This DTC is output when the neutral position switch (close/release) in the power slide door lock assembly RH inputs a malfunction signal during a slide door open operation.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2260 | Power Slide Door Neutral Closer Switch RH Malfunction during Open Operation | Slide door motor unit RH (slide door ECU RH) detects neutral position switch (close/release) malfunction signal in power slide door lock assembly RH during slide door open operation | ·
Power slide door lock assembly RH ·
Slide door motor unit RH (slide door ECU RH) ·
Harness or connector |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
If the replacement, removal and installation of the slide door motor unit (slide door ECU) or disconnection of the connectors of the slide door motor unit (slide door ECU) has been performed, initialize the power slide door system.
Click hereVehicle Exterior>DOOR / HATCH>POWER SLIDE DOOR SYSTEM>INITIALIZATION
Clear the DTC.
Click hereVehicle Exterior>DOOR / HATCH>SLIDE DOOR CLOSER SYSTEM>DTC CHECK / CLEAR
Check for DTC.
Click hereVehicle Exterior>DOOR / HATCH>SLIDE DOOR CLOSER SYSTEM>DTC CHECK / CLEAR
DTC B2260 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *a | Front view of wire harness connector
(to Slide Door Motor Unit RH [Slide Door ECU RH]) |
Disconnect the slide door motor unit RH (slide door ECU RH) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W9-1 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W9-3 (B) - Body ground | Always | 11 to 14 V |
| W9-6 (ECUB) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
Click hereVehicle Exterior>DOOR / HATCH>SLIDE DOOR CLOSER SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|
| Neutral Position Close Switch | Status of the neutral position close switch | ON or OFF | ON: Neutral position close switch on
OFF: Neutral position close switch off |
- |
| Neutral Position Release Switch | Status of the neutral position release switch | ON or OFF | ON: Neutral position release switch on
OFF: Neutral position release switch off |
- |
| Tester Display |
|---|
| Neutral Position Close Switch |
| Neutral Position Release Switch |
The switches switch ON/OFF according to the slide door open/close operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the power slide door lock assembly RH.
Click hereVehicle Interior>DOOR LOCK>SLIDE DOOR LOCK (except Wagon)>REMOVAL
Inspect the power slide door lock assembly RH.
Click hereVehicle Interior>DOOR LOCK>SLIDE DOOR LOCK (except Wagon)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the S3 power slide door lock assembly RH connector.
Disconnect the S4 slide door motor unit RH (slide door ECU RH) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S3-9 (NPC) - S4-4 (P) | Always | Below 1 Ω |
| S3-8 (NPR) - S4-1 (SPD) | Always | Below 1 Ω |
| S3-7 (E1) - Body ground | Always | Below 1 Ω |
| S3-9 (NPC) or S4-4 (P) - Body ground | Always | 10 kΩ or higher |
| S3-8 (NPR) or S4-1 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG