Home › Engine / Hybrid System › IDLING STOP CONTROL › STOP AND START › from 2019.06
NM35X0E _51 Engine / Hybrid System _079581 IDLING STOP CONTROL _0385880 STOP AND START CO CONTROL F

IDLING STOP CONTROL  STOP AND START  CONTROL  IDLING STOP CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function

*1: Models with A/T

*2: Models with M/T

*3: Models with premium package

Engine Stop and Start ECU Sends either an engine stop or restart signal to the ECM according to the signals from each sensor and switch.
Engine Stop and Start ECU Backup Boost Converter
·

Supplies battery voltage to help make up for the voltage drop that occurs when the engine is restarted, preventing the operation of various systems from being interrupted due to low battery voltage.

·

Supplies battery voltage to the oil pump with solenoid assembly.*1


Park/Neutral Position Switch Assembly*1 Detects the shift lever position and sends a signal to the engine stop and start ECU.
Clutch Start Switch Assembly*2 Detects depression of the clutch pedal and transmits a signal to the engine stop and start ECU.
Clutch Switch Assembly*2
Neutral Position Switch*2 Recognizes that the shift lever is in N and sends a signal to the engine stop and start ECU.
Vacuum Sensor Detects the brake booster vacuum pressure and sends a signal to the engine stop and start ECU.
Hood Lock Assembly Engine Hood Courtesy Switch Detects whether the hood is open or closed and sends a signal to the engine stop and start ECU.
Front Door Courtesy Light Switch Assembly (for Driver) Detects whether the driver door is open or closed and sends a signal to the engine stop and start ECU via the main body ECU (multiplex network body ECU) via CAN communication.
Front Seat Inner Belt Assembly (for Driver) Front Seat Belt Buckle Switch (for Driver) Detects whether or not the driver's seat belt has been fastened, and sends a signal to the engine stop and start ECU via the main body ECU (multiplex network body ECU) via CAN communication.
Air Conditioning Amplifier Assembly Sends an outside temperature signal and A/C switch signal to the engine stop and start ECU.
Combination Meter Assembly Stop and Start Indicator Light
·

Turns on when the engine is stopped due to stop and start control.

·

Blinks to inform the driver that the idling stop is canceled and the engine will restart when the driver door is opened with the shift lever in D or S during idling stop.*1

·

If the shift lever is moved out of N without the clutch pedal depressed during idling stop, the buzzer sounds and the stop and start indicator light blinks at the same time.* 2


Stop and Start Cancel Indicator Light
·

Turns on to inform the driver that the system has been disabled when stop and start system operation is prohibited by the stop and start system cancel switch (eco run cancel switch assembly).

·

If a system malfunction is detected, the stop and start cancel indicator light blinks to inform the driver.


Multi-information Display
·

Displays the amount of time idling stop was performed since the ignition switch was turned ON to when the ignition switch was turned off and the amount of time idling stop was performed since the reset switch was last pressed.

·

Displays the settings of the stop and start system or warning information, etc.


Stop and Start System Cancel Switch (Warning Canceling Switch Assembly) Operation of the system can be canceled by pressing the stop and start system cancel switch (eco run cancel switch assembly). Pressing the switch again or turning the power source off and back on restores the operation of the system.
Idle Up Switch Send an idle up switch signal to the engine stop and start ECU.
ECM
·

Sends various information about engine conditions to the engine stop and start ECU.

·

Based on signals from the battery state sensor assembly, determines whether the battery installed on the vehicle is a specified or non-specified battery, and sends the determination result to the engine stop and start ECU.


Skid Control ECU
·

Sends a vehicle speed signal to the engine stop and start ECU.

·

Sends a master cylinder pressure signal to the engine stop and start ECU.


Airbag ECU (Airbag Sensor Assembly) Sends airbag deployment information in the event of a collision and a deceleration signal to the engine stop and start ECU.
Main Body ECU (Multiplex Network Body ECU) Sends a front door courtesy light switch assembly (for driver) signal and front seat belt buckle switch (for driver) signal to the engine stop and start ECU.
Steering Sensor Detects the steering angle and sends signals to the engine stop and start ECU.
External Backup Boost Converter (Eco Run Vehicle Converter Assembly)*3 Supplements the voltage drop when the engine is stopped to stabilize the audio output.
Transmission Valve Body Assembly*1 Oil Pump with Solenoid Assembly Holds the ATF pressure during idle stop.
ATF Temperature Sensor Detects the ATF temperature.
Battery State Sensor Assembly Detects the battery charging and discharging amount and sends a signal to the ECM.
Stop Light Switch Assembly*1 Detects a brake pedal released condition and sends a signal to the engine stop and start ECU via the ECM.
Accelerator Pedal Sensor Assembly*1 Detects an accelerator pedal opening angle and sends a signal to the engine stop and start ECU via the ECM.
Crankshaft Position Sensor Detects the crankshaft angle when the engine is stopped and sends this information to the ECM.
Engine Coolant Temperature Sensor Sends the coolant temperature to the engine stop and start ECU via the ECM.
Generator Assembly Sends the generator assembly generation condition to the engine stop and start ECU via the ECM.


SYSTEM CONTROL


a.

Early Stage Injection Control

i.

Early stage injection control shortens the time it takes the engine to restart after the stop and start system stops the engine, allowing smooth initial acceleration.


ii.

The ECM memorizes the crankshaft angle detected by the crankshaft position sensor when the engine is stopped by the stop and start system.


iii.

The ECM helps shorten engine start-up time by beginning fuel injection at the appropriate cylinder based on the stored crankshaft angle when the engine restarts.

Y177235E05
2.365,1.313 2.365,0.781 false 5.5,0.646 6.969,1.104 1.469,0.458 10 false Injector Assembly 3.802,0.625 4.177,0.896 0.375,0.271 10 false ECM 3.271,1.875 4.719,2.26 1.448,0.385 10 false Crank Position Sensor 0.688,0.427 1.729,1.021 1.042,0.594 10 false Engine Stop and Start ECU 1.615,1.333 3.323,1.583 1.708,0.25 10 false CAN Communication Line



b.

Hill-start Assist Function (Models with A/T)

i.

The driving force (creep phenomenon) of a former A/T vehicle is regulated by depressing the brake pedal while stopped, and the driving force is transmitted by releasing the brake pedal when starting the vehicle. However, when starting a stop and start system equipped vehicle with its engine stopped due to the activation of the idle stop function, there is a short time delay before the driving force is generated as the engine will start after the brake pedal is released.


ii.

The hill-start assist function is a system to assist starting of a stop and start system equipped vehicle on a slope to deal with the situation described above, retaining the brake hydraulic pressure until sufficient driving force is generated.

HINT:
·

The hill-start assist function operates not only on a slope but also on a level surface.

·

Abnormal sounds may be heard, but this does not mean the brake is malfunctioning.

·

The brake pedal response may change or it may vibrate, but this does not mean it is malfunctioning.





c.

System Prohibit Control

i.

For safety, battery protection, comfort and ECU learning reasons, the engine stop and start ECU prohibits stop and start system operation if any one of the following conditions is met.

Prohibition Reason Condition

*: If the value learned by the ECU has been cleared by disconnecting the battery or for another reason, stop and start system operation will be prohibited until ECU learning is complete.

Safety If the engine is started with the hood open, such as when jump starting, engine restart operation cannot be ensured. Therefore, stop and start system operation will be prohibited. The operation of the system will be restored on the next trip.
If the driver door or hood is opened before the engine stops, stop and start system operation will be prohibited for safety reasons.
The brake booster vacuum is insufficient.
The driver seat belt is unfastened before the engine stops.
The engine catalyst is being quickly warmed up.
Battery Protection The refresh charge continues for 0.5 to 1 hour, and is carried out approximately every 30 hours of driving. While the refresh charge is occurring, stop and start system operation will be disabled.
When the idling stop rate becomes higher than the predetermined rate, stop and start system operation will be disabled.
When the battery voltage becomes low and the battery integrated current value becomes the threshold value or less, stop and start operation will be disabled.
Comfort If the air conditioning is on when the outside temperature is high and the evaporator temperature is high, stop and start system operation will be prohibited.
If the air conditioning is on when the outside temperature is low, stop and start system operation will be prohibited.
If the heater is on when the outside temperature is low and the engine coolant temperature is low, stop and start system operation will be prohibited.
If the idle up switch, front DEF switch and blower switch are on, stop and start system operation will be prohibited.
ECU Learning ECU learning is not complete.*
Operation If the vehicle is stopped while the steering wheel is being operated, stop and start system operation will be prohibited.



d.

Warning Control

i.

If any of the following operations are performed while the engine is stopped due to system control, the system will not restart the engine. The driver will be warned by a buzzer, or the engine will be regarded as stalled or will be restarted.

Operation Warning Control
The engine hood is opened The engine stops (mode changes to "stalled", and the engine cannot be restarted until the ignition switch is turned off and then on)
The driver door is opened The engine starts, warning buzzer sounds and stop and start indicator blinks.
The driver seat belt is unfastened The engine starts



e.

Operating Conditions at Engine Stop and Restart (Models with A/T)

i.

The engine may stop if all of these conditions are detected.

Item Operating Condition

*1: Models with Gross Vehicle Mass (GVM) 3.5 t or less

*2: Models with GVM exceeds 3.5 t

*3: When the battery fluid temperature becomes -15°C (5°F) or lower or 75°C (167°F) or higher, control is prohibited. After control is prohibited and the battery fluid temperature rises to -10°C (14°F) or higher or falls to 70°C (158°F) or lower, control is performed.

*4: Regarding Battery Integrated Current

In the stop and start system, the engine stop and start ECU switches the system control mode (stop and start system control permitted/prohibited) based on the battery condition (charge/discharge condition) to protect the battery and to ensure stable engine restarting performance.

The battery charge/discharge condition is determined from the integrated current value calculated from the battery state sensor assembly signal. The integrated current value is obtained by multiplying the current (ampere) detected by the battery state sensor assembly by the time (seconds), and is expressed in the unit A-sec. This can be measured by the Global TechStream (GTS).

The engine stop and start ECU determines the power charge based on the integrated current value and prohibits stop and start system control if the value becomes the threshold or less, because the battery might not be able to start the engine. The threshold varies according to the status of battery charge control.

*5: After the integrated current value becomes -19123 A-sec or less, in order to charge the battery, idling stop control is prohibited until the value becomes -17971 A-sec or more.

*6: After the integrated current value becomes -1152 A-sec or less, in order to charge the battery, idling stop control is prohibited until the value becomes 0 A-sec or more.

*7: When the engine is restarted, ensure proper braking force so that the vehicle does not advance.

Idle Stop Engine Coolant Temperature 15°C to 105°C (59°F to 221°F)
ATF Temperature 25°C to 112°C (77°F to 233.6°F)
Driver Door Closed
Brake Booster Vacuum Sufficient brake booster vacuum
Brake Master Cylinder Fluid Pressure*7 The brake master cylinder fluid pressure is 2.0 MPa (20.4 kg/cm2, 290 psi) or higher. (changes according to gradient.)
Stop and Start Cancel Switch (Eco Run Cancel Switch Assembly) Off condition
Road Gradient -6° to 8°
Vehicle Speed Vehicle speed changes from a constant speed to 0 km/h.
Engine Speed 1200 r/min or less
Shift Lever Position P, D
Drive Mode ECO or NORMAL mode
Driver's Seat Belt 3 seconds or more elapse after the seat belt is fastened.
Engine Hood The engine hood is closed and 3 seconds or more have elapsed.
Battery Voltage 7.92 V or more at engine start.*1
7.9 V or more at engine start.*2
Battery Fluid Temperature -10°C to 70°C (14°F to 158°F)*3
Battery Integrated Current*4 When the integrated current value meets any of the following conditions:
·

-17971 A-sec or more: Status of Battery Charge Control is Charge Control Coordination Mode, Stop and Start Standalone Mode, Temperature High/Low Mode or Low Temperature Mode.*5

·

0 A-sec or more: Status of Battery Charge Control is Stop and Start Restriction Mode.*6


Air Conditioning During "cooling down or warming up" or defrost function is not operating.
ECU Learning Completed
Ambient Temperature -5°C (23°F) or more
Steering Operation Not operated
Atmospheric Pressure Within acceptable range due to elevation, etc.


ii.

The engine will restart if any of these conditions are detected.

Item Operating Condition

*: When the shift lever is in D.

Engine Restart Brake Booster Vacuum Insufficient brake booster vacuum
Brake Master Cylinder Fluid Pressure The brake pedal is released.
Air Conditioning When the air conditioning is on and a timer in the air conditioning amplifier assembly completes.
When the A/C switch is on and the evaporator temperature exceeds the threshold.
Either the A/C switch, blower switch, defroster switch, pollen removal mode switch or idle-up switch is on.
Stop and Start System Cancel Switch (Eco Run Cancel Switch Assembly) The stop and start system cancel switch (eco run cancel switch assembly) is turned on.
Battery
·

The battery voltage is less than 11.4 V.

·

The battery integrated current becomes the threshold value or less.


Driver's Door The driver's door is opened.
Driver's Seat Belt The driver's seat belt is unfastened.
Vehicle Speed A vehicle speed signal is input.
Accelerator Pedal The accelerator pedal is depressed.
Brake Pedal The brake pedal is released.*
Shift Lever Moved from D or S position to another position.
Steering Operation The steering wheel is operated.



f.

Operating Conditions at Engine Stop and Restart (Models with M/T)

i.

The engine may stop if all of these conditions are detected.

Item Operating Condition

*1: When the battery fluid temperature becomes -15°C (5°F) or lower or 75°C (167°F) or higher, control is prohibited. After control is prohibited and the battery fluid temperature rises to -10°C (14°F) or higher or falls to 70°C (158°F) or lower, control is performed.

*2: Regarding Battery Integrated Current

In the stop and start system, the engine stop and start ECU switches the system control mode (stop and start system control permitted/prohibited) based on the battery condition (charge/discharge condition) to protect the battery and to ensure stable engine restarting performance.

The battery charge/discharge condition is determined from the integrated current value calculated from the battery state sensor assembly signal. The integrated current value is obtained by multiplying the current (ampere) detected by the battery state sensor assembly by the time (seconds), and is expressed in the unit A-sec. This can be measured by the Global TechStream (GTS).

The engine stop and start ECU determines the power charge based on the integrated current value and prohibits stop and start system control if the value becomes the threshold or less, because the battery might not be able to start the engine. The threshold varies according to the status of battery charge control.

*3: After the integrated current value becomes -19123 A-sec or less, in order to charge the battery, idling stop control is prohibited until the value becomes -17971 A-sec or more.

*4: After the integrated current value becomes -1152 A-sec or less, in order to charge the battery, idling stop control is prohibited until the value becomes 0 A-sec or more.

Idle Stop Engine Coolant Temperature 15°C to 105°C (59°F to 221°F)
Driver Door Closed
Brake Booster Vacuum Sufficient brake booster vacuum
Stop and Start System Cancel Switch (Eco Run Cancel switch assembly) Off condition
Vehicle Speed Vehicle speed changes from a constant speed to 0 km/h.
Engine Speed 1200 r/min or less
Clutch Pedal Released
Shift Lever Position Neutral
Driver's Seat Belt 3 seconds or more elapse after the seat belt is fastened.
Engine Hood The engine hood is closed and 3 seconds or more have elapsed.
Battery Voltage 7.9 V or more at engine start.
Battery Fluid Temperature -10°C to 70°C (14°F to 158°F)*1
Battery Integrated Current*2 When the integrated current value meets any of the following conditions:
·

-17971 A-sec or more: Status of Battery Charge Control is Charge Control Coordination Mode, Stop and Start Standalone mode, Temperature High/Low Mode or Low Temperature Mode.*3

·

0 A-sec or more: Status of Battery Charge Control is Stop and Start Restriction Mode.*4


Air Conditioning During "cooling down or warming up" or defrost function is not operating.
ECU Learning Completed
Ambient Temperature -5°C (23°F) or more
Steering Operation Not operated
Atmospheric Pressure Within acceptable range due to elevation, etc.


ii.

The engine will restart if any of these conditions are detected.

Item Operating Condition
Engine Restart Brake Booster Vacuum Insufficient brake booster vacuum
Air Conditioning When the air conditioning is on and a timer in the air conditioning amplifier assembly completes.
When the A/C switch is on and the evaporator temperature exceeds the threshold.
Either the A/C switch, blower switch, defroster switch, pollen removal mode switch or idle up switch is on.
Stop and Start System Cancel Switch (Eco Run Cancel Switch Assembly) The stop and start system cancel switch (eco run cancel switch assembly) is turned on.
Battery
·

The battery voltage is less than 11.4 V.

·

The battery integrated current becomes the threshold value or less.


Driver's Door The driver's door is opened.
Driver's Seat Belt The driver's seat belt is unfastened.
Vehicle Speed A vehicle speed signal is input.
Clutch Pedal The clutch pedal is depressed.
Steering Operation The steering wheel is operated.



g.

Stop and Start Priority Control

i.

Stop and start operation time when the air conditioning is operating can be changed between "Standard" and "Extended (the stop and start system has priority)" using the steering pad switch located on the steering pad, enabling the user to select the preferred setting. However, even when selecting "Extended (the stop and start system has priority)", the idling stop time may not change depending on the vehicle condition or the surrounding environment.



h.

Shift Lever Operation and Stop and Start Control in Different Situations (Models with Automatic Transmission)

i.

The stop and start system performs the following controls based on the shift lever operation and situation. Furthermore, the condition of the stop and start system after the shift lever is operated may change depending on the vehicle condition and surrounding environment.

Shift Lever in D while Idling
W143069E01
2.156,0.635 3.583,0.958 1.427,0.323 10 false Shift Lever Operation 5,0.573 6.427,1.125 1.427,0.552 10 false Stop and Start System Condition after Shift Lever Operation 1.938,1.302 2.188,1.51 0.25,0.208 10 false D 2.781,1.302 3.031,1.51 0.25,0.208 10 false N 3.635,1.302 3.885,1.51 0.25,0.208 10 false R 4.458,1.313 4.708,1.521 0.25,0.208 10 false P 1.094,1.302 1.344,1.51 0.25,0.208 10 false S 0.969,3.281 1.448,3.542 0.479,0.26 10 false : Idling 1.823,3.281 2.698,3.573 0.875,0.292 10 false : Idling stop 5.573,1.604 6.01,1.875 0.438,0.271 10 false Idling 5.573,2.01 6.01,2.281 0.438,0.271 10 false Idling 5.583,2.427 6.021,2.698 0.438,0.271 10 false Idling 5.427,2.875 6.167,3.146 0.74,0.271 10 false Idling stop

Shift Lever in D and Current Idling Stop Time Less than 2 Seconds
W143070E01
2.208,0.594 3.552,0.865 1.344,0.271 10 false Shift Lever Operation 5.052,0.531 6.49,1.198 1.438,0.667 10 false Stop and Start System Condition after Shift Lever Operation 1.125,1.25 1.344,1.448 0.219,0.198 10 false S 2.01,1.25 2.229,1.448 0.219,0.198 10 false D 2.844,1.25 3.063,1.448 0.219,0.198 10 false N 3.688,1.25 3.906,1.448 0.219,0.198 10 false R 4.531,1.26 4.75,1.458 0.219,0.198 10 false P 5.583,1.604 6.167,1.854 0.583,0.25 10 false Restart 5.594,2.021 6.177,2.271 0.583,0.25 10 false Restart 5.594,2.406 6.177,2.656 0.583,0.25 10 false Restart 5.604,2.854 6.188,3.104 0.583,0.25 10 false Restart 1.021,3.271 1.604,3.521 0.583,0.25 10 false : Idling 1.875,3.271 2.708,3.563 0.833,0.292 10 false : Idling stop

Shift Lever in D and Current Idling Stop Time 2 Seconds or More
W143071E01
2.219,0.49 3.646,0.781 1.427,0.292 10 false Shift Lever Operation 1.156,1.167 1.469,1.365 0.313,0.198 10 false S 2.042,1.167 2.354,1.365 0.313,0.198 10 false D 2.865,1.167 3.177,1.365 0.313,0.198 10 false N 3.698,1.177 4.01,1.375 0.313,0.198 10 false R 4.542,1.177 4.854,1.375 0.313,0.198 10 false P 5.052,0.427 6.51,1.052 1.458,0.625 10 false Stop and Start System Condition after Shift Lever Operation 1.031,3.646 1.531,3.885 0.5,0.24 10 false : Idling 1.875,3.635 2.844,3.927 0.969,0.292 10 false : Idling stop 5.469,3.156 6.208,3.406 0.74,0.25 10 false Idling Stop 5.458,2.729 6.198,2.979 0.74,0.25 10 false Idling Stop 5.563,2.302 6.115,2.5 0.552,0.198 10 false Restart 5.542,1.885 6.094,2.083 0.552,0.198 10 false Restart 5.552,1.469 6.104,1.667 0.552,0.198 10 false Restart 0.573,5.031 3.448,5.417 2.875,0.385 10 false *b: Shift Lever in N for 0.5 Seconds or More 0.583,5.51 3.458,5.896 2.875,0.385 10 false *c: Shift Lever in R for 0.5 Seconds or More 0.573,4.531 3.448,4.917 2.875,0.385 10 false *a: Shift Lever in S for 0.5 Seconds or More 0.594,6.01 6.729,6.75 6.135,0.74 10 false *d: If the engine restarts due to having the shift lever in N or R for 0.5 seconds or more, such as when moving the shift lever slowly, an idling stop will be performed again with the shift lever in P. 0.594,6.813 6.813,7.49 6.219,0.677 10 false *e: If the shift lever is rapidly moved and is in N or R for less than 0.5 seconds, the idling stop continues regardless of stop and start priority control. 1.458,1.427 1.677,1.646 0.219,0.219 10 false *a 2.781,1.844 3,2.063 0.219,0.219 10 false *b 3.594,2.271 3.813,2.49 0.219,0.219 10 false *c 2.938,2.708 3.156,2.927 0.219,0.219 10 false *d 3.802,2.719 4.021,2.938 0.219,0.219 10 false *d 4.677,2.719 4.896,2.938 0.219,0.219 10 false *d 2.948,3.115 3.167,3.333 0.219,0.219 10 false *e 3.823,3.115 4.042,3.333 0.219,0.219 10 false *e 4.698,3.135 4.917,3.354 0.219,0.219 10 false *e

Shift Lever in P during Idling Stop
W143072E01
2.021,0.771 3.469,1.042 1.448,0.271 10 false Shift Lever Operation 4.573,0.677 6.188,1.26 1.615,0.583 10 false Stop and Start System Condition after Shift Lever Operation 5.083,1.719 5.635,1.99 0.552,0.271 10 false Restart 5.094,2.146 5.667,2.438 0.573,0.292 10 false Restart 5.104,2.552 5.635,2.833 0.531,0.281 10 false Restart 1.104,1.396 1.563,1.615 0.458,0.219 10 false D or S 2.115,1.427 2.354,1.646 0.24,0.219 10 false N 2.979,1.417 3.281,1.667 0.302,0.25 10 false R 3.813,1.417 4.042,1.615 0.229,0.198 10 false P 4.031,1.792 4.188,2 0.156,0.208 10 false * 4.031,2.229 4.146,2.375 0.115,0.146 10 false * 4.031,2.635 4.198,2.781 0.167,0.146 10 false * 1.219,2.958 1.708,3.302 0.49,0.344 10 false : Idling 2.063,2.958 2.802,3.271 0.74,0.313 10 false : Idling stop 0.438,3.583 6.469,4.375 6.031,0.792 10 false *: If the stop light switch is on, the engine restarts when the shift lever is moved out of P. Also, if the stop light switch is off, the engine restarts when the stop light switch is turned on.




DIAGNOSIS


a.

When the engine stop and start ECU detects a malfunction and CAN communication is normal, the engine stop and start ECU records information related to the malfunction. Furthermore, the stop and start indicator light in the combination meter assembly blinks to inform the driver that CAN communication is normal.


b.

The engine stop and start ECU also stores Diagnostic Trouble Codes (DTCs) related to malfunctions. DTCs can be read using the Global TechStream (GTS).