FUNCTION OF MAIN COMPONENTS
The main components of the power slide door system have the following functions:
| Component | Function | |
|---|---|---|
| Slide Door Motor Unit | Power Slide Door Motor | Controlled by the slide door ECU, the power slide door motor opens and closes the slide door. |
| Magnetic Clutch | Transmits the drive force of the power slide door motor to the power slide door motor belt. | |
| Pulse Sensor (Door Sensor) | Detects the operation conditions of the slide door and outputs a pulse signal to the slide door ECU. | |
| Slide Door ECU | Controls the slide door in accordance with the signal received from the switches, sensors and main body ECU (multiplex network body ECU). | |
| Buzzer | Sounds during system operation and malfunction. | |
| Slide Door Front Lock Assembly | Locks the slide door in the fully closed position when the slide door is fully closed. | |
| Power Slide Door Lock Assembly | Slide Door Closer Motor | ·
Controlled by the slide door ECU, the closer motor latches the slide door when the slide door is ajar. ·
Releases the lock condition of the slide door front lock assembly and power slide door lock assembly. |
| Full-latch Switch | Detects the latch position. | |
| Half-latch Switch | Detects the latch position. | |
| Pawl Switch | Detects the engagement of the pawl and latch. | |
| Neutral Position Switch (Close) | Detects the closer motor operation position. | |
| Neutral Position Switch (Release) | ||
| Slide Door Lock Remote Control Assembly | Inside Handle Switch (Open) | Detects the open operation condition of the slide door inside handle. |
| Outside Handle Switch (Open) | Detects the open operation condition of the slide door outside handle. | |
| Handle Switch (Close) | Detects the close operation condition of the slide door inside handle and outside handle. | |
| Inside Handle | Sends handle operations performed from inside the vehicle to the slide door lock remote control assembly through a wire. | |
| Outside Handle | Sends handle operations performed from outside the vehicle to the slide door lock remote control assembly through a link. | |
| Touch Sensor (Power Slide Door Sensor Assembly) | Detects jams during closing operation of the slide door and sends the result to the slide door ECU. | |
| Slide Door Switch (Open/Close) | Sends the operation signal to the main body ECU (multiplex network body ECU). | |
| Power Slide Door Main Switch | Setting this switch prohibits system operation.*1 | |
| Main Body ECU (Multiplex Network Body ECU) | Sends signals from each switch and ECU to the slide door ECU. | |
| ECM*2 | Sends the shift position signal to the main body ECU (multiplex network body ECU). | |
| Skid Control ECU | Sends the stop light switch assembly signal to the main body ECU (multiplex network body ECU). | |
| Door Control Receiver | Receives signals from the door control transmitter and sends them to the main body ECU (multiplex network body ECU). | |
| Door Control Transmitter Assembly
·
Power Slide Door Button |
Detects whether the power slide door button is operated and sends the operation status to the door control receiver. | |
| Park/Neutral Position Switch Assembly*2 | Sends shift position signals to the ECM. | |
| Stop Light Switch Assembly | Detects the brake pedal operation status and sends it to the skid control ECU. | |
| Parking Brake Switch Assembly | Detects the parking brake operation status and sends it to the main body ECU (multiplex network body ECU). | |
| Combination Meter Assembly | Sends the vehicle speed signal to the main body ECU (multiplex network body ECU). | |
*1: However, even when the power slide door main switch is turned off, the slide door closer function operates.
*2: Models with automatic transmission
OPERATING CONDITION
Operation of the power slide door system is possible when all of the following conditions are met.
| Ignition Switch | Operation Condition |
|---|---|
| On | ·
Power slide door main switch is on. ·
Slide door is unlocked.*1 ·
Shift lever is in P*2, brake pedal is depressed or parking brake is engaged.*3 ·
Vehicle speed is less than approximately 3 km/h (2 mph).*4 ·
Touch sensor (power slide door sensor assembly) is off.*5 |
| Off | ·
Power slide door main switch is on. ·
Slide door is unlocked.*1 ·
Vehicle speed is less than approximately 3 km/h (2 mph).*4 ·
Touch sensor (power slide door sensor assembly) is off.*5 |
*1: Except during wireless operation
*2: Models with automatic transmission
*3: Only during open operation
*4: During slide door open operation
*5: During slide door close operation
When operation conditions are not met, the slide door ECU stops operation of the slide door and sounds the buzzer to warn the driver.
| Slide Door Condition | Operation Conditions not Met | Control | Buzzer Operation |
|---|---|---|---|
| Slide Door Stopped → When Operated | Power slide door main switch is on. | Operation does not start | Sounds 2 times for 0.13 seconds*1 |
| Any of the following conditions are not met:
·
Slide door is unlocked.*2 ·
Shift lever is in P*3, brake pedal depressed or parking brake engaged.*2 |
Operation does not start or strong brake/clutch control activates*4 | Sounds 2 times for 0.13 seconds*5 | |
| Vehicle speed is less than approximately 3 km/h (2 mph). | Operation does not start or suspend control (magnetic clutch is engaged) activates*6 | Sounds 2 times for 0.13 seconds*5 | |
| During Slide Door Open Operation | Power slide door main switch is on. | Operation stops or strong brake/clutch control activates | Sounds 1 time for 2 seconds |
| Vehicle speed is less than approximately 3 km/h (2 mph). | Operation stops or suspend control (magnetic clutch is engaged) activates | Sounds 1 time for 2 seconds | |
| During Slide Door Close Operation | Power slide door main switch is on. | Operation stops or strong brake/clutch control activates | Sounds 1 time for 2 seconds |
| Touch sensor (power slide door sensor assembly) is on. | Operation stops |
*1: If operated with the slide door inside handle or slide door outside handle, the buzzer will not sound.
*2: Only during open operation
*3: Models with automatic transmission
*4: When the slide door inside handle or slide door outside handle is manually operated to open or close the slide door, the buzzer sounds for approximately 2 seconds.
*5: If the slide door unlock conditions are not met when an open or close operation is started with the slide door inside handle or slide door outside handle while the slide door is fully closed, the buzzer will not sound.
*6: When the slide door inside handle or slide door outside handle is manually operated to open or close the slide door, the system engaged the magnetic clutch. In this case, the buzzer sounds for approximately 2 seconds.
FUNCTION
Power Slide Door System Function List
| Function | Outline |
|---|---|
| Slide Door Closer Function | When the power slide door main switch is off and the slide door is ajar, this function automatically moves the slide door to the fully closed position. |
| Power Slide Door Wireless One-motion Open | Pressing the power slide door button of the door control transmitter assembly when the slide door is locked, all doors are unlocked and the power slide door is opened. |
| Reserve Lock Function | When a door other than the slide door is closed and the door lock is operated by the lock sensor of the front door outside handle assembly or the door control transmitter assembly during a slide door auto close operation, a door lock operation is performed at that time. The door lock operation completes when the slide door close operation ends. |
| Customized Function | A Global TechStream (GTS) can be used to customize the settings. For details, refer to the Repair Manual. |
The power slide door system has the following controls:
| Control | Outline |
|---|---|
| Auto Opener/Closer Control | The slide door automatically opens and closes when any of the following are operated.
·
Slide door switch (open/close) ·
Power slide door button of the door control transmitter assembly ·
Slide door inside handle or slide door outside handle |
| Jam Protection Control | If an overload is applied during a slide door open or close operation, or a jam is detected, the slide door open or close operation reverses, and then stops. |
| Suspended Control | When any of the following is operated during a slide door auto open or close operation, the slide door stops operating and the magnetic clutch is engaged.
·
Slide door switch (open/close) ·
Power slide door button of the door control transmitter assembly ·
Slide door inside handle or slide door outside handle |
| Brake/Clutch Control | If the speed of the slide door reaches or exceeds a specified value when the slide door is opening or closing (with the power slide door main switch off), the magnetic clutch is operated in order to reduce the slide door moving speed. |
| Strong Brake/Clutch Control | When manual mode (manual opening and closing of the slide door) is activated due to a system malfunction, etc., if the moving speed of the slide door is at a specified value or more or when it deviates from the operating condition, the magnetic clutch is operated in order to reduce the slide door moving speed. |
| Intermittent Clutch Control | If a pulse sensor (door sensor) malfunction is detected during a slide door open or close operation, the magnetic clutch intermittently operates to slow the speed of the slide door. |
| Slide Door Open/Close Speed Control | The slide door ECU operates at low speed control to reduce the jam impact during a fully closed condition and to reduce the shock during a fully opened condition. |
SYSTEM CONTROL
Auto Opener/Closer Control
Opener/closer control by slide door switch (open/close) operation
| Switch Operation | Slide Door Condition | Control |
|---|---|---|
| Open On
(Held for 0.5 Seconds or More) |
Fully closed | Auto open*1 |
| Fully open | Does not operate | |
| Operation suspended | Auto open*1 | |
| During open operation | Suspended | |
| During close operation | Suspended*2 | |
| Close On
(Held for 0.5 Seconds or More) |
Fully closed | Does not operate |
| Fully open | Auto close*1 | |
| Operation suspended | Auto close*1 | |
| During open operation | Suspended*2 | |
| During close operation | Suspended |
*1: Buzzer sounds simultaneously for 0.8 seconds when operation starts.
*2: When switch operation is detected, slide door operation stops for a maximum of 3 minutes (magnetic clutch engaged).
Opener/closer control by power slide door button of door control transmitter assembly operation
| Button or Switch Operation | Slide Door Condition | Control |
|---|---|---|
| Power Slide Door Button On
(Held for 0.8 Seconds or More)*1 |
Fully close | Auto open*2, *3 |
| Fully open | Auto close*2, *3 | |
| During open or close operation | Stop*4 | |
| Close operating suspended | Auto open*2, *3 | |
| Open operating suspended | Auto open*2, *3 |
*1: Fully close or fully open condition
*2: Buzzer sounds simultaneously for 0.8 seconds when operation starts.
*3: Slide door open and close operations cannot be performed if the ignition switch is ON.
*4: When button is detected, slide door operation stops for a maximum of 3 minutes (magnetic clutch engaged).
Opener/closer control by slide door inside handle or slide door outside handle operation
| Handle Operation | Slide Door Condition | Control |
|---|---|---|
| Slide Door Inside Handle Operated toward Rear (Slide Door Open Direction)*1 | Fully closed | Auto open*2 |
| Fully open | Does not operate | |
| During open operation | Suspended | |
| During close operation | Suspended*3 | |
| Operation suspended | Auto open*2 | |
| Slide Door Inside Handle Operated toward Front (Slide Door Close Direction)*1 | Fully closed | Does not operate |
| Fully open | Auto close*2 | |
| During open operation | Suspended*3 | |
| During close operation | Suspended | |
| Operation suspended | Auto close*2 | |
| Slide Door Outside Handle toward Rear (Slide Door Open Direction)*1 | Fully closed | Auto open*2 |
| Fully open | Does not operate | |
| During open operation | Suspended | |
| During close operation | Suspended*3 | |
| Operation suspended | Auto open*2 | |
| Slide Door Outside Handle toward Front (Slide Door Close Direction)*1 | Fully closed | Does not operate |
| Fully open | Auto close*2 | |
| During open operation | Suspended*3 | |
| During close operation | Suspended | |
| Operation suspended | Auto close*2 |
*1: When the slide door is fully closed, operate the handle until the latch is securely released (door becomes ajar).
*2: Buzzer sounds simultaneously for 0.8 seconds when operation starts.
*3: When handle operation is detected, slide door operation stops for a maximum of 3 minutes (magnetic clutch engaged).
Jam Protection Control
The slide door ECU detects whether an overload has been applied to the power slide door by the change in the touch sensor (power slide door sensor assembly) or power slide door motor current value. When this occurs, the slide door ECU reverses, and then stops the slide door.
| Detection Method | Control | |
|---|---|---|
| Touch sensor (power slide door sensor assembly) output signal | During close operation | Reverses 100 mm (3.94 inc) and stops*1, *2 or full open*3 |
| Change in power slide door motor current value | During close operation | Reverses 100 mm (3.94 inc) and stops*1, *2 or full open*3 |
| During open operation | Reverses 100 mm (3.94 inc) and stops*2 | |
*1: Except models for Australia
*2: Slide door operation stops for a maximum of 30 minutes (magnetic clutch engaged). If 30 minutes elapse, the buzzer sounds for 2 seconds and the system activates strong brake/clutch control to prevent battery depletion.
*3: For models for Australia, the slide door reverses operation until it is fully open.
Brake/Clutch Control
If the speed of the slide door reaches or exceeds a specified value by manual open or close operation of the slide door or through the weight of the slide door, the power slide door motor stops and the magnetic clutch is operated in order to reduce the slide door moving speed.
Brake/clutch control operates regardless of whether the power slide door main switch is on or off.
When the following condition is met, brake/clutch control starts. Also, brake/clutch control is ended by fully closing the slide door.
·
Slide door is not in the fully closed position. |
Strong Brake/Clutch Control
When manual mode (manual opening and closing of the slide door) is activated, if the moving speed of the slide door is at a specified value or more, the magnetic clutch is operated in order to reduce the slide door moving speed.
When any of the following conditions are met and the moving speed of the slide door via manual operation is at a specified value (approximately 0.25 m/sec.) or more, strong brake/clutch control activates.
·
The operation conditions are not met during a slide door open operation. ·
The operation conditions are not met during a slide door close operation. ·
A certain period of time elapses after suspend control. ·
The power slide door main switch is turned off during suspend control. |
When any of the following conditions are met after strong brake/clutch control activates, control ends.
·
Approximately 9.9 seconds elapse after control starts. ·
The slide door does not move for approximately 1 second. ·
The slide door closer function operates (when the power slide door main switch is on). ·
The slide door is fully closed. |
Intermittent Clutch Control
When the speed of the slide door cannot be detected due to a pulse sensor (door sensor) malfunction, the magnetic clutch operates intermittently and slows the slide door.
Intermittent clutch control starts when the following condition is met. If approximately 70 seconds elapse after control starts or the slide door fully closes, intermittent clutch control is ended.
·
A pulse sensor (door sensor) malfunction is detected during a slide door open or close operation. |
FAIL-SAFE
If a system malfunction occurs, the system activates strong brake/clutch control or intermittent clutch control depending on the cause of the malfunction. For details, refer to the Repair Manual.
DIAGNOSIS
When the slide door ECU detects a malfunction in the power slide door system, it diagnosis the failed section. For details, refer to the Repair Manual.