FUNCTION OF MAIN COMPONENTS
| Component | Function |
|---|---|
|
*1: Models with parking assist monitor system or panoramic view monitor system *2: Models with parking assist monitor system *3: Models with panoramic view monitor system *4: Models with automatic transmission *5: Models with manual transmission |
|
| Blind Spot Monitor Sensor LH/RH | ·
Outputs radar waves from the blind spot monitor sensor to the blind spot sensor detection area, uses the reflected radar waves for detecting the presence of a vehicle, the vehicle-to-vehicle distance, and the relative speed, and then sends this information to the built-in signal processing circuit. ·
The signal processing circuit determines if a vehicle is present, and illuminates or blinks the outer rear view mirror indicator light accordingly. ·
Receives display dimmer signals from the main body ECU and dims the outer rear view mirror indicator light. |
| Outer Rear View Mirror Assembly LH/RH
·
Outer Rear View Mirror Indicator Light |
·
Illuminates to inform the driver that a vehicle has been detected in the blind spot monitor sensor detection area. ·
Flashes to inform the driver when the turn signal switch is operated if a vehicle has been detected in the blind spot monitor sensor detection area. ·
Both indicator lights flash to inform the driver that a vehicle has been detected in the blind spot detection area while the driver is reversing. |
| RCTA Buzzer (Blind Spot Monitor Buzzer) | Sounds when a vehicle is detected in the blind spot monitor sensor detection area while the driver is reversing. |
| Combination Meter Assembly
·
BSM Indicator ·
RCTA OFF Indicator ·
Multi-information Display ·
Meter Buzzer |
·
Sends the turn light signal to the blind spot monitor sensor LH. ·
Sends the on/off signal of the BSM function and RCTA function to the blind spot monitor sensor LH. ·
Sends the customization information signal of the BSM function and RCTA function to the blind spot monitor sensor LH. ·
Illuminates the BSM indicator to inform the driver when the BSM function is on. ·
Illuminates the RCTA OFF indicator to inform the driver when the RCTA function is off. ·
When a malfunction is detected in the blind spot monitor system or the blind spot monitor system determine that control is not possible, the RCTA OFF indicator blinks, meter buzzer sounds and a message is displayed on the multi-information display to warn the driver. |
| Radio and Display Receiver Assembly*1 | Receives visual signals from the rear television camera assembly, and displays them. |
| Rear Television Camera Assembly*2 | The RCTA icon is superimposed on the captured image. Then, the image is sent to the radio and display receiver assembly. |
| Parking Assist ECU*3 | |
| Steering Sensor | ·
Sends the steering angle signal to the blind spot monitor sensor LH. ·
Sends the turn light signal to the combination meter assembly. |
| Turn Signal Switch | Sends the turn light signal to the steering sensor. |
| Airbag ECU (Airbag Sensor Assembly)
·
Yawrate Sensor |
Sends yawrate information to the blind spot monitor sensor LH. |
| ECM | Sends the shift position signal to the blind spot monitor sensor LH.*4 |
| Back-up Light Switch Assembly*5 | Sends the on/off signals of the back-up light switch assembly to the blind spot monitor sensor RH. |
| Skid Control ECU | Sends the vehicle speed signal to the blind spot monitor sensor LH. |
| Main Body ECU (Multiplex Network Body ECU) | Sends display dimmer signals to the blind spot monitor sensor LH. |
| Central Gateway ECU (Network Gateway ECU) | Relays the signal between the CAN communication buses. |
| DLC3 | ·
The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions. ·
The Global TechStream (GTS) can be connected to change settings as desired by the user. |
OPERATING CONDITION
The BSM function operates when all of the following conditions are met:
The BSM function is on.
The shift position is other than R.
The vehicle speed is greater than approximately 16 km/h (10 mph).
The RCTA function operates when all of the following conditions are met:
The RCTA function is on.
The shift position is R.
The speed of this vehicle is less than approximately 8 km/h (5 mph).
The speed of the target vehicle is between approximately 8 km/h (5 mph) and 28 km/h (18 mph).
SYSTEM CONTROL
BSM Function
The BSM function can detect vehicles in its detection areas.
The detection areas formed by the blind spot monitor sensor LH and RH are as shown below.
| *a | Approximately 3.0 m (9.84 ft.) | *b | Approximately 3.0 m (9.84 ft.) |
| *c | Approximately 1.0 m (3.28 ft.) | *d | Approximately 0.5 m (1.64 ft.) |
|
Detection Area | - | - |
When this vehicle is overtaken by another vehicle in an adjacent lane.
| *a | This Vehicle | - | - |
|
Vehicle Speed (Fast) |
|
Vehicle Speed (Slow) |
|
Detection Area | - | - |
When another vehicle enters the detection area of this vehicle due to a lane change.
| *a | Another vehicle enters the detection area during lane change (merge in) (Type 1). | *b | Another vehicle enters the detection area during lane change (merge in) (Type 2). |
| *c | This Vehicle | - | - |
|
Motion Direction of This Vehicle |
|
Motion Direction of Another Vehicle |
|
Detection Area | - | - |
According to operation conditions, the BSM function promotes safety confirmation by using the outer rear view mirror indicator light to inform the driver that the system detects vehicles that are in the vehicle's blind spot.
The outer rear view mirror indicator light illuminates when a vehicle is in the vehicle's blind spot and the turn signal switch is not operated. The indicator light flashes when a vehicle is in the vehicle's blind spot and the turn signal switch is operated.
RCTA Function
The RCTA function can detect vehicles in its detection areas.
The system continuously measures the relative speed of an approaching vehicle and its distance. If it is determined that the approaching vehicle will cross the path of this vehicle, the Estimated Crossing Time (ECT) is calculated. When the ECT is 2.5 seconds or less, the system alerts the driver by flashing the outer rear view mirror indicator lights and sounding the RCTA buzzer.
| *a | This Vehicle | *b | Target Vehicle (Approximately 8 km/h (5 mph)) |
| *c | Target Vehicle (Approximately 28 km/h (18 mph)) | *d | Approximately 5.5 m (18.0 ft.) |
| *e | Approximately 20 m (66 ft.) | *f | Target Detection Line |
|
Detection Area | - | - |
Normal Parking
| *a | This Vehicle | *b | Target Vehicle |
|
Detection Area | - | - |
According to operation conditions, the RCTA function promotes safety confirmation by using the outer rear view mirror indicator lights and RCTA buzzer to inform the driver that another vehicle has entered the blind spot monitor sensor alert area of this vehicle.
FUNCTION
Blind Spot Monitor System Operation
The combination meter assembly customization setting can be used to turn BSM function and RCTA function on and off.
It is not possible to enable the RCTA function only.
A BSM indicator is located in the combination meter assembly to make it possible to check that BSM function is on.
A RCTA OFF indicator is located in the combination meter assembly to make it possible to check that RCTA function is off.
The combination meter assembly customization setting can be used to change the brightness of the outer rear view mirror indicator light and volume of the RCTA buzzer.
Customization Function
Settings of some functions can be changed as desired by the user. Refer to the Repair Manual for details.
DIAGNOSIS
In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The DTCs of malfunctioning parts can be read by connecting the Global TechStream (GTS). Refer to the Repair Manual for details.