Home › Engine / Hybrid System › 1GD-FTV (STARTING) › STARTER (for 3.0 kW Type)
RM35X0E _51 Engine / Hybrid System _078666 1GD-FTV STARTING _0382051 STARTER(for 3.0 kW Type) A

1GD-FTV STARTING  STARTER(for 3.0 kW Type)  DISASSEMBLY  


PROCEDURE

Hide 28120 1.REMOVE STARTER YOKE ASSEMBLY

a.
A437463

Remove the nut and disconnect the lead wire from terminal C.


b.

Remove the 2 bolts.


c.

Pull out the starter yoke assembly together with the starter armature assembly from the magnet starter switch assembly.


Hide 28150 2.REMOVE MAGNET STARTER SWITCH ASSEMBLY

a.
A437464

Remove the 3 screws and magnet starter switch assembly.


b.
A437513C01
1.458,0.531 1.135,0.219 1.135,0.219 1,0.219 false 1.406,0.833 1,0.438 1,0.438 0.875,0.438 false 1.177,0.969 0.896,0.677 0.896,0.677 0.76,0.677 false 0.667,1.375 0.542,1.521 0.542,1.521 0.438,1.521 false 0.656,1.813 0.729,1.979 0.729,1.979 0.844,1.979 false 1.448,1.771 1.604,1.969 1.604,1.969 1.76,1.969 false 2.594,0.438 2.75,0.281 2.75,0.281 2.875,0.281 false 0.865,1.115 0.531,0.844 0.531,0.844 0.396,0.844 false 0.792,0.125 0.958,0.271 0.167,0.146 10 false *2 0.667,0.344 0.833,0.49 0.167,0.146 10 false *3 0.542,0.594 0.708,0.74 0.167,0.146 10 false *5 0.198,0.781 0.365,0.927 0.167,0.146 10 false *4 0.854,1.885 1.021,2.031 0.167,0.146 10 false *1 1.792,1.885 1.958,2.031 0.167,0.146 10 false *6 2.875,0.177 3.042,0.333 0.167,0.156 10 false *7 0.25,1.448 0.417,1.594 0.167,0.146 10 false *8
*1 Return Spring
*2 Pinion Gear
*3 Idler Gear
*4 Clutch Roller
*5 Retainer
*6 Starter Clutch Sub-assembly
*7 Starter Drive Housing Assembly
*8 Plate Washer


Remove the return spring, pinion gear, idler gear, clutch roller, retainer, plate washer and starter clutch sub-assembly from the starter drive housing assembly.


c.
A197146C01
2.427,0.188 2.573,0.188 2.573,0.188 2.573,1.344 false 2.146,0.094 2.333,0.25 0.188,0.156 10 false *a
*a Magnet Hand


Using a magnet hand, remove the steel ball from the clutch shaft hole.


Hide 28140 3.REMOVE STARTER BRUSH HOLDER ASSEMBLY

a.
A102621

Disconnect the 4 starter yoke brushes from the starter brush holder assembly.

i.

Using a screwdriver, pull back the spring.


ii.

Disconnect the brush from the starter brush holder assembly.



b.

Remove the starter brush holder assembly from the starter yoke assembly.


c.

Remove the O-ring.


d.

Remove the 4 screws and 4 brushes from the starter yoke assembly.


Hide 28160 4.REMOVE STARTER ARMATURE ASSEMBLY

a.

Place matchmarks on the starter yoke assembly and starter commutator end frame assembly.


b.

Remove the starter armature assembly together with the starter commutator end frame assembly.


c.

Remove the O-ring.


d.
A102604

Using a plastic-faced hammer, tap the starter commutator end frame assembly to remove the starter armature assembly from the starter commutator end frame assembly.