| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B150819 | Turn Signal/Hazard Flasher Circuit Current Above Threshold | Diagnosis Condition:
Battery voltage is 10 V or more Malfunction Status:
·
Short in front turn signal light circuit ·
Short in side turn signal light circuit ·
Short in rear turn signal light circuit |
·
Front turn signal light socket ·
Front turn signal light bulb ·
Side turn signal light socket and wire (w/ Front Fender Type Side Turn Signal Light) ·
Side turn signal light bulb (w/ Front Fender Type Side Turn Signal Light) ·
Side turn signal light assembly (w/ Outer Rear View Mirror Type Side Turn Signal Light) ·
Outer mirror retractor (w/ Outer Rear View Mirror Type Side Turn Signal Light) ·
Rear combination light socket and wire sub-assembly ·
Rear turn signal light bulb ·
Combination meter assembly ·
Harness or connector |
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Inspect the bulbs before performing the following procedure.
Inspect the illumination of each turn signal light.
| Result | Proceed to |
|---|---|
| Front turn signal light LH and side turn signal light LH do not blink. | A |
| Front turn signal light RH and side turn signal light RH do not blink. | B |
| Rear turn signal light LH does not blink. | C |
| Rear turn signal light RH does not blink. | D |
A
B
C
D
Check vehicle condition.
| Result | Proceed to |
|---|---|
| w/ Front Fender Type Side Turn Signal Light | A |
| w/ Outer Rear View Mirror Type Side Turn Signal Light | B |
A
B
Disconnect the A19 front turn signal light socket connector.
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
B
Disconnect the A21 side turn signal light socket and wire connector.
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
B
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY (for Front Fender)>REMOVAL
Disconnect the N23 combination meter assembly connector.
Disconnect the A19 front turn signal light socket connector.
Disconnect the A21 side turn signal light socket and wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N23-1 (LL) or A19-2 (B) or A21-1 (B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A19 front turn signal light socket connector.
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
B
Disconnect the R20*1 or R19*2 outer rear view mirror assembly LH connector.
*1: w/ Blind Spot Monitor System
*2: w/o Blind Spot Monitor System
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
B
*1: w/ Blind Spot Monitor System
*2: w/o Blind Spot Monitor System
Disconnect the N23 combination meter assembly connector.
Disconnect the A19 front turn signal light socket connector.
Disconnect the R20*1 or R19*2 outer rear view mirror assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N23-1 (LL) or A19-2 (B) or R20-10 (B) - Body ground*1 | Always | 10 kΩ or higher |
| N23-1 (LL) or A19-2 (B) or R19-5 (B) - Body ground*2 | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the side turn signal light assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY (for Outer Rear View Mirror)>REMOVAL
Reconnect the R20*1 or R19*2 outer rear view mirror assembly LH connector.
*1: w/ Blind Spot Monitor Syastem
*2: w/o Blind Spot Monitor Syastem
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
B
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY (for Outer Rear View Mirror)>REMOVAL
Check vehicle condition.
| Result | Proceed to |
|---|---|
| w/ Front Fender Type Side Turn Signal Light | A |
| w/ Outer Rear View Mirror Type Side Turn Signal Light | B |
A
B
Disconnect the A20 front turn signal light socket connector.
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
B
Disconnect the A22 side turn signal light socket and wire connector.
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
B
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY (for Front Fender)>REMOVAL
Disconnect the N23 combination meter assembly connector.
Disconnect the A20 front turn signal light socket connector.
Disconnect the A22 side turn signal light socket and wire connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N23-2 (LR) or A20-2 (B) or A22-1 (B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A20 front turn signal light socket connector.
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
B
Disconnect the R10*1 or R9*2 outer rear view mirror assembly RH connector.
*1: w/ Blind Spot Monitor System
*2: w/o Blind Spot Monitor System
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
B
*1: w/ Blind Spot Monitor System
*2: w/o Blind Spot Monitor System
Disconnect the N23 combination meter assembly connector.
Disconnect the A20 front turn signal light socket connector.
Disconnect the R10*1 or R9*2 outer rear view mirror assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N23-2 (LR) or A20-2 (B) or R10-10 (B) - Body ground*1 | Always | 10 kΩ or higher |
| N23-2 (LR) or A20-2 (B) or R9-5 (B) - Body ground*2 | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the side turn signal light assembly RH connector.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY (for Outer Rear View Mirror)>REMOVAL
Disconnect the R10*1 or R9*2 outer rear view mirror assembly RH connector.
*1: w/ Blind Spot Monitor Syastem
*2: w/o Blind Spot Monitor Syastem
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
B
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY (for Outer Rear View Mirror)>REMOVAL
Disconnect the e1 rear combination light socket and wire sub-assembly LH connector.
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
B
Disconnect the N23 combination meter assembly connector.
Disconnect the e1 rear combination light socket and wire sub-assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N23-5 (TRNL) or e1-4 (TRN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the g1 rear combination light socket and wire sub-assembly RH connector.
Clear the DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B150819 is output. | A |
| DTC B150718 is output. | B |
A
B
Disconnect the N23 combination meter assembly connector.
Disconnect the g1 rear combination light socket and wire sub-assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N23-6 (TRNR) or g1-4 (TRN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG