Home › Drivetrain › RC60J (MANUAL TRANSMISSION / TRANSAXLE) › COUNTER GEAR
RM35X0E _52 Drivetrain _078740 RC60J MANUAL TRANSMISSION / TRANSAXLE _0382066 COUNTER GEAR A

RC60J MANUAL TRANSMISSION / TRANSAXLE  COUNTER GEAR  DISASSEMBLY  


PROCEDURE

Hide 33425 1.INSPECT COUNTERSHAFT REVERSE GEAR THRUST CLEARANCE

a.
C325190

Using a dial indicator, measure the countershaft reverse gear thrust clearance.

Standard Clearance:

0.150 to 0.300 mm (0.00591 to 0.0118 in.)


If the clearance is outside the specification, replace the countershaft reverse gear, reverse gear bearing inner race or No. 4 transmission clutch hub.

HINT:

Replace the part or parts determined to be the most likely cause of the problem.



Hide 33425 2.INSPECT COUNTERSHAFT REVERSE GEAR RADIAL CLEARANCE

a.
C325193

Using a dial indicator, measure the countershaft reverse gear radial clearance.

Standard Clearance:

0.015 to 0.067 mm (0.000591 to 0.00263 in.)


If the clearance is outside the specification, replace the countershaft reverse gear, reverse gear bearing inner race or needle roller bearing.

HINT:

Replace the part or parts determined to be the most likely cause of the problem.



Hide 33426A 3.INSPECT COUNTERSHAFT 1ST SPEED GEAR THRUST CLEARANCE

a.
C325191

Using a dial indicator, measure the countershaft 1st speed gear thrust clearance.

Standard Clearance:

0.150 to 0.480 mm (0.00591 to 0.0188 in.)


If the clearance is outside the specification, replace the countershaft 1st speed gear, clutch hub or counter gear.

HINT:

Replace the part or parts determined to be the most likely cause of the problem.



Hide 33426A 4.INSPECT COUNTERSHAFT 1ST SPEED GEAR RADIAL CLEARANCE

a.
C325194

Using a dial indicator, measure the countershaft 1st speed gear radial clearance.

Standard Clearance:

0.015 to 0.067 mm (0.000591 to 0.00263 in.)


If the clearance is outside the specification, replace the countershaft 1st speed gear, 1st gear needle roller bearing or shaft.

HINT:

Replace the part or parts determined to be the most likely cause of the problem.



Hide 33424 5.INSPECT COUNTERSHAFT 2ND SPEED GEAR THRUST CLEARANCE

a.
C334168

Using a dial indicator, measure the countershaft 2nd speed gear thrust clearance.

Standard Clearance:

0.150 to 0.480 mm (0.00591 to 0.0188 in.)


If the clearance is outside the specification, replace the countershaft 2nd speed gear, clutch hub or counter gear.

HINT:

Replace the part or parts determined to be the most likely cause of the problem.



Hide 33424 6.INSPECT COUNTERSHAFT 2ND SPEED GEAR RADIAL CLEARANCE

a.
C325195

Using a dial indicator, measure the countershaft 2nd speed gear radial clearance.

Standard Clearance:

0.015 to 0.067 mm (0.000591 to 0.00263 in.)


If the clearance is outside the specification, replace the countershaft 2nd speed gear, 2nd gear needle roller bearing or shaft.

HINT:

Replace the part or parts determined to be the most likely cause of the problem.



Hide 33411R 7.REMOVE REAR COUNTER GEAR BEARING SNAP RING

a.
C323239

Using a snap ring expander, remove the rear counter gear bearing snap ring from the counter gear.


Hide 33411H 8.REMOVE REAR COUNTER GEAR BEARING OR ROLLER

a.
C323240N01
2.667,0.677 2.885,0.458 false 2.625,1.5 3.042,1.823 false 2.938,0.354 3.323,0.552 0.385,0.198 10 false SST 2.979,1.885 3.365,2.083 0.385,0.198 10 false SST

Using SST, remove the rear counter gear bearing or roller (inner races) from the counter gear.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04010, 09954-04010, 09955-04071, 09957-04010, 09958-04011)
09950-60011  (09951-00320)


Hide 33425 9.REMOVE COUNTERSHAFT REVERSE GEAR

a.
C323242C02
1.552,0.615 1.875,0.333 false 1.552,0.802 1.875,0.604 false 1.75,0.979 1.958,0.896 false 1.927,0.188 2.24,0.344 0.313,0.156 10 false *1 1.938,0.479 2.25,0.635 0.313,0.156 10 false *2 2.01,0.781 2.323,0.938 0.313,0.156 10 false *3
*1 Front Counter Gear Bearing or Roller
*2 Center Counter shaft Bearing
*3 Countershaft Reverse Gear


Using SST and a press, remove the front counter gear bearing or roller, center counter shaft bearing, and countershaft reverse gear from the counter gear.

SST
09555-55010  
09950-70010  (09951-07100)
09950-60011  (09951-00320)

NOTICE:

Support the counter gear by hand so that it does not fall.



Hide 33331A 10.REMOVE REVERSE GEAR BEARING

a.

Remove the reverse gear bearing and reverse gear bearing inner race from the countershaft reverse gear.


Hide 33338C 11.REMOVE REVERSE SHIFT RESTRICT BALL

a.

Remove the reverse shift restrict ball from the counter gear.


Hide 33387A 12.REMOVE REVERSE SYNCHRONIZER RING

a.

Remove the reverse synchronizer ring from the counter gear.


Hide 33392 13.REMOVE NO. 3 SYNCHROMESH SHIFTING KEY SPRING

a.

Remove the No. 3 synchromesh shifting key spring from the counter gear.


Hide 33394 14.REMOVE NO. 3 SYNCHROMESH SHIFTING KEY

a.

Remove the 2 No. 3 synchromesh shifting keys from the counter gear.


Hide 33327 15.REMOVE NO. 4 TRANSMISSION HUB SLEEVE

a.

Remove the No. 4 transmission hub sleeve from the No. 4 transmission clutch hub.


Hide 33352B 16.REMOVE NO. 4 TRANSMISSION CLUTCH HUB

a.
C334169N01
1.031,3.01 1.417,3.01 1.417,3.01 1.958,2.708 true 2.594,1.781 2.844,1.49 2.844,1.49 2.583,1.469 true 0.719,2.927 1.177,3.125 0.458,0.198 10 false SST 2.906,1.438 3.365,1.635 0.458,0.198 10 false SST

Using SST and a press, remove the No. 4 transmission clutch hub and countershaft 1st speed gear from the counter gear.

SST
09555-55010  
09950-70010  (09951-07100)
09950-60011  (09951-00320)

NOTICE:
·

Do not insert SST deep inside the gear, as this may damage the synchronizer ring.

·
C334170N01
0.698,1.167 0.51,0.24 0.51,0.24 2.615,1.198 true 0.146,0.135 0.604,0.333 0.458,0.198 10 false SST

Use SST in the position shown in the illustration.




Hide 33335C 17.REMOVE 1ST GEAR NEEDLE ROLLER BEARING

a.

Remove the 1st gear needle roller bearing from the counter gear.


Hide 33037B 18.REMOVE NO. 1 SYNCHRONIZER RING SET

a.

Remove the No. 1 synchronizer ring set from the counter gear.


Hide 33363 19.REMOVE NO. 1 TRANSMISSION HUB SLEEVE

a.

Remove the No. 1 transmission hub sleeve from the No. 1 transmission clutch hub.


Hide 33365 20.REMOVE NO. 1 SYNCHROMESH SHIFTING KEY

a.

Remove the 3 No. 1 synchromesh shifting keys from the No. 1 transmission clutch hub.


Hide 33361B 21.REMOVE NO. 1 CLUTCH HUB SHAFT SNAP RING

a.
C323432

Using a snap ring expander, remove the No. 1 clutch hub shaft snap ring from the counter gear.


Hide 33361 22.REMOVE NO. 1 TRANSMISSION CLUTCH HUB

a.
C323433N01
2.646,1.25 2.833,1.271 2.833,1.271 2.688,1.427 false 1.281,3.052 2.135,2.75 true 2.896,1.188 3.354,1.385 0.458,0.198 10 false SST 0.906,2.969 1.365,3.167 0.458,0.198 10 false SST

Using SST and a press, remove the countershaft 2nd speed gear, No. 2 synchronizer ring set and No. 1 transmission clutch hub from the counter gear.

SST
09555-55010  
09950-70010  (09951-07100)
09950-60011  (09951-00320)


Hide 33332B 23.REMOVE 2ND GEAR NEEDLE ROLLER BEARING

a.

Remove the 2nd gear needle roller bearing from the counter gear.