Home › Drivetrain › RC60J (MANUAL TRANSMISSION / TRANSAXLE) › INPUT SHAFT
RM35X0E _52 Drivetrain _078740 RC60J MANUAL TRANSMISSION / TRANSAXLE _0382064 INPUT SHAFT G

RC60J MANUAL TRANSMISSION / TRANSAXLE  INPUT SHAFT  INSPECTION  


PROCEDURE

Hide 33311 1.INSPECT INPUT SHAFT

a.
C333990

Using a dial indicator and 2 V-blocks, measure the input shaft runout.

Maximum Runout:

0.03 mm (0.00119 in.)


If the runout is more than the maximum, replace the input shaft.

HINT:

Measure the 3 areas shown in the illustration with the input shaft level.



b.
C325180N01
1.26,4.198 1.26,3.875 false 2.271,4.24 2.271,3.917 false 2.594,4.219 2.594,3.906 false 2.865,4.208 2.865,3.896 false 3.219,4.219 3.219,3.865 false 1.24,4.25 1.396,4.448 0.156,0.198 10 false A 2.24,4.25 2.396,4.448 0.156,0.198 10 false B 2.563,4.24 2.74,4.448 0.177,0.208 10 false C 2.844,4.229 3,4.427 0.156,0.198 10 false D 3.188,4.25 3.344,4.448 0.156,0.198 10 false E

Using a micrometer, measure the journal diameter of each input shaft journal at the specified positions.

Standard Journal Diameter:
Item Specified Condition
Journal A 34.009 to 34.022 mm (1.3389 to 1.3394 in.)
Journal B 44.985 to 45.000 mm (1.7711 to 1.7716 in.)
Journal C 44.985 to 45.000 mm (1.7711 to 1.7716 in.)
Journal D 41.985 to 42.000 mm (1.6530 to 1.6535 in.)
Journal E 32.967 to 32.98 mm (1.2980 to 1.2984 in.)


Minimum Diameter:
Item Specified Condition
Journal A 34.009 mm (1.3389 in.)
Journal B 44.985 mm (1.7711 in.)
Journal C 44.985 mm (1.7711 in.)
Journal D 41.985 mm (1.6530 in.)
Journal E 32.967 mm (1.2980 in.)


If the journal diameter is less than the minimum, replace the input shaft.


Hide 33336 2.INSPECT 5TH GEAR

a.
C325182

Using a cylinder gauge, measure the inside diameter of the 5th gear.

Standard Inside Diameter:

53.013 to 53.029 mm (2.0872 to 2.0877 in.)


Maximum Inside Diameter:

53.029 mm (2.0877 in.)


If the inside diameter is more than the maximum, replace the 5th gear.


Hide 33337 3.INSPECT 6TH GEAR SUB-ASSEMBLY

a.
C325181

Using a cylinder gauge, measure the inside diameter of the 6th gear sub-assembly.

Standard Inside Diameter:

51.015 to 51.040 mm (2.0085 to 2.0094 in.)


Maximum Inside Diameter:

51.040 mm (2.0094 in.)


If the inside diameter is more than the maximum, replace the 6th gear sub-assembly.


Hide 33333 4.INSPECT 3RD GEAR

a.
F051116

Using a cylinder gauge, measure the inside diameter of the 3rd gear.

Standard Inside Diameter:

51.015 to 51.040 mm (2.0085 to 2.0094 in.)


Maximum Inside Diameter:

51.040 mm (2.0094 in.)


If the inside diameter is more than the maximum, replace the 3rd gear.


Hide 33364 5.INSPECT NO. 2 TRANSMISSION HUB SLEEVE

a.
C325183

Check the sliding condition between the No. 2 transmission hub and No. 2 transmission hub sleeve.


b.

Check that the splines of the No. 2 transmission hub sleeve are not worn.


c.
C325184N02
2.073,0.24 2.229,0.438 0.156,0.198 10 false A 2.104,4.302 2.26,4.5 0.156,0.198 10 false B 1.917,2.333 2.073,2.531 0.156,0.198 10 false B

Using a vernier caliper, measure the width of the No. 2 transmission hub sleeve groove (A) and the thickness of the claw part of the No. 2 or No. 3 gear shift forks (B), and calculate the clearance.

Standard Clearance (A - B):
Item Specified Condition
No. 2 gear shift fork 0.28 to 0.84 mm (0.0110 to 0.0331 in.)
No. 3 gear shift fork 0.28 to 0.84 mm (0.0110 to 0.0331 in.)


If the clearance is outside the specification, replace the No. 2 transmission hub sleeve and gear shift fork.


Hide 33369 6.INSPECT NO. 3 SYNCHRONIZER RING (for 5th Gear)

a.
C325185

Using a feeler gauge, measure the clearance between the No. 3 synchronizer ring and 5th gear.

Standard Clearance:

0.77 to 1.63 mm (0.0304 to 0.0641 in.)


Minimum Clearance:

0.77 mm (0.0304 in.)


If the clearance is less than the minimum, replace the No. 3 synchronizer ring.


b.

Coat the 5th gear cone with gear oil.


c.
C325186

Check the braking effect of the No. 3 synchronizer ring.

i.

Turn the No. 3 synchronizer ring in both directions while pushing it against the 5th gear cone. Check that the ring locks in both directions. If the No. 3 synchronizer ring turns, replace it.



Hide 33369 7.INSPECT NO. 3 SYNCHRONIZER RING (for 6th Gear)

a.
F051611

Using a feeler gauge, measure the clearance between the No. 3 synchronizer ring and 6th gear.

Standard Clearance:

0.77 to 1.63 mm (0.0304 to 0.0641 in.)


Minimum Clearance:

0.77 mm (0.0304 in.)


If the clearance is less than the minimum, replace the No. 3 synchronizer ring.


b.

Coat the 6th gear cone with gear oil.


c.
C325186

Check the braking effect of the No. 3 synchronizer ring.

i.

Turn the No. 3 synchronizer ring in both directions while pushing it against the 6th gear cone. Check that the ring locks in both directions. If the No. 3 synchronizer ring turns, replace it.



Hide 33039 8.INSPECT NO. 3 SYNCHRONIZER RING SET

a.
C325187

Using a feeler gauge, measure the clearance between the synchronizer ring and 3rd gear.

Standard Clearance:

0.86 to 2.02 mm (0.0339 to 0.0795 in.)


Minimum Clearance:

0.86 mm (0.0339 in.)


If the clearance is less than the minimum, replace the No. 3 synchronizer ring set.


b.

Coat the 3rd gear cone with gear oil.


c.
C325188

Check the braking effect of the synchronizer ring.

i.

Turn the synchronizer ring in both directions while pushing it against the 3rd gear cone. Check that the ring locks in both directions. If the No. 3 synchronizer ring set turns, replace it.



Hide 33342C 9.INSPECT 3RD GEAR THRUST WASHER

a.
C325189

Using a micrometer, measure the 3rd gear thrust washer thickness.

Standard Thickness:

7.62 to 7.68 mm (0.3000 to 0.3023 in.)


Minimum Thickness:

7.62 mm (0.3000 in.)


If the thickness is less than the minimum, replace the 3rd gear thrust washer.