Home › Engine / Hybrid System › 1GD-FTV (ENGINE MECHANICAL) › ENGINE UNIT › from 2020.06
NM35X0E _51 Engine / Hybrid System _080140 1GD-FTV ENGINE MECHANICAL _0389534 ENGINE UNIT DE DETAILS F

1GD-FTV ENGINE MECHANICAL  ENGINE UNIT  DETAILS  CYLINDER HEAD GASKET  


CONSTRUCTION


a.

In order to improve sealing performance, a cylinder head gasket with an independent 2-layer bead and stopper structure is used.


b.

The surface is coated in fluorine rubber to improve sealing performance.


c.

The size of the water holes is optimized for optimal coolant flow volume to each area.

W145226C01
3.104,0.281 3.292,0.688 true 6.198,1.49 6.563,1.104 true 6.198,1.594 6.563,1.396 true 6.208,1.688 6.563,1.688 true 6.208,1.771 6.563,1.99 true 6.208,1.865 6.573,2.333 true 5.719,3.833 5.906,4.167 true 5.698,3.719 5.885,3.417 true 4.938,3.438 5.063,3.74 true 2.594,3.49 2.427,3.74 true 1.646,3.469 1.75,3.719 true 1.635,4.063 1.75,3.833 true 0.781,3.542 0.938,3.74 true 2.979,0.125 3.292,0.281 0.313,0.156 10 false *1 2.594,3.333 2.906,3.49 0.313,0.156 10 false *2 1.552,3.302 1.865,3.458 0.313,0.156 10 false *3 4.104,3.135 4.417,3.292 0.313,0.156 10 false *b 0.448,3.125 0.781,3.344 0.333,0.219 10 false *a 0.677,3.365 0.99,3.521 0.313,0.156 10 false *2 1.5,4.073 1.813,4.229 0.313,0.156 10 false *3 4.833,3.26 5.146,3.417 0.313,0.156 10 false *2 5.906,4.177 6.219,4.333 0.313,0.156 10 false *3 5.854,3.271 6.167,3.427 0.313,0.156 10 false *3 1.927,1.406 2.24,1.563 0.313,0.156 10 false F 2.552,1.406 2.865,1.563 0.313,0.156 10 false F 3.313,1.958 3.438,2.104 0.125,0.146 10 true G 3.313,2.271 3.438,2.417 0.125,0.146 10 true G 6.615,2.313 6.813,2.5 0.198,0.188 10 false A 6.615,1.927 6.813,2.115 0.198,0.188 10 false B 6.615,1.615 6.813,1.802 0.198,0.188 10 false C 6.615,1.302 6.813,1.49 0.198,0.188 10 false D 6.604,1.01 6.802,1.198 0.198,0.188 10 false E
*1 Cylinder Head Gasket Sub-assembly *2 Stopper
*3 Half-bead - -
*a F - F Cross Section *b G - G Cross Section
V100136

Front - -


HINT:

There are 5 sizes of new cylinder head gaskets indicated by the discrimination holes labeled "A", "B", "C", "D" and "E" in accordance with the piston protrusion. For details, refer to the Repair Manual.