Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › 2019.06–2021.07
NM35X0E _58 Vehicle Interior _078345 PRE-COLLISION _0379917 PRE-COLLISION SYSTEM GE GENERAL F

PRE-COLLISION  PRE-COLLISION SYSTEM  GENERAL  GENERAL  


OUTLINE


a.

Toyota Safety Sense

i.

The preventive safety package "Toyota Safety Sense" is used to support safe driving.


ii.

Systems that are included in "Toyota Safety Sense" are as follows:

*1: Models with road sign assist system

*2: Models with dynamic radar cruise control system

Toyota Safety Sense
·

Pre-collision System (PCS)

·

Lane Departure Alert (LDA) System

·

Road Sign Assist (RSA) System*1

·

Automatic High Beam (AHB)

·

Dynamic radar cruise control*2





b.

Pre-collision System (PCS)

i.

The pre-collision system uses a millimeter wave radar sensor assembly and forward recognition camera to detect objects in front of the vehicle. When the system determines that the possibility of a frontal collision with an object is high, a warning operates to urge the driver to take evasive action and the potential brake pressure is increased to help the driver avoid the collision. If the system determines that the possibility of a frontal collision with an object is extremely high, the brakes are automatically applied to help avoid the collision or help reduce the impact of the collision.

HINT:

The pre-collision system can be disabled/enabled and the warning timing can be changed.


Detectable objects
Regions Detectable objects Countries/areas
A
·

Vehicles

·

Bicyclists

·

Pedestrians


·

Russia

·

Australia

·

New Zealand

·

Singapore

·

Brunei

·

G.C.C countries

·

South Africa


B
·

Vehicles

·

Pedestrians


·

Taiwan


C
·

Vehicles


·

Indonesia

·

Thailand

·

Philippines

·

Vietnam

·

Myanmar

·

Laos

·

Lebanon

·

Argentina

·

Guatemala

·

Costa Rica

·

Jamaica

·

Chile

·

Nicaragua

·

Panama

·

Peru

·

Bolivia

·

Honduras






PRECAUTION


a.

Ignition Switch Expressions

i.

The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.

Expression Ignition Switch
(Position)
Engine Switch
(Condition)
Ignition Switch off LOCK Off (LOCK)
Ignition Switch ACC ACC On (ACC)
Ignition Switch ON ON On (IG)
Engine Start START On (Start)



b.

Toyota Safety Sense

i.

Toyota Safety Sense is designed to operate under the assumption that the driver will drive safely, and is designed to help reduce the impact to the occupants and the vehicle in the case of a collision or assist the driver in normal driving conditions.


ii.

As there is a limit to the degree of recognition accuracy and control performance that this system can provide, do not overly rely on this system. The driver is always responsible for paying attention to the vehicle's surroundings and driving safely.



c.

To avoid malfunction of the millimeter wave radar sensor assembly

i.

Observe the following precautions. Otherwise, the millimeter wave radar sensor assembly may not operate properly, possibly leading to an accident resulting in death or serious injury.

·

Keep the millimeter wave radar sensor assembly and radar sensor cover clean at all times.

Y240882C01
0.49,1.802 1.156,1.875 true 1.729,1.969 2.698,1.521 true 0.281,1.719 0.708,2.052 0.427,0.333 10 false *1 2.708,1.427 3.135,1.76 0.427,0.333 10 false *2
*1 Radar Sensor Cover *2 Millimeter Wave Radar Sensor Assembly


-

If the front of the millimeter wave radar sensor assembly or the front or back of the radar sensor cover is dirty or covered with water droplets, snow, etc., clean it.

-

Clean the millimeter wave radar sensor assembly and radar sensor cover with a soft cloth to avoid damaging them.


·

Do not attach accessories, stickers (including transparent stickers) or other items to the millimeter wave radar sensor assembly, radar sensor cover or surrounding area.

·

Do not subject the millimeter wave radar sensor assembly or its surrounding area to a strong impact.

·

Do not disassemble the millimeter wave radar sensor assembly.

·

Do not modify or paint the millimeter wave radar sensor assembly or radar sensor cover.

·

The millimeter wave radar sensor assembly complies with relevant radio wave regulations, as shown by the label attached to the millimeter wave radar sensor assembly. Do not remove the label. Additionally, disassembly or modification of the millimeter wave radar sensor assembly may be prohibited by law.

·

Do not erase the letters printed on the millimeter wave radar sensor assembly.




d.

To avoid malfunction of the forward recognition camera

i.

Observe the following precautions. Otherwise, the forward recognition camera may not operate properly, possibly leading to an accident resulting in death or serious injury.

·

Keep the windshield clean at all times.

-

If the windshield is dirty or covered with an oily film, water droplets, snow, etc., clean the windshield.

-

If a glass coating agent is applied to the windshield, it will still be necessary to use the windshield wipers to remove water droplets, etc. from the area of the windshield in front of the forward recognition camera.


·

Do not attach objects, such as stickers, transparent stickers, etc., to the outer side of the windshield in front of the forward recognition camera (shaded area in the illustration).

Y240883C01
3.521,1.188 3.729,1.396 0.208,0.208 10 true *b 3.417,0.635 3.625,0.844 0.208,0.208 10 true *a
*a From the top of the windshield to approximately 10 mm (0.394 in.) below the bottom of the front camera. *b Approximately 200 mm (7.87 in.) (Approximately 100 mm (3.94 in.) to the right and left from the center of the front camera).


·

If the part of the windshield in front of the forward recognition camera is fogged up or covered with condensation or ice, use the windshield defogger to remove the fog, condensation or ice.

·

If water droplets cannot be properly removed from the area of the windshield in front of the forward recognition camera by the windshield wipers, replace the wiper insert or wiper blade.

·

Do not attach window tinting to the windshield.

·

Replace the windshield if it is damaged or cracked.

·

Do not allow liquids to contact the forward recognition camera.

·

Do not allow bright lights to shine into the forward recognition camera.

·

Do not dirty or damage the forward recognition camera.

-

When cleaning the inside of the windshield, do not allow glass cleaner to contact the lens of the front camera. Also, do not touch the lens.


·

Do not subject the forward recognition camera to a strong impact.

·

Do not change the installation position or direction of the forward recognition camera or remove it.

·

Do not disassemble the forward recognition camera.

·

Do not modify any components of the vehicle around the forward recognition camera (inner rear view mirror assembly, visor assembly, etc.) or ceiling.

·

Do not attach any accessories to the hood, front grille or front bumper that may obstruct the forward recognition camera.

·

If a surfboard or other long object is to be mounted on the roof, make sure that it will not obstruct the forward recognition camera.

·

Do not modify the headlights or other lights.

·

Do not install an electronic device or device that emits strong electric waves near the forward recognition camera.




e.

Limitations of the pre-collision system

i.

The driver is solely responsible for safe driving. Always drive safely, taking care to observe your surroundings. Do not use the pre-collision system instead of normal braking operations under any circumstances. This system will not prevent collisions or lessen collision damage or injury in every situation. Do not overly rely on this system. Failure to do so may lead to an accident, resulting in death or serious injury.


ii.

Although this system is designed to help avoid a collision or help reduce the impact of the collision, its effectiveness may change according to various conditions, therefore the system may not always be able to achieve the same level of performance. Do not overly rely on this system and always drive carefully.


iii.

Do not attempt to test the operation of the pre-collision system yourself. Depending on the objects used for testing (dummies, cardboard objects imitating detectable objects, etc.), the system may not operate properly, possibly leading to an accident.



f.

Pre-collision braking

i.

When the pre-collision braking function is operating, a large amount of braking force will be applied.


ii.

If the vehicle is stopped by the operation of the pre-collision braking function, the pre-collision braking function operation will be canceled after approximately 2 seconds. Depress the brake pedal as necessary.


iii.

The pre-collision braking function may not operate if certain operations are performed by the driver. If the accelerator pedal is being depressed strongly or the steering wheel is being turned, the system may determine that the driver is taking evasive action and possibly prevent the pre-collision braking function from operating.


iv.

In some situations, while the pre-collision braking function is operating, operation of the function may be canceled if the accelerator pedal is depressed strongly or the steering wheel is turned and the system determines that the driver is taking evasive action.


v.

If the brake pedal is being depressed, the system may determine that the driver is taking evasive action and possibly delay the operation timing of the pre-collision braking function.



g.

When to disable the pre-collision system

i.

In the following situations, disable the system, as it may not operate properly, possibly leading to an accident resulting in death or serious injury:

·

When the vehicle is being towed

·

When your vehicle is towing another vehicle

·

When transporting the vehicle via truck, boat, train or similar means of transportation

·

When the vehicle is raised on a lift with the engine running and the tires are allowed to rotate freely

·

When inspecting the vehicle using a drum tester such as a chassis dynamometer or speedometer tester, or when using an on-vehicle wheel balancer

·

When a strong impact is applied to the front bumper or front grille, due to an accident or other reasons

·

If the vehicle cannot be driven in a stable manner, such as when the vehicle has been in an accident or is malfunctioning

·

When the vehicle is driven in a sporty manner or off-road

·

When the tires are not properly inflated

·

When the tires are very worn

·

When tires of a size other than specified are installed

·

When tire chains are installed

·

When a compact spare tire or an emergency tire puncture repair kit is used

·

If equipment (snow plow, etc.) that may obstruct the millimeter wave radar sensor assembly or forward recognition camera is temporarily installed to the vehicle