Home › Engine / Hybrid System › 1GD-FTV (STARTING) › PRE-HEATING SYSTEM
RM35X0E _51 Engine / Hybrid System _078666 1GD-FTV STARTING _0382047 PRE-HEATING SYSTEM G

1GD-FTV STARTING  PRE-HEATING SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

NOTICE:

Turn the ignition switch off for 60 seconds before performing the following inspections.


PROCEDURE

Hide 1.INSPECT ILLUMINATION DURATION OF GLOW INDICATOR LIGHT

a.
A301596C03
1.604,1.417 1.917,1.615 0.313,0.198 10 false *c 0.313,0.948 0.729,1.135 0.417,0.188 10 false (sec.) 0.302,1.302 0.583,1.51 0.281,0.208 10 false 2.0 0.302,1.469 0.583,1.677 0.281,0.208 10 false 1.5 0.292,1.844 0.573,2.042 0.281,0.198 10 false 1.0 0.229,2.115 0.563,2.271 0.333,0.156 10 false 0.72 0.76,2.344 1.052,2.5 0.292,0.156 10 false -25 0.76,2.573 1.052,2.729 0.292,0.156 10 false -13 1.177,2.354 1.469,2.51 0.292,0.156 10 false -15 1.281,2.573 1.573,2.729 0.292,0.156 10 false 5 1.823,2.344 2.115,2.5 0.292,0.156 10 false 0 1.802,2.552 2.094,2.708 0.292,0.156 10 false 32 2.698,2.604 2.99,2.76 0.292,0.156 10 false 68 2.708,2.354 3,2.51 0.292,0.156 10 false 20 3.052,2.344 3.385,2.583 0.333,0.24 10 false (°C) 3.052,2.604 3.406,2.854 0.354,0.25 10 false (°F) 1.573,2.906 1.885,3.104 0.313,0.198 10 false *b 0.177,0.729 0.49,0.927 0.313,0.198 10 false *a
*a Glow Indicator Light Illumination Time
*b Engine Coolant Temperature
*c When atmospheric pressure is 100 kPa (1.0 kgf/cm2)


Turn the ignition switch to ON and measure the length of time that the light remains illuminated.

Light illumination duration:

Refer to the graph


HINT:

Depending on the engine coolant temperature, the indicator light illumination time changes as shown in the illustration.



Hide 2.INSPECT PRE-HEATING FUNCTION

a.

Measure the voltage applied to the glow plug assemblies.

Standard voltage:

11 to 14 V at 25°C (77°F) or less



b.

Measure the length of time that voltage is applied to the glow plug assemblies while the ignition switch is ON.

Standard Pre-heating Time:
Condition Pre-heating Time
Battery voltage at 14.5 V or higher 1 second
Engine coolant temperature 40°C (104°F) or higher 1 second
Other than above 15 seconds



Hide 3.INSPECT AFTER GLOW

a.

Measure the voltage applied to the glow plug assemblies after the engine is started.

Standard Voltage:
Measurement Condition Specified Condition
Engine coolant temperature 20°C (68°F) or less 11 to 14 V
Engine coolant temperature 20°C (68°F) to 41°C (106°F) 0 to 14 V
Engine coolant temperature 41°C (106°F) or higher 0 V


HINT:

The maximum amount of time that voltage is applied to the glow plug assemblies is 20 minutes.