This circuit detects the ignition switch ACC or off condition, and sends it to the main body ECU (multiplex network body ECU).
Inspect the fuses for circuits related to this system before performing the following procedure.
Read the Data List according to the display on the GTS.
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ACC SW | Ignition switch ACC signal | OFF or ON | OFF: Ignition switch off
ON: Ignition switch ACC |
"ON" is also displayed for this item when the ignition switch is ON. |
| Tester Display |
|---|
| ACC SW |
Normal conditions listed above are displayed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the instrument panel junction block assembly connectors.
| *A | for LHD | *B | for RHD |
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
- | - |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3E-1 - Body ground | Always | 11 to 14 V |
| 3A-30 - Body ground | Ignition switch ACC | 11 to 14 V |
| Ignition switch off | Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3G-1 - Body ground | Always | 11 to 14 V |
| 3A-30 - Body ground | Ignition switch ACC | 11 to 14 V |
| Ignition switch off | Below 1 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-3 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
| *A | for LHD | *B | for RHD |
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3E-1 - A-30 (ACC) | Battery not connected to 3A-30 and 3B-3 | 10 kΩ or higher |
| Battery positive (+) → 3A-30
Battery negative (-) → 3B-3 |
Below 1 Ω | |
| 3B-3 - A-11 (GND) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3G-1 - A-30 (ACC) | Battery not connected to 3A-30 and 3B-3 | 10 kΩ or higher |
| Battery positive (+) → 3A-30
Battery negative (-) → 3B-3 |
Below 1 Ω | |
| 3B-3 - A-11 (GND) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D