Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2019.02–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0382589 ECD SYSTEM(w/ Urea SCR System) D

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  INITIALIZATION  


INITIALIZATION PROCEDURE FOR DIESEL THROTTLE BODY ASSEMBLY, ELECTRIC EGR CONTROL VALVE ASSEMBLY AND TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR


HINT:

When the diesel throttle body assembly, electric EGR control valve assembly or turbocharger nozzle vane control actuator is replaced, perform initialization.


a.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Turn the ignition switch to ON and wait for 10 seconds or more.



CATALYST DETERIORATION LEARNING VALUE AND DPF DEPOSITION VALUE CLEAR FUNCTION


HINT:

When the exhaust manifold converter sub-assembly (DPF catalyst) is replaced, the catalyst deterioration learning value and DPF deposition value stored in the ECM must be cleared.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the menu options in this order: Powertrain / Engine / Utility / Catalyst Deterioration Leaning Value Clear.

Powertrain > Engine > Utility
Tester Display
Catalyst Deterioration Learning Value Clear
50005 372 4568

e.

Press "Next".


f.

Press "Exit".


g.

Enter the menu options in this order: Powertrain / Engine / Utility / DPF Deposition Value Clear.

Powertrain > Engine > Utility
Tester Display
DPF Deposition Value Clear
50005 372 4574

h.

Press "Next".


i.

Press "Exit".



CRANK TIME COMPENSATION LEARNING VALUE CLEAR FUNCTION


·

This procedure uses the GTS to perform "Crank Time Compensation Learning Value Clear".

·

When replacing the timing rotor (engine assembly), perform "Crank Time Compensation Learning Value Clear".


HINT:
·
A204035

If an error occurs during compensation reset, check the vehicle condition, and then perform compensation reset again.

·

A communication malfunction may occur if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Crank Time Compensation Learning Value Clear.

Powertrain > Engine > Utility
Tester Display
Crank Time Compensation Learning Value Clear
50005 372 4571

e.
A280989

When the first screen is displayed, check the vehicle condition and push "Next".


f.
A280984

When the screen indicating reset completion is displayed, push "Exit".



A/F SENSOR LEARNING VALUE CLEAR FUNCTION


·

This procedure uses the GTS to perform "A/F Sensor Learning Value Clear".

·

When replacing the air fuel ratio sensor, replace the sensor and then perform "A/F Sensor Learning Value Clear".


HINT:
·
A204038

If an error occurs during compensation reset, check the vehicle condition, and then perform compensation reset again.

·

A communication malfunction may occur if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / A/F Sensor Learning Value Clear.

Powertrain > Engine > Utility
Tester Display
A/F Sensor Learning Value Clear
50005 372 4572

e.
A295533

When the first screen is displayed, check the vehicle condition and press "Next".


f.
A295534

When the screen indicating reset completion is displayed, press "Exit".