FUNCTION OF MAIN COMPONENTS
| Item | Function | |
|---|---|---|
|
*1: Depending on the region in which the vehicle was sold, the pedestrian detection function and Bicyclists detection function may not be available. *2: Models with automatic transmission *3: Models with manual transmission |
||
| Forward Recognition Camera | ·
Acquires information about a preceding vehicle, pedestrian*1 or Bicyclists*1. ·
Operates the camera heater to remove condensation from the part of the windshield in front of the forward recognition camera. ·
Determines whether a collision is imminent based on the information received from each sensors. Sends control signals to the skid control ECU and ECM when it determines that there is a possibility of a collision or a collision is imminent based on the information received from each sensors. |
|
| Camera Heater (Forward Recognition Hood with Heater Sub-assembly) | Heats the sheet heater in accordance with the signals from the forward recognition camera. | |
| Millimeter Wave Radar Sensor Assembly | Radiates millimeter waves forward, uses the reflected millimeter waves for detecting the presence of a vehicle ahead, the vehicle-to-vehicle distance, and the relative speed, and then sends this information to the forward recognition camera. | |
| Airbag ECU (Airbag Sensor Assembly) | Yawrate Sensor | Detects the yaw rate and lateral/longitudinal deceleration of the vehicle and sends the signal to the forward recognition camera. |
| Steering Sensor | Detects the steering direction and angle of the steering wheel and sends the signal to the forward recognition camera. | |
| VSC OFF Switch | Disables the pre-collision braking and pre-collision brake assist operation when the switch is turned on. The PCS warning light illuminates to show that the pre-collision braking and pre-collision brake assist operation is disabled. The pre-collision warning function can still operate. | |
| Stop Light Switch Assembly | Detects the depressing of the brake pedal and sends a signal to the skid control ECU. | |
| Brake Actuator Assembly | Brake Actuator | ·
Actuates the brakes in accordance with the signals from the skid control ECU. ·
Detects the master cylinder pressure and sends a signal to the skid control ECU. ·
Detects the wheel cylinder pressure and sends a signal to the skid control ECU. |
| Skid Control ECU | ·
Receives a brake assist standby request signal from the forward recognition camera, and switches the brake assist to standby mode. When a master cylinder pressure signal is input, it activates the brake assist. ·
Receives a pre-collision brake request signal from the forward recognition camera, and then applies the brakes. ·
Sends vehicle speed signals to the forward recognition camera. |
|
| Combination Meter Assembly | PCS Warning Light | ·
Illuminates to warn the driver in accordance with signals from the forward recognition camera. ·
Illuminates when the pre-collision system is malfunctioning. ·
Illuminates when the pre-collision system is not available due to when the pre-collision system is turned OFF or pre-collision braking and pre-collision brake assist operation are disabled using the VSC OFF switch. |
| VSC OFF Indicator Light | Illuminates when in VSC OFF mode. | |
| Multi-information Display | ·
Displays a warning message to inform or warn the driver of the system condition in accordance with signals from the forward recognition camera. ·
Displays the pre-collision system setting screen. |
|
| Buzzer | Sounds to warn the driver in accordance with signals from the forward recognition camera. | |
| ECM | ·
Sends accelerator pedal position signal and shift position signal to the forward recognition camera.*2 ·
Sends accelerator pedal position signal and reverse position signal (back-up light switch assembly signal) to the forward recognition camera.*3 ·
Controls engine output based on the signal from the forward recognition camera. |
|
| Air Conditioning Amplifier Assembly | Sends ambient temperature signals to the forward recognition camera. | |
| Main Body ECU (Multiplex Network Body ECU) | Outputs the specification signal of the vehicle to the forward recognition camera. | |
| Central Gateway ECU (Network Gateway ECU) | Relays the signal between the CAN communication buses. | |
| DLC3 | The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions. | |
OPERATING CONDITION
The pre-collision system is enabled and the system determines that the possibility of a frontal collision with a detected object is high. Each function is operational at the following speed:
Pre-collision Warning
| Detectable Objects | Vehicle Speed | Relative Speed between Your Vehicle and Object |
|---|---|---|
| Vehicles | Approximately 10 km/h to 180 km/h
(7 mph to 110 mph) |
← |
| Pedestrians and Bicyclists* | Approximately 10 km/h to 80 km/h
(7 mph to 50 mph) |
← |
Pre-collision Brake Assist
| Detectable Objects | Vehicle Speed | Relative Speed between Your Vehicle and Object |
|---|---|---|
| Vehicles | Approximately 30 km/h to 180 km/h
(20 mph to 110 mph) |
← |
| Pedestrians and Bicyclists* | Approximately 30 km/h to 80 km/h
(20 mph to 50 mph) |
← |
Pre-collision Braking
| Detectable Objects | Vehicle Speed | Relative Speed between Your Vehicle and Object |
|---|---|---|
| Vehicles | Approximately 10 km/h to 180 km/h
(7 mph to 110 mph) |
← |
| Pedestrians and Bicyclists* | Approximately 10 km/h to 80 km/h
(7 mph to 50 mph) |
← |
*: Depending on the region in which the vehicle was sold, the pedestrian detection function and/or Bicyclists detection function may not be available.
The system may not operate in the following situations:
·
If an auxiliary battery terminal has been disconnected and reconnected and then the vehicle has not been driven for a certain amount of time ·
If the shift position is R ·
When the VSC OFF indicator is illuminated (only the pre-collision warning function will be operational). |
SYSTEM CONTROL
The forward recognition camera performs pre-collision system control based on signals from ECUs, sensors and switches.
| Control | Function |
|---|---|
| Pre-collision Warning | When the system determines that the possibility of a frontal collision is high, a buzzer will sound and a warning message will be displayed on the multi-information display to urge the driver to take evasive action. |
| Pre-collision Brake Assist | When the system determines that the possibility of a frontal collision is high, the system applies greater braking force in relation to how strongly the brake pedal is depressed. |
| Pre-collision Braking | If the system determines that the possibility of a frontal collision is extremely high, the brakes are automatically applied to help avoid the collision or reduce the impact of the collision. |
The pre-collision system uses a millimeter wave radar sensor assembly and forward recognition camera to detect objects in front of your vehicle.
The millimeter wave radar sensor assembly excels at detecting the position and speed of target objects, which allows for high-precision detection of long-distance objects and stable operation at night or in bad weather.
The forward recognition camera has superior object shape and size identification performance. However, performance deterioration can easily occur when visibility is poor. In that case, only objects inside the area illuminated by the headlights can be detected at night.
The pre-collision system inputs detection information from both the millimeter wave radar sensor assembly and forward recognition camera to ensure high recognition performance and reliability.
When there is a possibility of a collision, the pre-collision system displays messages on the multi-information display, sounds an alert using the buzzer and performs pre-collision brake assist during brake pedal operations. Also, when there is a high possibility of a collision, the system performs pre-collision braking, contributing to collision avoidance support and collision damage reduction.
When the pre-collision system performs brake control, the skid control ECU illuminates the stop lights to inform drivers behind the vehicle of brake operations.
| *1 | Forward Recognition Camera | *2 | Millimeter Wave Radar Sensor Assembly |
| *3 | Brake Actuator Assembly
·
Skid Control ECU |
- | - |
| *a | Collision Imminent | *b | Vehicle Ahead |
| *c | Own Vehicle | - | - |
|
Forward Recognition Camera Detection Area |
|
Millimeter Wave Radar Sensor Assembly Detection Area |
Object detection function
The system detects objects based on their size, profile, motion, etc. However, an object may not be detected depending on the surrounding brightness and the motion, posture, and angle of the detected object, preventing the system from operating properly. The illustration shows an image of detectable objects.
Region A
Region B
Region C
Cancelation of the pre-collision braking
If either of the following occur while the pre-collision braking function is operating, it will be canceled:
·
The accelerator pedal is depressed strongly. ·
The steering wheel is turned sharply or abruptly. |
Conditions under which the system may operate even if there is no possibility of a collision.
In some situations such as the following, the system may determine that there is a possibility of a frontal collision and operate.
When passing a detectable object, etc.
When changing lanes while overtaking a detectable object, etc.
When approaching a detectable object in an adjacent lane or on the roadside, such as when changing the course of travel or driving on a winding road.
When rapidly closing on a detectable object, etc.
When approaching objects on the roadside, such as detectable objects, guardrails, utility poles, trees, or walls.
When there is a detectable object or other object by the roadside at the entrance of a curve.
When there are patterns or paint in front of your vehicle that may be mistaken for a detectable object.
When the front of your vehicle is hit by water, snow, dust, etc.
When overtaking a detectable object that is changing lanes or making a right/left turn.
When passing a detectable object in an oncoming lane that is stopped to make a right/left turn.
When a detectable object approaches very close and then stops before entering the path of your vehicle.
If the front of your vehicle is raised or lowered, such as when on an uneven or undulating road surface.
When driving on a road surrounded by a structure, such as in a tunnel or on an iron bridge.
When there is a metal object (manhole cover, steel plate, etc.), steps, or a protrusion in front of your vehicle.
When passing under an object (road sign, billboard, etc.).
When approaching an electric toll gate barrier, parking area barrier, or other barrier that opens and closes.
When using an automatic car wash.
When driving through or under objects that may contact your vehicle, such as thick grass, tree branches, or a banner.
When driving through steam or smoke.
When driving near an object that reflects radio waves, such as a large truck or guardrail.
When driving near a TV tower, broadcasting station, electric power plant, or other location where strong radio waves or electrical noise may be present.
Situations in which the system may not operate properly
In some situations such as the following, an object may not be detected by the radar sensor and front camera, preventing the system from operating properly:
When a detectable object is approaching your vehicle.
When your vehicle or a detectable object is wobbling.
If a detectable object makes an abrupt maneuver (such as sudden swerving, acceleration or deceleration).
When your vehicle approaches a detectable object rapidly.
When a detectable object is not directly in front of your vehicle.
When a detectable object is near a wall, fence, guardrail, manhole cover, vehicle, steel plate on the road, etc.
When a detectable object is under a structure.
When part of a detectable object is hidden by an object, such as large baggage, an umbrella, or guardrail.
When multiple detectable objects are close together.
If the sun or other light is shining directly on a detectable object.
When a detectable object is a shade of white and looks extremely bright.
When a detectable object appears to be nearly the same color or brightness as its surroundings.
If a detectable object cuts or suddenly emerges in front of your vehicle.
When the front of your vehicle is hit by water, snow, dust, etc.
When a very bright light ahead, such as the sun or the headlights of oncoming traffic, shines directly into the front camera.
When approaching the side or front of a vehicle ahead.
If a vehicle ahead is a bicycle* or motorcycle.
If a vehicle ahead is narrow, such as a personal mobility vehicle.
If a preceding vehicle has a small rear end, such as an unloaded truck.
If a preceding vehicle has a low rear end, such as a low bed trailer.
If a vehicle ahead has extremely high ground clearance.
If a vehicle ahead is carrying a load which protrudes past its rear bumper.
If a vehicle ahead is irregularly shaped, such as a tractor or side car.
If a vehicle ahead is a child sized bicycle, a bicycle that is carrying a large load, a bicycle ridden by more than one person, or a uniquely shaped bicycle (bicycle with a child seat, tandem bicycle, etc.).*
If a pedestrian/or the riding height of a bicyclist ahead is shorter than approximately 1 m (3.2 ft.) or taller than approximately 2 m (6.5 ft.).*
If a pedestrian/bicyclist is wearing oversized clothing (a rain coat, long skirt, etc.), making their silhouette obscure.*
If a pedestrian is bending forward or squatting or bicyclist is bending forward.*
If a pedestrian/bicyclist is moving fast.*
If a pedestrian is pushing a stroller, wheelchair, bicycle or other vehicle.*
When driving in inclement weather such as heavy rain, fog, snow or a sandstorm.
When driving through steam or smoke.
When the surrounding area is dim, such as at dawn or dusk, or while at night or in a tunnel, making a detectable object appear to be nearly the same color as its surroundings.
When driving in a place where the surrounding brightness changes suddenly, such as at the entrance or exit of a tunnel.
After the engine has started the vehicle has not been driven for a certain amount of time.
While making a left/right turn and for a few seconds after making a left/right turn.
While driving on a curve and for a few seconds after driving on a curve.
If your vehicle is skidding.
If the front of the vehicle is raised or lowered.
If the wheels are misaligned.
If a wiper blade is blocking the front camera.
The vehicle is being driven at extremely high speeds.
When driving on a hill.
If the radar sensor or front camera is misaligned.
*: Depending on the region in which the vehicle was sold, the pedestrian detection function and/or Bicyclists detection function may not be available.
In some situations such as the following, sufficient braking force may not be obtained, preventing the system from performing properly:
If the braking functions cannot operate to their full extent, such as when the brake parts are extremely cold, extremely hot, or wet.
If the vehicle is not properly maintained (brakes or tires are excessively worn, improper tire inflation pressure, etc.).
When the vehicle is being driven on a gravel road or other slippery surface.
Pre-collision Brake Assist
While the pre-collision system has determined that there is a high possibility of a collision, brake hydraulic pressure assistance is performed when the driver depresses the brake pedal. Also, the amount of brake hydraulic pressure assistance increases further when the system determines that there is an even higher possibility of a collision.
Pre-collision Braking
When the pre-collision system detects an object such as a vehicle or road structure in front of the vehicle and determines that the possibility of a collision is high, the system displays a warning message on the multi-information display, and sounds the buzzer to warn the driver.
When the pre-collision system determines that there is a high possibility of a collision, the system performs pre-collision braking control.
If VSC is disabled:
If VSC is disabled, the pre-collision brake assist and pre-collision braking functions are also disabled.
The PCS warning light will turn on and "VSC Turned Off Pre-Collision Brake System Unavailable" will be displayed on the multi-information display.
FUNCTION
The pre-collision system is equipped with a function that can change the following settings.
·
Pre-collision system on (activates) or off (does not activate) setting ·
Warning timing (Early, Middle or Late) setting |
Setting Pre-collision System On (Activates) or Off (does Not Activate)
The on (activates) or off (does not activate) setting for the pre-collision system can be selected on the multi-information display setting screen.
When the pre-collision system is set to off, the PCS warning light illuminates. At that time, the multi-information display shows that the pre-collision system is off.
| *1 | Combination Meter Assembly | *2 | Steering Pad Switch Assembly |
| *a | Multi-information Display | *b | PCS Warning Light |
The system is automatically enabled each time the ignition switch is turned to ON.
Warning Timing Changing
The warning timing of the pre-collision system can be switched on the multi-information display setting screen.
| *1 | Combination Meter Assembly | *2 | Steering Pad Switch Assembly |
| *a | Early | *b | Middle (This is the default setting.) |
| *c | Late | - | - |
The pre-collision system is set to Middle by default.
When Early is selected, the pre-collision system is set to perform a warning operation when there is a long distance between the vehicle and the target object it may collide with (at a timing earlier than Middle).
When Late is selected, the pre-collision system is set to perform a warning operation when there is a short distance between the vehicle and the target object it may collide with (at a timing later than Middle).
DIAGNOSIS
In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The DTCs of malfunctioning parts can be read by connecting the Global TechStream (GTS). Refer to the Repair Manual for details.