Home › Engine / Hybrid System › 1GD-FTV (EMISSION CONTROL) › EMISSION CONTROL SYSTEM › 2019.06–2021.07
NM35X0E _51 Engine / Hybrid System _080142 1GD-FTV EMISSION CONTROL _0389536 EMISSION CONTROL SYSTEM CO CONTROL F

1GD-FTV EMISSION CONTROL  EMISSION CONTROL SYSTEM  CONTROL  EMISSION CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The main components of the EGR system are as follows:

Component Function

*1: Models with EGR cooler

*2: Models with No. 5 exhaust gas temperature sensor

ECM Controls the emission control system based on signals from each sensor.
Electric EGR Control Valve Assembly Actuated by the ECM, this valve controls the flow rate of EGR gas.
EGR Valve Position Sensor (Built into Electric EGR Control Valve Assembly) Detects the EGR valve position.
Diesel Throttle Valve Actuated by the ECM, this valve controls the flow rate of intake air.
No. 1 EGR Cooler*1 Cools EGR gas.
No. 2 EGR Valve Assembly*1 for Single Actuator EGR Bypass Valve Switches the flow passage of EGR gas in 2 stages.
for Double Actuator EGR Bypass Valve Switches the flow passage of EGR gas in 3 stages.
No. 5 Exhaust Gas Temperature Sensor*2 Detects the exhaust gas temperature.


b.

The main components of the catalyst support control are as follows:

Component Function

*1: Models with Air fuel ratio sensor

*2: Models with No. 1 nitrogen oxides sensor

*3: Models with particulate matter sensor assembly

ECM Controls the emission control system based on signals from each sensor.
Differential Pressure Sensor
·

Monitors the differential pressure before and after the DPF.

·

Compares this data with the PM accumulation amount calculated by the ECM. If there is a large deviation in the comparison result, the ECM corrects the PM accumulation amount.


Exhaust Fuel Addition Injector Assembly Injects fuel into the exhaust manifold.
Exhaust Gas Temperature Sensor Detects the exhaust gas temperature.
No. 2 Exhaust Gas Temperature Sensor
No. 3 Exhaust Gas Temperature Sensor
Air Fuel Ratio Sensor*1 Detects the oxygen concentration in exhaust gas.
No. 1 Nitrogen Oxides Sensor*2 Detects the oxygen concentration in exhaust gas.
Particulate Matter Sensor Assembly*3 Detects the state of DPF.


c.

The main components of the UREA SCR system are as follows:

Component Function

*1: Models with No. 1 nitrogen oxides sensor

*2: Models without No. 1 nitrogen oxides sensor

*3: Models with particulate matter sensor assembly

ECM Receives the signals from the No. 4 Exhaust gas temperature sensor and NOx sensor (nitrogen oxides sensor) and sends the signals to the urea pump control ECU.
Urea Pump Control ECU Controls the UREA SCR system based on signals from each sensor.
No. 4 Exhaust Gas Temperature Sensor Detects the exhaust gas temperature.
No. 1 Nitrogen Oxides Sensor*1
·

Detects the oxygen concentration in exhaust gas.

·

Detects the concentration of NOx in the exhaust gas.


Nitrogen Oxides Sensor*2 Detects the concentration of NOx in the exhaust gas.
No. 2 Nitrogen Oxides Sensor*1
Particulate Matter Sensor Assembly*3 Detects the state of DPF.



FUNCTION


a.

The main function of the emission control system is as follow:

Function Outline

*1: Models with EGR system

*2: Models with catalyst support control

*3: Models with UREA SCR system

EGR Control*1 This system is designed to help reduce and control NOx formation due to a reduction of peak temperature in the engine combustion chamber, which is accomplished by the introduction of an amount of inert gas into the intake manifold.
Catalyst Support Control*2
·

When an extremely large amount of PM is accumulated in the DPF, the back pressure of the engine increases and the PM is combusted at once, potentially damaging the filter. In order to prevent that, it is necessary to forcibly combust the accumulated PM. Therefore, the accumulated PM is combusted by increasing the temperature of the filter.

·

If the temperature of the DPF does not increase and the PM keeps accumulating in the DPF, a message is displayed on the multi-information display to notify the driver.


UREA SCR System*3 Urea solution is injected by the urea injector set to purify NOx in the exhaust gas.