Home › Engine / Hybrid System › 1GD-FTV (STARTING) › STARTER (for 3.0 kW Type)
RM35X0E _51 Engine / Hybrid System _078666 1GD-FTV STARTING _0382051 STARTER(for 3.0 kW Type) A

1GD-FTV STARTING  STARTER(for 3.0 kW Type)  REASSEMBLY  


PROCEDURE

Hide 28160 1.INSTALL STARTER ARMATURE ASSEMBLY

a.
A102618

Apply high-temperature grease to the armature bearings.


b.

Using a press, press the starter armature assembly into the starter commutator end frame assembly.


c.

Install a new O-ring to the starter yoke assembly.


d.
A102619C01
1.875,0.396 0.865,0.146 0.865,0.146 0.771,0.146 false 1.917,1.042 1.719,1.385 1.719,1.385 1.625,1.385 false 0.563,0.073 0.875,0.229 0.313,0.156 10 false *a 1.448,1.313 1.76,1.469 0.313,0.156 10 false *b
*a Groove
*b Claw


Align the groove of the starter commutator end frame assembly with the claw of the starter yoke assembly, and install the starter armature assembly and starter commutator end frame assembly.


Hide 28140 2.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.

Install the 4 brushes to the starter yoke assembly with the 4 screws.

Torque:
3.6 N*m (37 kgf*cm, 32 in.*lbf)


b.
A102620C01
1.698,1.396 0.844,0.427 0.844,0.427 0.729,0.427 false 1.688,1.5 1.458,1.781 1.458,1.781 1.365,1.781 false 1.146,1.698 1.458,1.854 0.313,0.156 10 false *a 0.531,0.354 0.844,0.51 0.313,0.156 10 false *b
*a Groove
*b Claw


Align the claw of the starter brush holder assembly with the groove of the starter yoke assembly.


c.

Place the starter brush holder assembly on the starter yoke assembly.


d.
A102621

Connect the 4 brushes to the starter brush holder assembly.

i.

Using a screwdriver, pull back the spring.


ii.

Connect the brush to the starter brush holder assembly.

NOTICE:

Make sure that the positive (+) lead wires are not grounded.




e.

Install a new O-ring to the starter yoke assembly.


Hide 28150 3.INSTALL MAGNET STARTER SWITCH ASSEMBLY

a.

Apply high temperature grease to the steel ball, return spring, clutch roller, retainer, pinion gear and idler gear.


b.
A197147

Insert the steel ball into the starter clutch hole.


c.

Insert the return spring into the starter clutch hole.


d.
A437513C01
1.458,0.531 1.135,0.219 1.135,0.219 1,0.219 false 1.406,0.833 1,0.438 1,0.438 0.875,0.438 false 1.177,0.969 0.896,0.677 0.896,0.677 0.76,0.677 false 0.667,1.375 0.542,1.521 0.542,1.521 0.438,1.521 false 0.656,1.813 0.729,1.979 0.729,1.979 0.844,1.979 false 1.448,1.771 1.604,1.969 1.604,1.969 1.76,1.969 false 2.594,0.438 2.75,0.281 2.75,0.281 2.875,0.281 false 0.865,1.115 0.531,0.844 0.531,0.844 0.396,0.844 false 0.792,0.125 0.958,0.271 0.167,0.146 10 false *2 0.667,0.344 0.833,0.49 0.167,0.146 10 false *3 0.542,0.594 0.708,0.74 0.167,0.146 10 false *5 0.198,0.781 0.365,0.927 0.167,0.146 10 false *4 0.854,1.885 1.021,2.031 0.167,0.146 10 false *1 1.792,1.885 1.958,2.031 0.167,0.146 10 false *6 2.875,0.177 3.042,0.333 0.167,0.156 10 false *7 0.25,1.448 0.417,1.594 0.167,0.146 10 false *8
*1 Return Spring
*2 Pinion Gear
*3 Idler Gear
*4 Clutch Roller
*5 Retainer
*6 Starter Clutch Sub-assembly
*7 Starter Drive Housing Assembly
*8 Plate Washer


Install the starter clutch sub-assembly, return spring, idler gear, pinion gear, retainer, clutch roller and plate washer.


e.

Install the magnet starter switch assembly to the starter drive housing assembly with the 3 screws.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 28120 4.INSTALL STARTER YOKE ASSEMBLY

a.
A102623C01
1.094,0.531 1.188,0.531 1.188,0.531 1.427,0.74 false 2.229,1.281 2.292,1.281 2.292,1.281 2.635,0.417 false 0.906,0.458 1.219,0.615 0.313,0.156 10 false *a 2.031,1.198 2.344,1.354 0.313,0.156 10 false *b
*a Claw
*b Groove


Align the claw of the starter brush holder assembly with the groove of the magnet starter switch assembly and install the starter yoke assembly to the magnet starter switch assembly.


b.

Install the starter yoke assembly to the starter drive housing assembly with the 2 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


c.

Connect the lead wire to terminal C with the nut.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)