Home › Engine / Hybrid System › 1GD-FTV (STARTING) › STARTER (w/ Stop And Start System)
RM35X0E _51 Engine / Hybrid System _078666 1GD-FTV STARTING _0382052 STARTER(w/ Stop And Start System) G

1GD-FTV STARTING  STARTER(w/ Stop And Start System)  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. Otherwise, the cable may become hot and cause injury.


NOTICE:

These tests must be performed within 3 to 5 seconds to avoid burning out the coil.


HINT:

When replacing the starter assembly, it is necessary to replace the starter relay (ST) and starter relay (ST No. 2).


a.

Mount the starter assembly in a vise between aluminum plates.


b.

Perform a no-load performance test.

i.
A350369C01
1.719,2.427 1.885,2.427 1.885,2.427 1.563,2.094 true 0.677,3.063 0.844,3.063 0.844,3.063 1.052,3 true 0.354,2.99 0.677,3.167 0.323,0.177 10 false SL1 1.521,2.333 1.844,2.51 0.323,0.177 10 false *a
*a Starter Body
V100135

Moves Outward


Connect the positive (+) lead to terminal SL1.


ii.

Connect the negative (-) lead to the starter body and check that the clutch pinion gear moves outward.

NOTICE:

Be careful when connecting the leads, as the starter assembly may be damaged if the leads are connecting to the wrong locations.


If the clutch pinion gear does not extend, replace the starter assembly, starter relay (ST) and starter relay (ST No. 2).


iii.
A350370C01
1.052,3.01 0.813,3.125 0.813,3.125 0.604,3.125 true 1.542,2.063 1.833,2.396 1.833,2.396 1.698,2.396 true 1.49,2.313 1.802,2.51 0.313,0.198 10 false *a 0.281,3.073 0.594,3.271 0.313,0.198 10 false SL1
*a Starter Body
V100135

Return Inward
V100136

Disconnect


With the clutch pinion gear in the outward position, disconnect the negative (-) lead and check that the clutch pinion gear returns inward.

If the clutch pinion gear does not return inward, replace the starter assembly, starter relay (ST) and starter relay (ST No. 2).


iv.
A350371C01
0.552,2.521 0.74,2.521 0.74,2.521 1.042,2.771 true 2,2.417 2.188,2.417 2.188,2.417 1.594,2.094 true 0.281,2.458 0.594,2.656 0.313,0.198 10 false SL2 1.781,2.323 2.094,2.521 0.313,0.198 10 false *a
*a Starter Body


Connect the positive (+) lead to terminal SL2 of the connector and the negative (-) lead to the starter body. Check that a clicking sound is heard from the starter motor.

NOTICE:

Be careful when connecting the leads, as the starter assembly may be damaged if the leads are connecting to the wrong locations.


If the result is not as specified, replace the starter assembly, starter relay (ST) and starter relay (ST No. 2).


v.

Connect the battery and an ammeter (AC/DC 400 A probe) to the starter assembly as shown in the illustration.

A352286C01
3.5,0.771 3.188,0.521 3.188,0.521 3.021,0.521 true 4.219,1.729 4.656,0.969 4.656,0.969 4.854,0.969 true 3.75,0.302 3.854,0.177 3.854,0.177 4,0.177 true 2.135,1.938 1.969,1.719 1.969,1.719 1.802,1.719 true 2.135,2.135 2.042,2.323 2.042,2.323 1.875,2.323 true 2.802,0.427 3.115,0.583 0.313,0.156 10 false *a 4.906,0.896 5.219,1.052 0.313,0.156 10 false *b 4.063,0.094 4.375,0.25 0.313,0.156 10 false *c 1.542,1.677 1.854,1.833 0.313,0.156 10 false SL2 1.594,2.229 1.906,2.385 0.313,0.156 10 false SL1
*a Terminal 30 *b Starter Body
*c AC/DC 400 A Probe - -


NOTICE:

Be careful when connecting the leads, as the starter assembly may be damaged if the leads are connecting to the wrong locations.



vi.

Connect the negative (-) battery cable and measure the current after the ammeter (AC/DC 400 A probe) reading has stabilized.

Standard current:

210 A or less at 11 V


HINT:

When replacing the starter assembly, it is necessary to replace the starter relay (ST) and starter relay (ST No. 2).


If the result is not as specified, replace the starter assembly, starter relay (ST) and starter relay (ST No. 2).



c.

Check the starter clutch.

i.
A350841C01
0,0 0,0 false
V100135

Free
V100136

Lock


Rotate the clutch pinion gear clockwise and check that it turns freely. Try to rotate the clutch pinion gear counterclockwise and check that it locks.

HINT:

When replacing the starter assembly, it is necessary to replace the starter relay (ST) and starter relay (ST No. 2).


If the result is not as specified, replace the starter assembly, starter relay (ST) and starter relay (ST No. 2).