FUNCTION OF MAIN COMPONENTS
The main components in the theft deterrent system have the following functions:
| Component | Outline | |
|---|---|---|
|
*1: Except wagon models *2: Wagon models *3: Models with wireless door lock control system or entry and start system *4: Models without wireless door lock control system or entry and start system *5: 5-door models *6: Models with power slide door system |
||
| No. 1 Engine Room Relay Block | Security Warning Relay (S-HORN) | Inputs sounding request signals from the main body ECU and operates the security horn assembly. |
| Horn Relay Assembly (HORN) | Inputs sounding request signals from the main body ECU and operates the high pitched horn assembly and low pitched horn assembly. | |
| High Pitched Horn Assembly | Sounds when attempted break-in or theft is detected. | |
| Low Pitched Horn Assembly | Sounds when attempted break-in or theft is detected. | |
| Security Horn Assembly*1 | Sounds when attempted break-in or theft is detected. | |
| Theft Warning Siren Assembly*2 | Sounds when attempted break-in or theft is detected. | |
| Door Control Receiver*3 | ·
Receives a lock or unlock signal from the transmitter and sends this information to the main body ECU*1 or certification ECU*2. ·
Receives the ID code from the electrical key in the actuation area and transmits it to the certification ECU.*2 |
|
| Instrument Panel Junction Block Assembly | D DR UNLOCK Relay | Inputs driver door unlock request signals from the main body ECU and operates the driver door lock motor. |
| L/D DR UNLOCK Relay | Inputs passenger door unlock request signals from the main body ECU and operates the door lock motors at the front passenger door, rear slide doors and back door. | |
| ALL DR LOCK Relay | Inputs door lock request signals from the main body ECU and operates the door lock motor of all doors. | |
| Front Door Lock with Motor Assembly (for Driver Door)
·
Door Lock Motor ·
Door Lock Position Switch ·
Door Lock Control Switch |
·
Rotates the built-in door lock motor to lock and unlock the doors. ·
Uses the built-in door lock position switch to detect whether the doors are locked or unlocked and outputs the result to the main body ECU. ·
Detects the condition of the built-in door lock control switch and outputs mechanical key lock/unlock request signals to the main body ECU. |
|
| Front Door Lock with Motor Assembly (for Front Passenger Door)
·
Door Lock Motor ·
Door Lock Position Switch ·
Door Lock Control Switch*4 |
·
Rotates the built-in door lock motor to lock and unlock the doors. ·
Uses the built-in door lock position switch to detect whether the doors are locked or unlocked and outputs the result to the main body ECU. |
|
| Slide Door Lock Remote Control Assembly (for Driver Side)*5
·
Door Lock Motor ·
Door Lock Position Switch |
·
Rotates the built-in door lock motor to lock and unlock the doors. ·
Uses the built-in door lock position switch to detect whether the doors are locked or unlocked and outputs the result to the main body ECU. |
|
| Slide Door Lock Remote Control Assembly (for Front Passenger Side)
·
Door Lock Motor ·
Door Lock Position Switch |
·
Rotates the built-in door lock motor to lock and unlock the doors. ·
Uses the built-in door lock position switch to detect whether the doors are locked or unlocked and outputs the result to the main body ECU. |
|
| Back Door Remote Control Assembly
·
Door Lock Motor ·
Door Lock Position Switch |
·
Rotates the built-in door lock motor to lock and unlock the doors. ·
Uses the built-in door lock position switch to detect whether the doors are locked or unlocked and outputs the result to the main body ECU. |
|
| Front Door Courtesy Light Switch Assembly (LH) | Outputs open/close signals for the front door LH to the main body ECU. | |
| Front Door Courtesy Light Switch Assembly (RH) | Outputs open/close signals for the front door RH to the main body ECU. | |
| Rear Door Courtesy Light Switch Assembly (for Driver Side)*5 | Outputs open/close signals for the rear door (driver side) to the main body ECU. | |
| Rear Door Courtesy Light Switch Assembly (for Front Passenger Side) | Outputs open/close signals for the rear door (front passenger side) to the main body ECU. | |
| Back Door Lock with Courtesy Light Switch Assembly
·
Courtesy Switch |
Outputs open/close signals for the back door to the main body ECU. | |
| Hood Lock Assembly
·
Engine Hood Courtesy Switch |
Outputs open/close signals for the engine hood to the main body ECU. | |
| Un-lock Warning Switch Assembly*1 | Detects whether or not the ignition key is inserted into the ignition key cylinder and sends this information to the main body ECU. | |
| Main Body ECU (Multiplex Network Body ECU) | ·
Controls the theft deterrent system in accordance with the signal received from the switches, sensors and ECUs. ·
Outputs horn sounding request signals and outputs hazard warning light flash request signals when attempted break-in or theft is detected. |
|
| Certification ECU (Smart Key ECU Assembly)*2 | ·
Controls the entry and start system in accordance with the signals received from the switches and each ECU. ·
Judges and certifies the electrical key. ·
Transmits the door lock/unlock request signals during the entry function. ·
Sends wireless door lock control signals that are input from the door control receiver to the main body ECU. ·
Transmits the immobiliser set/unset request signals. |
|
| Slide Door Motor Unit (for Driver Side)*5, *6
·
Slide Door ECU |
Controls the power slide door system in accordance with the signal received from the switches, sensors and ECUs. | |
| Slide Door Motor Unit (for Front Passenger Side)*6
·
Slide Door ECU |
Controls the power slide door system in accordance with the signal received from the switches, sensors and ECUs. | |
| ECM | Outputs signals such as the engine speed signal to the main body ECU. | |
| Combination Meter Assembly | ·
Informs driver of theft deterrent system status. ·
Flashes the hazard warning lights when attempted break-in or theft is detected. |
|
| Central Gateway ECU (Network Gateway ECU) | Relays the signal between the CAN communication lines. | |
| DLC3 | ·
The Global TechStream (GTS) can be connected to read the Diagnostic Trouble Codes (DTCs) of malfunctions. ·
The Global TechStream (GTS) can be connected to change settings as desired by the user. |
|
FUNCTION
The theft deterrent system has the following functions:
| Function | Operation |
|---|---|
|
*1: Models without entry and start system *2: Models with entry and start system |
|
| Alarm | When the theft deterrent system switches to the alarm state, the warning items are operated and the alarm sounds for approximately 27.5 seconds. |
| Alarm Indicator | When the theft deterrent system switches to the armed preparation state or alarm state, the security indicator light is illuminated to inform the user. This indicator is also the immobiliser indicator, which blinks when the immobiliser is in the set state. |
| Forced Door Lock | The main body ECU transmits a door lock signal to all the doors when all of the following conditions are met:
·
The theft deterrent system is in the alarm state. ·
One of the doors has been unlocked. ·
There is no key inserted in the ignition key cylinder.*1 ·
There is no electrical key in the actuation area.*2 The function stops when one of the following conditions is met: ·
All doors are locked. ·
The warning ends after approximately 27.5 seconds. ·
The ignition key is inserted in the ignition key cylinder.*1 ·
The electrical key is in the actuation area.*2 |
SYSTEM CONTROL
The theft deterrent system can be set by locking the doors using any of the following operations:
| Door Lock Operation | Vehicles Displaying Item "Warning by Horn" on the Global TechStream (GTS) | Vehicles not Displaying Item "Warning by Horn" on the Global TechStream (GTS) |
|---|---|---|
|
○: Available -: Not available *1: Models with entry and start system *2: Models with wireless door lock control system or entry and start system *3: Keyless lock operation is door lock operation without using the electrical key. First, set the lock position (door lock knob) when the door is open, and close the door while pulling the door handle to lock the door. |
||
| Entry lock operation*1 | ○ | ○ |
| Wireless lock operation*2 | ○ | ○ |
| Key linked lock operation | ○ | - |
| Keyless lock operation*3 | ○ | - |
The theft deterrent system can be canceled by unlocking the doors using any of the following operations:
| Door Unlock Operation | Vehicles Displaying Item "Warning by Horn" on the Global TechStream (GTS) | Vehicles not Displaying Item "Warning by Horn" on the Global TechStream (GTS) |
|---|---|---|
|
○: Available -: Not available *1: Models with entry and start system *2: Models with wireless door lock control system or entry and start system |
||
| Entry unlock operation*1 | ○ | ○ |
| Wireless unlock operation*2 | ○ | ○ |
| Key linked unlock operation | ○ | - |
The states of the theft deterrent system are as follows:
| State | Description | Theft Detection |
|---|---|---|
| Disarmed State | The theft deterrent system has not been set by the user. | Not possible |
| Armed Preparation State | This is the preparation state before the theft deterrent system becomes active (enters the armed state) when the system has been set by the user. | Not possible |
| Armed State | The theft deterrent system is active. (Theft can be detected.) | Possible |
| Alarm Sounding State | A theft attempt has been detected and the warning operation activates. | Possible |
The theft deterrent system activates as shown in the diagram above when one of the items in the following chart occurs in order to cause the system to enter the respective state:
The term "all doors" used in this section refers to the driver door, front passenger door, rear doors and back door.
| Condition | Item |
|---|---|
|
*1: Models without entry and start system *2: Models with wireless door lock control system *3: Models with entry and start system *4: Models with power slide door system |
|
| (1) | In disarmed state 1, when the ignition switch is off, the system state is switched if the following condition is met when the key is not in the key cylinder:*1
·
With all doors and the engine hood closed, all doors are locked by key linked power door lock operation. ·
With all doors and the engine hood closed, all doors are locked by wireless operation.*2 ·
With all doors locked and the engine hood closed, the state changes from any of the doors being opened to all doors being closed. |
| In disarmed state 1, when the engine switch is off, the system state is switched if the following condition is met:*3
·
With all doors and the engine hood closed, all doors are locked by key linked power door lock operation. ·
With all doors and the engine hood closed, all doors are locked by wireless operation. ·
With all doors and the engine hood closed, all doors are locked by entry operation. ·
With all doors locked and the engine hood closed, the state changes from any of the doors being opened to all doors being closed. |
|
| (2) | Approximately 30 seconds elapse. |
| (3) | One of the following conditions is met:*1
·
All doors are unlocked by key linked power door lock operation. ·
All doors are unlocked by wireless operation.*2 ·
Any door is unlocked. ·
Any door is opened. ·
Key is in the key cylinder. ·
The ignition switch is turned to ACC or ON. ·
The auxiliary battery is reconnected. |
| One of the following conditions is met:*3
·
All doors are unlocked by key linked power door lock operation. ·
All doors are unlocked by wireless operation. ·
All doors are unlocked by entry operation. ·
Any door is unlocked. ·
Any door is opened. ·
The engine switch is pushed. ·
The engine switch is turned on (ACC) or on (IG). ·
The auxiliary battery is reconnected. |
|
| (4) | One of the following conditions is met:
·
The engine hood is opened when the engine hood is closed. ·
The auxiliary battery is reconnected when the engine hood is opened, any door is opened or any door is unlocked. ·
Any door is opened when all doors are closed. ·
Any door is unlocked when all doors are locked. ·
The power source mode is changed from Off to ON when the key is not in the key cylinder.*1 ·
The power source mode is changed from off to on (IG) without electrical key.*3 ·
When 5 seconds or more have elapsed after the engine switch is pushed, the power source mode is changed from off to on (IG) without pressing the engine switch.*3 |
| (5) | One of the following conditions is met:*1
·
The ignition switch is turned to ON and the engine is running at 550 rpm for more than approximately 2 seconds. ·
All doors are unlocked by key linked power door lock operation. ·
All doors are unlocked by wireless operation.*2 ·
The ignition switch is turned to ACC or ON when the key is not in the key cylinder. |
| One of the following conditions is met:*3
·
The engine switch is turned to on (IG) and the engine is running at 550 rpm for more than approximately 2 seconds. ·
All doors are unlocked by key linked power door lock operation. ·
All doors are unlocked by wireless operation. ·
All doors are unlocked by entry operation. ·
The engine switch is turned on (ACC) or on (IG) within 5 seconds after the engine switch is pushed. |
|
| (6) | After approximately 27.5 seconds, the alarm stops and the system returns to the armed state. |
| (7) | One of the following conditions is met:
·
The open engine hood is closed with all the doors closed. ·
The power slide door reservation lock is operated with the engine hood and all other doors closed.*4 |
| (8) | One of the following conditions is met:*1
·
Any door is unlocked when all doors are locked. ·
Any door is opened. ·
While the power slide door is closing, the power slide door reverses direction, stops partway or any door other than the slide door is opened.*4 ·
Key is in the key cylinder. ·
The ignition switch is turned to ACC or ON. ·
The auxiliary battery is reconnected. ·
All doors are unlocked by key linked power door lock operation. ·
All doors are unlocked by wireless operation.*2 |
| One of the following conditions is met:*3
·
Any door is unlocked when all doors are locked. ·
Any door is opened. ·
While the power slide door is closing, the power slide door reverses direction, stops partway or any door other than the slide door is opened.*4 ·
The engine switch is pushed. ·
The engine switch is turned on (ACC) or on (IG). ·
The auxiliary battery is reconnected. ·
All doors are unlocked by key linked power door lock operation. ·
All doors are unlocked by wireless operation. ·
All doors are unlocked by entry operation. |
|
| (9) | In disarmed state 1, when the ignition switch is off, the system state is switched if the following condition is met when the key is not in the key cylinder:*1
·
With all doors closed and the engine hood opened, all doors are locked by key linked power door lock operation. ·
With all doors closed and the engine hood opened, all doors are locked by wireless operation.*2 ·
With all doors locked and the engine hood opened, the state changes from any of the doors being opened to all doors being closed. ·
While the power slide door is closing and all doors are closed, all doors are locked by wireless operation.*4 |
| In disarmed state 1, when the engine switch is off, the system state is switched if the following condition is met:*3
·
With all doors closed and the engine hood opened, all doors are locked by key linked power door lock operation. ·
With all doors closed and the engine hood opened, all doors are locked by wireless operation. ·
With all doors closed and the engine hood opened, all doors are locked by entry operation. ·
With all doors locked and the engine hood opened, the state changes from any of the doors being opened to all doors being closed. ·
While the power slide door is closing and all doors are closed, all doors are locked by wireless operation.*4 ·
While the power slide door is closing and all doors are closed, all doors are locked by entry operation.*4 |
|
| (10) | The engine hood is opened. |
| Condition | Item |
|---|---|
|
*1: Models without entry and start system *2: Models with entry and start system *3: Models with power slide door system |
|
| (1) | In disarmed state 1, when the ignition switch is off, the system state is switched if the following condition is met when the key is not in the key cylinder:*1
·
With all doors and the engine hood closed, all doors are locked by wireless operation. |
| In disarmed state 1, when the engine switch is off, the system state is switched if the following condition is met:*2
·
With all doors and the engine hood closed, all doors are locked by wireless operation. ·
With all doors and the engine hood closed, all doors are locked by entry operation. |
|
| (2) | Approximately 30 seconds elapse. |
| (3) | One of the following conditions is met:*1
·
All doors are unlocked by wireless operation. ·
Any door is unlocked. ·
Any door is opened. ·
Key is in the key cylinder. ·
The ignition switch is turned to ACC or ON. ·
The auxiliary battery is reconnected. |
| One of the following conditions is met:*2
·
All doors are unlocked by wireless operation. ·
All doors are unlocked by entry operation. ·
Any door is unlocked. ·
Any door is opened. ·
The engine switch is pushed. ·
The engine switch is turned on (ACC) or on (IG). ·
The auxiliary battery is reconnected. |
|
| (4) | One of the following conditions is met:
·
The engine hood is opened when the engine hood is closed. ·
The auxiliary battery is reconnected when the engine hood is opened, any door is opened or any door is unlocked. ·
Any door is opened when all doors are closed. ·
Any door is unlocked when all doors are locked. ·
The power source mode is changed from Off to ON when the key is not in the key cylinder.*1 ·
The power source mode is changed from off to on (IG) without electrical key.*2 ·
When 5 seconds or more have elapsed after the engine switch is pushed, the power source mode is changed from off to on (IG) without pressing the engine switch.*2 ·
The engine hood is opened. ·
Any door is opened. ·
The power source mode is ON when the key is not in the key cylinder. |
| (5) | One of the following conditions is met:*1
·
The ignition switch is turned to ON and the engine is running at 550 rpm for more than approximately 2 seconds. ·
All doors are unlocked by wireless operation. |
| One of the following conditions is met:*2
·
The engine switch is turned to on (IG) and the engine is running at 550 rpm for more than approximately 2 seconds. ·
All doors are unlocked by wireless operation. ·
All doors are unlocked by entry operation. |
|
| (6) | After approximately 27.5 seconds, the alarm stops and approximately 5 seconds later the system returns to the armed state. |
| (7) | One of the following conditions is met:
·
The open engine hood is closed with all the doors closed. ·
The power slide door reservation lock is operated with the engine hood and all other doors closed.*3 |
| (8) | One of the following conditions is met:*1
·
Any door is unlocked when all doors are locked. ·
Any door is opened. ·
While the power slide door is closing, the power slide door reverses direction, stops partway or any door other than the slide door is opened.*3 ·
Key is in the key cylinder. ·
The ignition switch is turned to ACC or ON. ·
The auxiliary battery is reconnected. ·
All doors are unlocked by wireless operation. |
| One of the following conditions is met:*2
·
Any door is unlocked when all doors are locked. ·
Any door is opened. ·
While the power slide door is closing, the power slide door reverses direction, stops partway or any door other than the slide door is opened.*3 ·
The engine switch is pushed. ·
The engine switch is turned on (ACC) or on (IG). ·
The auxiliary battery is reconnected. ·
All doors are unlocked by wireless operation. ·
All doors are unlocked by entry operation. |
|
| (9) | In disarmed state 1, when the ignition switch is off, the system state is switched if the following condition is met when the key is not in the key cylinder:*1
·
With all doors closed and the engine hood opened, all doors are locked by wireless operation. ·
While the power slide door is closing and all doors are closed, all doors are locked by wireless operation.*3 |
| In disarmed state 1, when the engine switch is off, the system state is switched if the following condition is met:*2
·
With all doors closed and the engine hood opened, all doors are locked by wireless operation. ·
With all doors closed and the engine hood opened, all doors are locked by entry operation. ·
While the power slide door is closing and all doors are closed, all doors are locked by wireless operation.*3 ·
While the power slide door is closing and all doors are closed, all doors are locked by entry operation.*3 |
|
| (10) | The engine hood is opened. |