Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2019.02–2019.06
RM35X0E _53 Suspension _078885 TIRE PRESSURE MONITORING _0382739 TIRE PRESSURE WARNING SYSTEM M

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  REGISTRATION  


PROCEDURE

Hide 1. BEFORE REGISTRATION

NOTICE:
·

The transmitter ID is written on the tire pressure warning valve and transmitter. It is not possible to read the transmitter ID after installing the tire onto the wheel. Therefore, make a note of the transmitter ID before installing the tire.

·

Tire pressure warning ECU and receiver ID registration after replacement must be performed using the GTS.



a.

In case of tire pressure warning ECU and receiver replacement:

i.

Before replacing, use the GTS to read and record all of the current IDs and registered tires with transmitters (4 or 5 tires) of the tire pressure warning valve and transmitter registered to the tire pressure warning ECU and receiver.


ii.

If reading the stored transmitter IDs is impossible due to malfunctions of components such as the tire pressure warning ECU and receiver, remove the tires from the wheels and check the IDs located on the tire pressure warning valve and transmitters.



b.

In case of tire pressure warning valve and transmitter replacement:

i.

Take a note of the 7-digit number (transmitter ID) written on the tire pressure warning valve and transmitter.

C413296C01
5.156,1.083 5.823,0.469 5.823,0.469 5.958,0.469 true 0.479,0.292 0.792,0.49 0.313,0.198 10 false *1 6.042,0.375 6.354,0.573 0.313,0.198 10 false *a
*1 Tire Pressure Warning Valve and Transmitter - -
*a Transmitter ID (7-digit Number) - -




Hide 2.REGISTER TRANSMITTER ID

HINT:
·

The previously registered IDs will be cleared from memory when the registration is completed.

·

If the ID registration step is not completed within 300 seconds, ID registration will be canceled.



a.

Set the tire pressure to the specified value.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Utility / ID Registration/Tire Number Registration.


f.

Perform the procedure displayed on the GTS.

HINT:

The number of tires with transmitters can be changed to 4 wheels only when the default value is set to 5 wheels. The number of tires is changed only when there is a special request from the customer. Normally, the default value for the number of tires is set.



Hide 3. CONFIRMATION OF TRANSMITTER ID REGISTRATION

NOTICE:
·

It may take a few minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121 to C2125.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>C2121

·

If the transmitter IDs have not been registered, DTC C2171 is stored in the tire pressure warning ECU and receiver after 3 minutes or more.

·

If normal pressure values are displayed, the transmitter IDs have been registered correctly.

·

If the tire pressure values are not displayed after a few minutes, the transmitter IDs may be incorrect or the system may have a malfunction.

·

After all transmitter IDs are registered, DTC C2126 is stored in the tire pressure warning ECU and receiver and the tire pressure warning light blinks for 1 minute and then illuminates. When the tire pressure warning ECU and receiver successfully receives signals from all the transmitters whose IDs are stored in the ECU, DTC C2126 is cleared and the tire pressure warning light goes off.



a.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ID 1 Tire Inflation Pressure ID1 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 900 kPa (9.2 kgf/cm2, 131 psi), Relative pressure (Gauge) / 800 kPa (8.2 kgf/cm2, 116 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 2 Tire Inflation Pressure ID2 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 900 kPa (9.2 kgf/cm2, 131 psi), Relative pressure (Gauge) / 800 kPa (8.2 kgf/cm2, 116 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 3 Tire Inflation Pressure ID3 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 900 kPa (9.2 kgf/cm2, 131 psi), Relative pressure (Gauge) / 800 kPa (8.2 kgf/cm2, 116 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 4 Tire Inflation Pressure ID4 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 900 kPa (9.2 kgf/cm2, 131 psi), Relative pressure (Gauge) / 800 kPa (8.2 kgf/cm2, 116 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 5 Tire Inflation Pressure ID5 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 900 kPa (9.2 kgf/cm2, 131 psi), Relative pressure (Gauge) / 800 kPa (8.2 kgf/cm2, 116 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
HINT:
·

*: It may take a few minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121 to C2125.

·

The wheel position cannot be determined from ID1 through ID4 or ID1 through ID5 on the Data List.



Chassis > Tire Pressure Monitor > Data List
Tester Display
ID 1 Tire Inflation Pressure
ID 2 Tire Inflation Pressure
ID 3 Tire Inflation Pressure
ID 4 Tire Inflation Pressure
ID 5 Tire Inflation Pressure
50003 203 36,37,38,39,40

b.

Reduce the tire inflation pressure of each tire 40 kPa (0.4 kgf/cm2, 5.8 psi) or more, and check that the "ID Tire Inflation Pressure" data is updated and that the actual tire inflation pressures are displayed.


c.

After confirming that all of the tire inflation pressure values have been updated, adjust the tire inflation pressure to the specified value, press the tire pressure warning reset switch and perform initialization.