever (*4 in illustration).
| *1 | Power Slide Door Lock Remote Cable | *2 | Active Lever |
| *3 | Pinion | *4 | Release Lever |
When the power slide door lock remote cable (*6 in illustration) is pulled by the release lever, the No. 6 slide door lock control lever (*5 in illustration) rotates. The No. 6 slide door lock control lever (*5 in illustration) presses and rotates the No. 5 slide door lock control lever (*3 in illustration) through the rod while simultaneously and directly pressing and rotating the slide door lock control lever sub-assembly (*2 in illustration).
| *1 | No. 2 Slide Door Lock Control Lever | *2 | Slide Door Lock Control Lever Sub-assembly |
| *3 | No. 5 Slide Door Lock Control Lever | *4 | Slide Door Lock Control Cable Assembly |
| *5 | No. 6 Slide Door Lock Control Lever | *6 | Power Slide Door Lock Remote Cable |
| *7 | Slide Door Closer Open Cable Assembly | *8 | Slide Door Control Cable Assembly |
When the slide door is fully open.
The No. 5 slide door lock control lever rotates, causing the pulled slide door lock control cable assembly to release the lock of the slide door full open stop lock assembly (*1 in illustration) and complete the release operation.
| *1 | Slide Door Full Open Stop Lock Assembly | *2 | Latch |
| *3 | Lock Ratchet | - | - |
| *a | Closed Condition | *b | Release Condition |
When the slide door is fully closed.
The rotation of the slide door lock control lever sub-assembly is transmitted to the No. 2 slide door lock control lever through the slide door remote control pin, pulling the slide door closer open cable assembly and slide door control cable assembly. First, the slide door control cable assembly releases the lock of the slide door front lock assembly (*1 in illustration) of the connection.
| *1 | Slide Door Front Lock Assembly | *2 | Latch |
| *3 | Lock Ratchet | - | - |
| *a | Closed Condition | *b | Release Condition |
At the same time, the slide door closer open cable assembly (*2 in illustration) pulled by the No. 2 slide door lock control lever rotates the open lever (*1 in illustration) of the power slide door lock assembly. Next, when the open lever (*1 in illustration) rotates, it presses the lift lever (*5 in illustration). The pawl (*4 in illustration) linked with the pressed lift lever (*5 in illustration) moves, releasing the latch (*3 in illustration) lock. As a result, the slide door fully opens and the release operation completes.
| *1 | Open Lever | *2 | Slide Door Closer Open Cable Assembly |
| *3 | Latch | *4 | Pawl |
| *5 | Lift Lever | - | - |