Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2019.02–2019.06
RM35X0E _56 Audio / Visual / Telematics _078379 NAVIGATION / MULTI INFO DISPLAY _0380999 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio and display receiver assembly, map light assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1579 Voice Recognition Microphone Disconnected Microphone signal is lost
·

Map light assembly

·

Telephone microphone assembly

·

Radio and display receiver assembly

·

Harness or connector



WIRING DIAGRAM

E402556E20
1.583,0.958 2.042,1.188 0.458,0.229 10 false SNS2 2.052,0.823 2.271,1.01 0.219,0.188 10 false 1 5.448,0.823 5.667,1.01 0.219,0.188 10 false 25 5.771,0.958 6.49,1.25 0.719,0.292 10 false SNS2 2.073,1.844 2.531,2.073 0.458,0.229 10 false 2 5.448,1.823 5.729,2.063 0.281,0.24 10 false 22 5.781,1.969 6.24,2.198 0.458,0.229 10 false MIN- 5.74,2.469 6.198,2.698 0.458,0.229 10 false O7 5.74,2.635 6.969,3.021 1.229,0.385 10 false Radio and Display Receiver Assembly 0.917,3.073 1.375,3.302 0.458,0.229 10 false a19 1.052,2.375 2.479,2.865 1.427,0.49 10 false Telephone Microphone Assembly 0.927,3.229 2.885,3.583 1.958,0.354 10 false Map Light Assembly 2.573,1.854 3.031,2.083 0.458,0.229 10 false MCO- 1.604,1.938 2.063,2.167 0.458,0.229 10 false MIC- 2.604,0.833 3.063,1.063 0.458,0.229 10 false SNS2 3.104,0.833 3.563,1.063 0.458,0.229 10 false 11 3.115,1.844 3.573,2.073 0.458,0.229 10 false 10 1.063,2.208 1.542,2.438 0.479,0.229 10 false A

CAUTION / NOTICE / HINT

NOTICE:

When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:

·

A communication malfunction DTC may be stored.

·

The radio and display receiver assembly may not operate normally.



HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the O7 radio and display receiver assembly connector.


b.

Disconnect the a19 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O7-25 (SNS2) - a19-11 (SNS2) Always Below 1 Ω
O7-22 (MIN-) - a19-10 (MCO-) Always Below 1 Ω
O7-25 (SNS2) - Body ground Always 10 kΩ or higher
O7-22 (MIN-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT MAP LIGHT ASSEMBLY
a.
E408533C02
1.51,0.271 1.885,0.521 0.375,0.25 1.177,1.198 1.063,0.333 1.063,0.333 0.885,0.333 true 1.031,1.177 0.865,0.615 0.865,0.615 0.688,0.615 true 0.125,0.135 0.438,0.333 0.313,0.198 10 false *a 0.458,0.25 0.969,0.458 0.51,0.208 10 false MCO- 0.281,0.531 0.813,0.792 0.531,0.26 10 false SNS2 1.594,0.313 1.906,0.51 0.313,0.198 10 false a19
*a Component without harness connected
(Map Light Assembly)


Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a19-11 (SNS2) - a19-10 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

3.INSPECT MAP LIGHT ASSEMBLY
3.INSPECT MAP LIGHT ASSEMBLY
a.
E408555C03
1.458,0.396 1.844,0.646 0.385,0.25 1.479,2.813 1.875,3.063 0.396,0.25 1,1.313 0.74,0.833 0.74,0.833 0.573,0.833 true 1.458,3.49 1.219,3.896 true 1.917,3.927 1.615,3.479 true 1.146,1.323 0.896,0.583 0.896,0.583 0.729,0.583 true 0.167,0.083 0.479,0.281 0.313,0.198 10 false *a 0.156,0.75 0.656,0.969 0.5,0.219 10 false SNS2 0.302,0.5 0.781,0.708 0.479,0.208 10 false MCO- 1.635,2.854 1.948,3.052 0.313,0.198 10 false A 1.552,0.438 2.031,0.646 0.479,0.208 10 false a19 0.802,3.854 1.302,4.073 0.5,0.219 10 false SNS2 1.979,3.875 2.458,4.083 0.479,0.208 10 false MIC-
*a Component without harness connected
(Map Light Assembly)


Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the telephone microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a19-11 (SNS2) - A-1 (SNS2) Always Below 1 Ω
a19-10 (MCO-) - A-2 (MIC-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE MAP LIGHT ASSEMBLY