CONSTRUCTION
Back Door Lock Assembly
The back door lock assembly consists of 3 position detection switches (initial position switch, half/full latch switch and courtesy switch), back door closer motor, lock driven gear, lock hook lever, latch and lock ratchet.
The rotation of the back door closer motor is transmitted to the lock hook lever via the back door lock driven gear. The lock hook lever operates the latch to engage the striker.
| *1 | Back Door Closer Motor | *2 | Release Lever |
| *3 | Half/Full Latch Switch | *4 | Lock Ratchet |
| *5 | Latch | *6 | Courtesy Switch |
| *7 | Lock Hook Lever | *8 | Initial Position Switch |
| *9 | Lock Driven Gear | - | - |
Initial Position Switch
The initial position switch turns off when the lock driven gear and back door closer motor are in the initial position and turns on when the back door closer motor is operated.
| *1 | Lock Driven Gear | *2 | Initial Position Switch |
| *a | Initial Position | *b | When Back Door Closer Motor Operated |
| *c | Off | *d | On |
Half/Full Lock Switch and Courtesy Switch
The half/full lock switch and courtesy switch turn on when the back door is open.
The half/full lock switch turns off and the courtesy switch turns on when the back door is ajar.
The courtesy switch turns off when the back door is fully closed.
The half/full lock switch turns on and courtesy switch turns off when the full latch condition is detected.
| *1 | Lock Hook Lever | *2 | Courtesy Switch |
| *3 | Half/Full Latch Switch | *4 | Latch |
| *a | Open Condition | *b | Ajar Condition |
| *c | Closed Condition | *d | On |
| *e | Off | - | - |
OPERATION
Fully Close Operation
When the back door becomes ajar, each built-in detection switch detects the ajar position and the back door closer motor performs an engagement operation to fully close the back door.
| *1 | Back Door Closer Motor | *2 | Lock Ratchet |
| *3 | Latch | *4 | Lock Hook Lever |
| *5 | Lock Driven Gear | *6 | Pinion |
| *a | Lower View | *b | Ajar Condition |
| *c | Initial Position | - | - |
The back door closer motor rotates in the engagement direction with each gear in the initial position, transmitting rotation to the pinion.
The lock driven gear is linked with the pinion and rotates in the engagement direction, and since the lock hook lever is held in place by the lock driven gear, the latch also rotates in the engagement direction. As a result, the striker is pulled in, fully closing the back door from the ajar position. Afterward, latch rotation is prevented by the lock ratchet.
| *1 | Back Door Closer Motor | *2 | Lock Ratchet |
| *3 | Latch | *4 | Lock Hook Lever |
| *5 | Lock Driven Gear | *6 | Pinion |
| *a | Lower View | *b | Rotation Operation in Engagement Direction |
| *c | Closed Condition | *d | Engagement Direction |
After the fully close operation completes, the back door closer motor performs a reverse rotation operation to return each gear to the initial position.
| *1 | Back Door Closer Motor | *2 | Lock Ratchet |
| *3 | Latch | *4 | Lock Hook Lever |
| *5 | Lock Driven Gear | *6 | Pinion |
| *a | Lower View | *b | Reverse Rotation Operation |
| *c | Closed Condition | *d | Initial Position |
Open Operation
The open lever is operated, the release lever is pulled by the wire.
When the release lever moves the lock ratchet, the latch lock is release and the back door opens.
| *1 | Back Door Open Cable Assembly | *2 | Release Lever |
| *3 | Lock Ratchet | *4 | Latch |