Home › Engine / Hybrid System › 1GD-FTV (INTAKE / EXHAUST) › INTAKE SYSTEM
NM35X0E _51 Engine / Hybrid System _080143 1GD-FTV INTAKE / EXHAUST _0389537 INTAKE SYSTEM DE DETAILS F

1GD-FTV INTAKE / EXHAUST  INTAKE SYSTEM  DETAILS  TURBOCHARGER  


CONSTRUCTION


a.

A variable nozzle vane type turbocharger sub-assembly is used. A water jacket is provided in the bearing housing to improve the cooling performance of the turbocharger sub-assembly.


b.

The shape of the turbine wheel is optimized for downsizing, improving higher rotational speed, and dynamic response and transitioning performance, as well as reducing fuel consumption and exhaust gas emissions. Also, a full-back disk is used for the turbine wheel to improve reliability of the turbine wheel and allow exhaust gas to flow smoothly to the turbine wheel, improving turbo efficiency and reducing fuel consumption.


c.

This turbocharger sub-assembly has achieved great improvements in low-speed torque, maximum output, fuel consumption and emission reduction. These improvements have been accomplished through variable control of the nozzle vane position, and an optimal velocity of the exhaust gas inflow to the turbine at all times in response to the engine condition.


d.

The variable nozzle vane type turbocharger sub-assembly consists primarily of a compressor wheel, turbine wheel, nozzle vane, unison ring, drive arm, driven arm, actuator (motor and nozzle vane position sensor) and nozzle vane control link.


e.

The ECM outputs a signal to the turbocharger sub-assembly, which operates the actuator to control the nozzle vane position.

W123669C01
3.646,0.896 4.427,1.354 true 5.906,1.344 6.396,0.792 true 5.719,1.76 6.385,1.948 true 5.49,2 6.292,2.594 true 5.333,3.219 5.458,2.896 true 5.958,3.365 6.458,3.219 true 5.573,4.021 6.104,4.406 true 5.24,4.25 5.583,4.563 true 4.073,3.115 4.552,3.469 true 2.656,1 2.917,0.594 true 1.948,1.833 1.677,0.594 true 0.792,0.625 1.167,1.521 true 0.656,0.438 0.969,0.594 0.313,0.156 10 false *1 2.917,0.417 3.229,0.573 0.313,0.156 10 false *2 1.542,0.396 1.854,0.552 0.313,0.156 10 false *3 3.49,0.76 3.802,0.917 0.313,0.156 10 false *4 6.323,2.531 6.635,2.688 0.313,0.156 10 false *5 6.427,1.875 6.75,2.052 0.323,0.177 10 false *6 6.396,0.625 6.708,0.813 0.313,0.188 10 false *7 6.146,4.333 6.458,4.49 0.313,0.156 10 false *8 5.438,2.677 5.76,2.854 0.323,0.177 10 false *9 3.927,2.979 4.24,3.167 0.313,0.188 10 false *7 5.625,4.49 5.948,4.667 0.323,0.177 10 false *6 6.49,3.083 6.823,3.271 0.333,0.188 10 false *3
*1 Turbocharger Sub-assembly *2 Actuator
*3 Linkage *4 Compressor Wheel
*5 Unison Ring *6 Nozzle Vane
*7 Turbine Wheel *8 Drive Arm
*9 Driven Arm - -




OPERATION


a.

The exhaust gas from the exhaust manifold goes through the nozzle vane inside the turbocharger housing and flows to the exhaust pipe through the turbine. The speed of the turbine (supercharging pressure) differs depending on the flow velocity of the exhaust gas going through the turbine, and the flow velocity of the exhaust gas is controlled by the opening. When there is less exhaust gas, such as during idling, the nozzle vane is almost fully closed, but as there is a slight clearance between the vanes, the exhaust gas flows through this clearance to the exhaust pipe. Therefore, there is no bypass.

W123704C01
4.104,0.302 4.323,0.146 4.323,0.146 4.479,0.146 true 4.094,1.208 4.302,1.5 4.302,1.5 4.448,1.5 true 4.521,0.031 4.833,0.229 0.313,0.198 10 false *1 4.5,1.385 4.813,1.583 0.313,0.198 10 false *1
*1 Nozzle Vane - -
V100136

Intake Air
V100135

Exhaust Gas



b.

At Low Load Range or Low Speed Range

i.

The actuator moves the linkage in the closing direction of the nozzle vanes in accordance with signals from the ECM.


ii.

This results in increasing the velocity of the exhaust gas flowing to the turbine, as well as the speed of the turbine. As a result, torque is improved when the engine is running at low speeds.

W123670C01
2.875,1.844 3.719,1.344 true 2.854,2.115 3.792,2.667 true 5.26,1.323 5.396,0.677 true 5.531,1.719 5.74,0.958 true 6.156,1.604 6.531,1.167 true 6.104,3.042 5.813,2.469 true 5.76,3.292 5.49,2.688 true 4.594,3.031 4.927,2.583 true 3.823,2.604 4.135,2.76 0.313,0.156 10 false *1 4.448,2.927 4.76,3.083 0.313,0.156 10 false *2 6.104,3.031 6.417,3.198 0.313,0.167 10 false *3 5.698,0.76 6.01,0.938 0.313,0.177 10 false *4 5.344,0.479 5.656,0.688 0.313,0.208 10 false *5 6.531,0.99 6.844,1.188 0.313,0.198 10 false *6 3.75,1.188 4.104,1.365 0.354,0.177 10 false *a 5.729,3.292 6.052,3.458 0.323,0.167 10 false *1
*1 Nozzle Vane *2 Turbine Wheel
*3 Drive Arm *4 Driven Arm
*5 Unison Ring *6 Linkage
*a Exhaust Gas Flow - -




c.

At High Load Range or Medium-to-high Speed Range

i.

The actuator moves the linkage in the opening direction of the nozzle vanes in accordance with signals from the ECM. This opens the nozzle vane and holds the specified supercharging pressure, lowering the back pressure and improving the output and fuel consumption.

W123671C01
2.958,1.854 3.792,1.375 true 2.833,2.083 3.854,2.531 true 4.927,2.552 4.542,3.031 true 5.521,2.667 5.854,3.292 true 5.771,2.302 6.26,2.802 true 5.198,1.323 5.281,0.729 true 5.531,1.656 5.719,0.979 true 6.458,1.156 6.188,1.583 true 3.896,2.448 4.208,2.604 0.313,0.156 10 false *1 4.385,2.948 4.698,3.104 0.313,0.156 10 false *2 6.292,2.74 6.604,2.896 0.313,0.156 10 false *3 5.688,0.792 6.01,0.969 0.323,0.177 10 false *4 5.219,0.552 5.531,0.708 0.313,0.156 10 false *5 6.458,0.958 6.771,1.115 0.313,0.156 10 false *6 3.833,1.219 4.146,1.396 0.313,0.177 10 false *a 5.833,3.281 6.146,3.438 0.313,0.156 10 false *1
*1 Nozzle Vane *2 Turbine Wheel
*3 Drive Arm *4 Driven Arm
*5 Unison Ring *6 Linkage
*a Exhaust Gas Flow - -