Home › Engine / Hybrid System › 1GD-FTV (STARTING) › STARTER (for 2.0 kW Type)
RM35X0E _51 Engine / Hybrid System _078666 1GD-FTV STARTING _0382050 STARTER(for 2.0 kW Type) A

1GD-FTV STARTING  STARTER(for 2.0 kW Type)  REASSEMBLY  


PROCEDURE

Hide 28226B 1.INSTALL REPAIR SERVICE STARTER KIT

a.
A356494

Install the rubber seal to the repair service starter kit.


b.
A341322C01
1.563,1.458 1.719,1.656 0.156,0.198 10 false .
V100135

High-temperature Grease


Apply high-temperature grease to the planetary gears and pins of the repair service starter kit as shown in the illustration.


c.

Install the 3 planetary gears to the starter center bearing clutch sub-assembly.


Hide 28160 2.INSTALL STARTER ARMATURE ASSEMBLY

a.

Install the starter armature assembly to the starter yoke assembly.

NOTICE:

The magnet of the starter yoke may attract the starter armature assembly when the starter armature assembly is installed, causing the magnet to break.



Hide 28140 3.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.
A368710C02
2.406,1.385 2.656,1.656 2.656,1.656 2.906,1.656 true 2.979,1.594 3.292,1.792 0.313,0.198 10 false *a
*a Retainer


When installing a new part:

NOTICE:

Do not remove the retainer.


i.
A368711C02
0.552,0.729 0.406,0.5 false 1.938,1.49 2.229,1.063 false 0.542,4.25 1.063,3.771 true 0.208,0.365 0.521,0.521 0.313,0.156 10 false *1 1.75,1.49 2.063,1.646 0.313,0.156 10 false *2 0.344,4.219 0.656,4.375 0.313,0.156 10 false *a 1.427,0.583 1.74,0.74 0.313,0.156 10 false *b 0.396,3.573 0.708,3.729 0.313,0.156 10 false *c 1.104,2.542 1.417,2.698 0.313,0.156 10 false *b
*1 Starter Brush Holder Assembly
*2 Starter Armature Assembly
*a Retainer
*b Push Starter Brush Holder Assembly in this Direction
*c Push out Retainer in this Direction


With the retainer installed, push the starter brush holder assembly onto the starter armature assembly.

NOTICE:

Be careful not to damage the brushes when pushing the starter brush holder assembly in place.


HINT:

Install the starter brush holder assembly as shown in the illustration, as the installation direction is fixed.



ii.

Push the starter brush holder assembly onto the starter armature assembly while pushing out the retainer with the end of the starter armature assembly.


iii.
A368712C02
0.354,0.76 0.698,0.99 false 0.156,0.667 0.469,0.823 0.313,0.156 10 false *a 1.146,0.792 1.458,0.948 0.313,0.156 10 false *b
*a Retainer
*b Push out Retainer in this Direction


Push the starter brush holder assembly onto the starter armature assembly until the retainer is completely pushed out.



b.
A372726C02
0.615,0.26 1.198,0.146 false 0.75,0.781 1.25,0.667 false 0.688,2.115 0.292,1.781 0.292,1.781 0.688,1.417 true 1.844,3.198 1.573,2.958 1.573,2.958 1.958,2.677 false 0.688,2.677 0.969,2.677 false 0.396,3.344 0.698,3.594 false 2.323,1.042 2.573,1.26 false 2.083,1.771 2.302,1.875 false 1.854,3.833 2.177,3.833 false 1.833,4.365 2.208,4.313 false 2.406,3.188 2.813,3.646 false 1.458,1.323 1.677,1.271 false 1.281,0.073 1.594,0.229 0.313,0.156 10 false *a 1.344,0.594 1.656,0.75 0.313,0.156 10 false *b 0.073,1.698 0.385,1.854 0.313,0.156 10 false *c 1.375,2.885 1.688,3.042 0.313,0.156 10 false *c 2.115,0.927 2.427,1.083 0.313,0.156 10 false *a 1.906,1.677 2.219,1.833 0.313,0.156 10 false *b 0.781,3.583 1.094,3.74 0.313,0.156 10 false *a 1.656,3.75 1.969,3.906 0.313,0.156 10 false *b 1.656,4.302 1.969,4.458 0.313,0.156 10 false *a 1.052,2.615 1.365,2.771 0.313,0.156 10 false *b 2.927,3.625 3.24,3.823 0.313,0.198 10 false *d 1.75,1.198 2.063,1.396 0.313,0.198 10 false *e 2.896,1.969 3.208,2.167 0.313,0.198 10 false *f
*a Holder Box
*b Spring
*c Brush
*d Rubber Part
*e Holder Plate
*f Rounded Corner of Lead Wire Rubber Part


When reinstalling:

i.

Set the spring inside the holder box. Then, push the brush inside the holder box in the orientation shown in the illustration.

NOTICE:

Install the holder boxes so the rounded corner of the rubber portion of the lead wire faces the holder plate.


HINT:

Install the holder boxes with their claws facing the holder plate.



ii.
A368714C02
0.969,2.521 1.385,2.99 false 2.146,3.448 2.594,3.25 false 0.563,4.427 1.292,4.427 false 2.958,1.115 3.271,1.271 0.313,0.156 10 false *a 2.677,3.167 2.99,3.323 0.313,0.156 10 false *b 0.74,2.406 1.052,2.563 0.313,0.156 10 false *c 2.031,2.406 2.344,2.563 0.313,0.156 10 false *d 0.365,4.344 0.677,4.542 0.313,0.198 10 false *e
*a Range for Wire Used to Fix Brush
*b Brush
*c Holder Box
*d 1 mm or less
*e Claw of the Holder Box


With the brush pushed inside, use wire or similar material to fix the brush in the position shown in the illustration.

NOTICE:
·

When fixing the brush in place using wire or similar material, be careful not to damage the brush.

·

Fix the brush in place so that it protrudes from the holder box by 1 mm or less.




iii.
A368713C02
0.396,2.396 0.771,2.125 false 2.323,1.354 2.76,1.969 false 0.448,4.135 0.969,3.99 true 0.438,3.01 0.969,3.115 true 1.531,3.115 2.063,3.031 true 1.542,3.99 2.073,4.042 true 0.188,2.375 0.5,2.531 0.313,0.156 10 false *a 2.792,2.031 3.104,2.188 0.313,0.156 10 false *b 0.219,2.917 0.531,3.073 0.313,0.156 10 false *c 2.146,2.948 2.458,3.104 0.313,0.156 10 false *c 2.146,3.99 2.458,4.146 0.313,0.156 10 false *c 0.24,4.083 0.552,4.24 0.313,0.156 10 false *c
*a Holder Plate
*b Rounded Corner of Lead Wire Rubber Part
*c Claw of the Holder Box


Insert the claw of the holder box into the holder plate to fix the holder box in place.

NOTICE:
·

Install the holder boxes so the rounded corner of the rubber portion of the lead wire faces the holder plate.

·

Check that the 4 claws of the holder boxes are fixed to the holder plate.




iv.
A368715C02
0.448,0.25 0.802,0.438 false 1,0.292 1.271,0.115 false 0.479,1.469 1,1.115 true 1.552,1.552 1.406,1.083 false 0.635,2.781 1.083,3.052 false 0.25,0.177 0.563,0.333 0.313,0.156 10 false *1 1.542,1.625 1.854,1.781 0.313,0.156 10 false *2 0.073,0.76 0.385,0.917 0.313,0.156 10 false *a 1.323,0.063 1.635,0.219 0.313,0.156 10 false *b 0.188,3.417 0.5,3.573 0.313,0.156 10 false *a 0.26,1.448 0.573,1.604 0.313,0.156 10 false *b 0.427,2.708 0.74,2.865 0.313,0.156 10 false *1
*1 Starter Brush Holder Assembly
*2 Starter Armature Assembly
*a Push Starter Brush Holder Assembly in this Direction
*b Assembly in this Direction Wire


Push the starter brush holder assembly onto the starter armature assembly, but leave enough room to remove the wire or similar material.


v.

Remove the 4 pieces of wire or similar material and then push the starter brush holder assembly all the way onto the starter armature assembly.

NOTICE:

When removing the wire or similar material, be careful not to damage the brush.




Hide 4.INSTALL STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A377035C02
2.229,0.146 2.375,0.146 2.375,0.146 2.479,0.344 false 2.906,0.427 2.99,0.167 2.99,0.167 3.156,0.167 true 2.063,0.083 2.375,0.281 0.313,0.198 10 false *a 3.208,0.104 3.406,0.344 0.198,0.24 10 false *b
*a Rubber Part
*b Starter Commutator End Frame Assembly


Align the rubber part of the starter yoke assembly with the groove of the starter commutator end frame assembly.


b.

Install the starter commutator end frame assembly with the 2 screws.

Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)


Hide 28120 5.INSTALL STARTER YOKE ASSEMBLY

a.

Install the starter armature plate to the starter yoke assembly.


b.
A224840C03
2.198,1.302 2.583,0.583 2.583,0.583 2.75,0.583 true 2.875,1.781 2.875,1.146 2.875,1.146 3.042,1.146 true 2.802,0.51 3.115,0.667 0.313,0.156 10 false *a 3.083,1.063 3.313,1.229 0.229,0.167 10 false *b
*a Protrusion
*b Notch


Check that the notch of the starter armature plate fits over the protrusion of the starter yoke assembly.


c.
A341323C01
1.74,1.438 1.906,1.854 1.906,1.854 2.073,1.854 false 2.365,1.271 2.531,1.688 2.531,1.688 2.698,1.688 true 2.76,1.594 3.073,1.792 0.313,0.198 10 false *a 2.135,1.771 2.448,1.969 0.313,0.198 10 false *b
*a Notch
*b Protrusion


Align the protrusion of the starter yoke assembly with the notches inside the repair service starter kit and insert the starter yoke assembly into the repair service starter kit.


d.

Using a T25 "TORX" socket wrench, install the repair service starter kit with the 2 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 28150 6.INSTALL MAGNET STARTER SWITCH ASSEMBLY

a.

Apply high-temperature grease to the plunger hook of the magnet starter switch assembly.


b.
A341229

Hang the plunger of the magnet starter switch assembly on the starter pinion drive lever from the upper side.


c.

Install the magnet starter switch assembly with the 2 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


d.

Connect the lead wire to terminal C with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)