Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM › from 2019.06
NM35X0E _51 Engine / Hybrid System _078342 CRUISE CONTROL _0395949 LANE DEPARTURE ALERT SYSTEM CO CONTROL F

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM  CONTROL  LANE DEPARTURE ALERT CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The main components in the lane departure alert system have the following functions:

Components Function
Forward Recognition Camera
·

Controls the lane departure alert system.

·

Captures a view of the road ahead of the vehicle and detects lane markers or lane boundaries on the driving lane, and calculates the radius to the center of the lane, lane width, distance from markers and heading angle deviation.

·

Sends the indicator illumination request signal, multi-information display indication request signal, and meter buzzer sound request signal to the combination meter assembly.

·

Controls the supply of electric current to the camera heater when the ambient temperature is low.


Camera Heater (Forward Recognition Hood with Heater Sub-assembly) Uses electricity from the forward recognition camera to generate heat, removing fog and preventing the windshield glass in front of the forward recognition camera from fogging up.
Steering Vibration ECU Operates the steering wheel motor according to an eccentric motor operation request signal from the forward recognition camera.
Steering Wheel Motor Operates according to a signal from the steering vibration ECU to vibrate the steering wheel assembly.
Millimeter Wave Radar Sensor Assembly Radiates millimeter waves forward, uses the reflected waves to detect the presence of a vehicle traveling ahead, the vehicle-to-vehicle distance, and the relative speed, and then sends this information to the forward recognition camera.
Combination Meter Assembly - Sends a turn signal command to the forward recognition camera.
LDA Indicator Illuminates in accordance with signals from the forward recognition camera.
Multi-information Display Displays a warning message and white lines to inform or warn the driver of the system condition in accordance with signals from the forward recognition camera.
Meter Buzzer Sounds to warn the driver in accordance with signals from the forward recognition camera.
ECM Sends the shift position signal to the forward recognition camera.
Brake Actuator Assembly Skid Control ECU Sends a vehicle speed signal to the forward recognition camera.
Steering Pad Switch Assembly LDA Main Switch Detects the on/off status of the lane departure alert system and sends a signal to the forward recognition camera.
Airbag ECU (Airbag Sensor Assembly) Yawrate Sensor Detects the yaw rate and sends a signal to the forward recognition camera.
Steering Sensor
·

Sends the turning angle of the steering wheel to the forward recognition camera.

·

Sends a turn signal command to the combination meter assembly.


Turn Signal Switch Sends a turn signal command to the steering sensor.
Central Gateway ECU (Network Gateway ECU) Relays the signal between the CAN communication buses.
DLC3 The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions.



OPERATION CONDITION


a.

Operating Conditions of Lane Departure Alert Function

Operation Condition
Operating The lane departure alert function is activated when all of the following conditions are met:
·

The LDA main switch is on. (When the LDA main switch is pressed to turn on the lane departure alert system, the LDA indicator illuminates in white.)

·

The vehicle speed is approximately 50 km/h (32 mph) or more.

·

Lane marker or lane boundary is detected.

·

No turn signal command is detected.

·

A system malfunction is not detected.


Suspended The lane departure alert function is suspended when any one of the following conditions is met:
·

The vehicle speed is less than approximately 50 km/h (32 mph).

·

A turn signal command is detected.

·

No lane markers or lane boundaries are detected.

·

The yawrate sensor is malfunctioning.

·

The vehicle crosses halfway or further over a lane marker.

·

Immediately after the lane departure alert system is activated.

·

Detection of the curve radius other than regulated.

·

A malfunction is detected in the lane departure alert system.

·

The temperature of the forward recognition camera is abnormal.

·

Detection of the lane width other than regulated.


Canceled/Resume The lane departure alert function is stopped when any one of the following conditions is met:
·

The LDA main switch is off.

·

The lane departure alert system is temporarily stopped.

·

The lane departure alert system is malfunctioning.

·

The engine switch is turned off.


The lane departure alert function resumes when the following conditions are met:
·

The conditions to start operation listed above returns to be satisfied.

·

The lane departure alert system condition returns to normal.

·

The engine switch is turned off and on (IG) again to ensure normal operation, after the lane departure alert system has been stopped by a system malfunction.




b.

Operating Conditions of Vehicle Sway Warning Function

Operation Condition
Operating The vehicle sway warning function is activated when all of the following conditions are met:
·

Sway warning is turned "ON" via customized combination meter assembly settings.

·

The vehicle speed is approximately 50 km/h (32 mph) or more.

·

Lane markers are detected.

·

No turn signal command is detected.

·

A system malfunction is not detected.


Suspended The vehicle sway warning function is suspended when any one of the following conditions is met:
·

The vehicle speed is less than approximately 50 km/h (32 mph).

·

One side of lane markers is not detected.

·

The yawrate sensor is malfunctioning.

·

Immediately after the lane departure alert system is activated.

·

Detection of the curve radius other than regulated.

·

A malfunction is detected in the lane departure alert system.

·

The temperature of the forward recognition camera is abnormal.

·

Detection of the lane width other than regulated.

·

A turn signal command is detected.


Canceled/Resume The vehicle sway warning function is stopped when any one of the following conditions is met:
·

The lane departure alert system is temporarily stopped.

·

The lane departure alert system is malfunctioning.

·

The engine switch is turned off.

·

Sway warning is turned "OFF" via customized combination meter assembly settings.


The vehicle sway warning function resumes when the following conditions are met:
·

The conditions to start operation listed above returns to be satisfied.

·

The lane departure alert system condition returns to normal.

·

The engine switch is turned off and on (IG) again to ensure normal operation, after the lane departure alert system has been stopped by a system malfunction.

·

Sway warning is turned "ON" via customized combination meter assembly settings.





SYSTEM CONTROL


a.

Lane Departure Alert System Warning Operation

i.

Function Overview (Lane Departure Alert Function)

·

If the lane departure alert system judges that the vehicle may deviate from the lane it is in, the lane departure alert system illuminates the indicator in the combination meter display and vibrates the steering wheel or sounds a buzzer so that the driver can take action to avoid lane departure.

Y221925E08
2,4.021 1.625,3.313 1.625,3.313 1.281,3.313 true 5.042,0.219 5.573,0.542 0.531,0.323 10 false Warning 3.896,1.198 4.375,1.49 0.479,0.292 10 false Buzzer 5.083,1.208 5.563,1.5 0.479,0.292 10 false Display 6.229,1.146 6.813,1.448 0.583,0.302 10 false Vibration 5.031,3.146 5.563,3.469 0.531,0.323 10 false Warning 3.979,4.083 4.458,4.375 0.479,0.292 10 false Buzzer 5.104,4.146 5.583,4.438 0.479,0.292 10 false Display 6.229,4.104 6.813,4.406 0.583,0.302 10 false Vibration 0.271,3.219 1.354,3.49 1.083,0.271 10 false Grass, Dirt, etc.

HINT:

This illustration is only for explanatory purposes.




ii.

Function Overview (Vehicle Sway Warning Function)

·

The lane departure alert system detects drift of the vehicle within its lane, which is often the result of a driver who is tired, distracted or not looking ahead, based on the position of the vehicle within its lane and the steering inputs of the driver, to alert the driver before a lane departure or collision occurs.

Y180903E08
4.917,1.531 5.521,1.833 0.604,0.302 10 false Warning 4.396,2.021 4.906,2.354 0.51,0.333 10 false Buzzer 0.094,2.375 3.135,2.76 3.042,0.385 10 false This illustration is only for explanatory purposes. 5.448,2.052 5.948,2.375 0.5,0.323 10 false Display

·

The vehicle sway warning function provides a warning to alert the driver when any of the following conditions occur:

Y233275E05
0.208,3.302 5.104,3.5 4.896,0.198 10 false This illustration is an example. 4.781,1.927 5.979,2.469 1.198,0.542 10 false Would You Like to Take a Break? 5.24,0.208 5.958,0.5 0.719,0.292 10 false Display 1.771,0.167 3.521,0.479 1.75,0.313 10 false Type of vehicle swaying 1.073,1.219 4.063,1.677 2.99,0.458 10 false The vehicle drifts within its lane when the driver is inattentive. 1.083,2.469 3.927,2.917 2.844,0.448 10 false The steering wheel is turned abruptly when the driver is inattentive.





FUNCTION


a.

The lane departure alert system can be turned on/off by pressing the LDA main switch on the steering pad switch assembly while the engine is started.

HINT:

When the engine switch is turned from off to on (IG), the lane departure alert system turns on.


Y240848C01
3.24,2.021 6.115,1.448 true 6.177,1.344 6.49,1.5 0.313,0.156 10 false *a
*a LDA Main Switch - -



b.

Lane Departure Alert System Settings Functions Customization

Item Description Setting
Alert Warning method
·

Buzzer

·

Steering Vibration


Sensitivity Timing of the lane departure alert
·

High

·

Standard


Sway Warning Select to enable/disable the vehicle sway warning function
·

ON

·

OFF


Sway Sensitivity Timing of the vehicle sway warning function
·

High

·

Standard

·

Low





DIAGNOSIS


a.

In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The DTCs of malfunctioning parts can be read by connecting the Global TechStream (GTS). Refer to the Repair Manual for details.