Home › Drivetrain › AC60E (AUTOMATIC TRANSMISSION / TRANSAXLE) › OIL COOLER (for 1GD-FTV)
RM35X0E _52 Drivetrain _078741 AC60E AUTOMATIC TRANSMISSION / TRANSAXLE _0382310 OIL COOLER(for 1GD-FTV) A

AC60E AUTOMATIC TRANSMISSION / TRANSAXLE  OIL COOLER(for 1GD-FTV)  INSTALLATION  


PROCEDURE

Hide 32921 1.INSTALL NO. 1 OIL COOLER INLET TUBE AND NO. 1 OIL COOLER OUTLET TUBE

a.

Install the 3 transmission oil cooler tube clamp sub-assemblies to the automatic transmission assembly and engine assembly with the 3 bolts (A).

Torque:
13.5 N*m (138 kgf*cm, 10 ft.*lbf)

NOTICE:

When installing the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube, support the tube by hand and be careful to prevent the tube from being deformed.


C412692C02
5.083,0.833 5,0.833 5,0.833 4.708,0.917 true 4.5,0.542 4.75,0.542 true 5.667,1.417 5.833,1.417 true 2.385,0.833 2.385,1.042 2.385,1.042 2.302,1.042 true 5.125,0.75 5.292,0.917 0.167,0.167 10 false *1 4.292,0.458 4.458,0.625 0.167,0.167 10 true *2 2.094,0.958 2.26,1.125 0.167,0.167 10 false *2 5.458,1.333 5.625,1.5 0.167,0.167 10 true *2
*1 No. 1 Automatic Transmission Oil Cooler Tube Clamp *2 Transmission Oil Cooler Tube Clamp Sub-assembly
V100135

Bolt A
V100136

Bolt B



b.

Connect the ends of the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube to the automatic transmission assembly by hand.


c.

Close the No. 1 automatic transmission oil cooler tube clamp and 2 transmission oil cooler tube clamp sub-assemblies and install the 3 bolts (B).

Torque:
5.2 N*m (53 kgf*cm, 46 in.*lbf)


d.
C410494C01
2.083,1.25 2.25,1.417 0.167,0.167 10 false *a
*a Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, tighten the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube.

Torque:
Specified tightening torque : 34.3 N*m (350 kgf*cm, 25 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.181 in.)) + torque wrench (fulcrum length of 180 mm (7.087 in.)): 29.4 N*m (300 kgf*cm, 22 ft.*lbf)




Hide 32941 2.INSTALL NO. 1 OIL COOLER INLET HOSE AND NO. 1 OIL COOLER OUTLET HOSE

a.
C410493C01
0.333,2.75 0.5,2.75 0.5,2.75 0.75,2.417 true 0.417,3.083 0.583,3.083 0.583,3.083 0.833,2.792 true 0.5,0.333 0.583,0.333 0.583,0.333 0.917,0.74 true 0.167,2.667 0.333,2.833 0.167,0.167 10 true *1 0.208,3 0.375,3.167 0.167,0.167 10 true *2 1.333,0.438 1.5,0.604 0.167,0.167 10 false *a 0.771,0.063 0.938,0.229 0.167,0.167 10 false *b 0.292,0.25 0.458,0.417 0.167,0.167 10 false *c 1.979,0.958 2.146,1.125 0.167,0.167 10 false *d 1.979,0.073 2.146,0.24 0.167,0.167 10 false *e 0.604,1 0.938,1.167 0.333,0.167 10 false 45° 1.125,1 1.458,1.167 0.333,0.167 10 false 45°
*1 No. 1 Oil Cooler Inlet Hose
*2 No. 1 Oil Cooler Outlet Hose
*a Right Side of Vehicle
*b Upper Side of Vehicle
*c Paint Mark
*d 2 to 5 mm (0.0787 to 0.197 in.)
*e 0 to 3 mm (0 to 0.118 in.)


Install the No. 1 oil cooler inlet hose and No. 1 oil cooler outlet hose to the radiator assembly, and slide the 2 clips to secure the hose.

NOTICE:
·

Make sure to slide the No. 1 oil cooler inlet hose and No. 1 oil cooler outlet hose until each contacts the hose stopper of the radiator assembly.

·

Make sure that the claws of each clip are within the location shown in the illustration.




b.

Connect the hose clamp to the fan shroud.


c.
C410492C01
1.5,0.25 1.583,0.25 1.583,0.25 2,0.781 true 1.583,0.25 1.771,0.771 true 0.833,1.25 0.917,1.25 0.917,1.25 1.042,0.813 true 1.375,0.719 1.542,0.885 0.167,0.167 10 false *a 0.667,0.25 0.833,0.417 0.167,0.167 10 false *b 1.292,0.167 1.458,0.333 0.167,0.167 10 false *c 2.292,0.281 2.458,0.448 0.167,0.167 10 false *d 2.198,1.156 2.365,1.323 0.167,0.167 10 false *e 1.302,0.5 1.635,0.667 0.333,0.167 10 false 45° 0.625,1.167 0.792,1.333 0.167,0.167 10 false *c 1.292,1 1.625,1.167 0.333,0.167 10 false 45°
*a Right Side of Vehicle
*b Upper Side of Vehicle
*c Paint Mark
*d 2 to 5 mm (0.0787 to 0.197 in.)
*e 0 to 3 mm (0 to 0.118 in.)


Connect the No. 1 oil cooler inlet hose and No. 1 oil cooler outlet hose to the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube, and slide the 2 clips to secure the hose.

NOTICE:
·

Make sure to slide the No. 1 oil cooler inlet hose and No. 1 oil cooler outlet hose until each contacts the hose stopper of the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube.

·

Make sure to align the paint mark of the No. 1 oil cooler inlet hose and No. 1 oil cooler outlet hose with the paint mark of the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube.

·

Make sure that the claws of each clip are within the location shown in the illustration.




Hide 17410 3.INSTALL FRONT EXHAUST PIPE ASSEMBLY