Home › Engine / Hybrid System › 1GD-FTV (EMISSION CONTROL) › EMISSION CONTROL SYSTEM
NM35X0E _51 Engine / Hybrid System _080142 1GD-FTV EMISSION CONTROL _0389536 EMISSION CONTROL SYSTEM CO CONTROL F

1GD-FTV EMISSION CONTROL  EMISSION CONTROL SYSTEM  CONTROL  CATALYST SUPPORT CONTROL  


SYSTEM CONTROL


a.

In order to regenerate the DPF, the temperature of the DPF is increased to combust the accumulated PM in the DPF, expelling it as CO2 and H2O.


b.

If the temperature of the DPF does not increase and the PM keeps accumulating in the DPF, a message and the amount of accumulated PM (in 10 levels) are simultaneously displayed on the multi-information display to notify the driver.


c.

The ECM monitors the engine condition and calculates the total amount of accumulated PM. In addition, the ECM calculates the amount of combusted PM according to the engine speed, fuel injection volume and the injection volume of the exhaust fuel addition injector assembly. The amount of accumulated PM in the DPF is calculated based on the calculated total amount of accumulated PM and the amount of combusted PM. The ECM urges the driver to perform PM automatic or manual regeneration according to the level of accumulated PM.


d.

When automatic or manual regeneration is performed, the injection of the exhaust fuel addition injector assembly and the engine combustion condition are controlled, increasing the temperature of the DPF. As a result, the temperature of the DPF becomes approximately 600°C to 700°C and PM is combusted.


e.

When the vehicle is continuously driven with a high exhaust temperature such as at high speeds, the temperature of the DPF is sufficiently increased and PM is spontaneously combusted. At this time, no special control such as exhaust fuel addition injector assembly control, etc. is performed.


f.

When the vehicle is continuously driven while the temperature of the DPF is not high enough for PM combustion such as when driving for a short distance or driving for a short time, catalyst performance is decreased. As a result, PM is accumulated in the DPF. When the amount of accumulated PM exceeds the threshold (for automatic regeneration), the ECM performs automatic regeneration until the amount of PM reaches zero.


g.

If the vehicle continues to be driven for a short distance even after automatic regeneration is performed, more PM is accumulated. When the amount of accumulated PM exceeds the threshold (for manual regeneration), a message and the amount of accumulated PM are simultaneously displayed on the multi-information display to urge the driver to perform manual regeneration.


h.

Automatic Regeneration

i.

When automatic regeneration is being performed, the ECM controls the fuel injection of the exhaust fuel addition injector assembly and the engine combustion condition, increasing the temperature of the DPF to combust the PM. Idle up is performed while the vehicle is stopped.

HINT:

The end of automatic regeneration is calculated by the ECM according to the amount of accumulated PM.




i.

Manual Regeneration

i.

The following methods are used to perform manual regeneration. For details of manual regeneration operation, refer to the Repair Manual.

1.

DPF Switch Operation Method

Stop the vehicle and press the DPF switch to perform manual regeneration.

HINT:

Operating the accelerator pedal (models with an automatic transmission) or operating the clutch pedal and accelerator pedal (models with a manual transmission) while regeneration is being performed temporarily stops regeneration.



2.

Global TechStream (GTS) Operation Method

Stop the vehicle and operate the Global TechStream (GTS) to perform manual regeneration.




ii.

When manual regeneration is being performed, the ECM controls the fuel injection of the exhaust fuel addition injector assembly and the engine combustion condition and performs idle up, increasing the temperature of the DPF to combust the PM.

HINT:

The end of manual regeneration is calculated by the ECM according to the amount of accumulated PM.




j.

Fail-safe

i.

If manual regeneration is performed when the amount of accumulated PM is beyond the threshold, the DPF may get damaged. Therefore, when the amount of accumulated PM exceeds the threshold (for the fail-safe function), the injection volume is controlled to a minimum level to cancel regeneration control. As a result, manual regeneration cannot be performed properly. At the same time, the MIL illuminates and a message is displayed on the multi-information display to notify the driver of a malfunction.

Relationship between MIL, Message on Multi-information Display and Regeneration Control (Conceptual Diagram)
W142585E01
2.635,4.177 2.865,4.177 2.865,4.177 2.938,3.563 true 1.948,1.094 2.094,1.094 2.094,1.094 2.552,1.438 true 2.031,0.646 2.177,0.646 2.177,0.646 2.552,1.094 true 0.531,0.052 2.219,0.344 1.688,0.292 10 false : Automatic regeneration 3.688,0.052 5.375,0.344 1.688,0.292 10 false : Manual regeneration 0.052,1.677 0.927,2.573 0.875,0.896 10 false PM Accumulation 0.521,0.583 2.021,0.99 1.5,0.406 10 false Threshold (for Fail-safe) 0.552,1.021 1.896,1.552 1.344,0.531 10 false Threshold (for Manual Regeneration) 0.99,2.729 2.563,3.333 1.573,0.604 10 false Threshold (for Automatic Regeneration) 2.625,0.781 4.458,1.115 1.833,0.333 10 false Fail-safe Range 2.594,1.104 4.427,1.438 1.833,0.333 10 false Manual Regeneration Range 1.104,4.094 2.698,4.406 1.594,0.313 10 false Normal Operation Range 6.646,2.479 6.802,2.677 0.156,0.198 10 false A 6.677,1.521 6.833,1.719 0.156,0.198 10 false B 6.646,1.177 6.802,1.375 0.156,0.198 10 false C 6.646,0.865 6.802,1.063 0.156,0.198 10 false D 3.99,3.698 5.427,4.229 1.438,0.531 10 false Traveled Distance 2.573,1.438 4.823,1.688 2.25,0.25 10 false Automatic Regeneration Range

Text in Illustration MIL Message on Multi-information Display
A - -
Manual Regeneration Unavailable DPF Normal
B - DPF Full See Owner's Manual
C - DPF Full Manual Regeneration Required See Owner's Manual
D Illuminate DPF Full Visit Your Dealer

W142466C01
2.135,1.313 3.344,1.229 true 5.021,1.344 6.333,0.865 true 1.219,0.563 1.531,0.719 0.313,0.156 10 false *1 0.417,2.302 0.906,2.5 0.49,0.198 10 false *2 3.417,1.125 3.896,1.333 0.479,0.208 10 false *3 0.292,0.052 0.844,0.292 0.552,0.24 12 false *A: 3.594,0.083 4.146,0.323 0.552,0.24 12 false *B: 5.104,0.542 5.417,0.698 0.313,0.156 10 false *1 6.531,2.302 7.021,2.5 0.49,0.198 10 false *2 6.385,0.74 6.865,0.948 0.479,0.208 10 false *3
*A LHD Models *B RHD Models
*1 MIL *2 DPF Switch Assembly
*3 Multi-information Display - -