Home › Drivetrain › RC60J (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION SYSTEM (for 7GR-FKS)
RM35X0E _52 Drivetrain _078740 RC60J MANUAL TRANSMISSION / TRANSAXLE _0383349 MANUAL TRANSMISSION SYSTEM(for 7GR-FKS) D

RC60J MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION SYSTEM(for 7GR-FKS)  INITIALIZATION  


IMT INSTALLATION INFORMATION RESET (WITH IMT SWITCH)


This function is used to reset the iMT installation information stored in ECM.

NOTICE:

Performing iMT Installation Information Reset will clear the stored status of the iMT installation information (iMT Type). Make sure to perform iMT Installation Information Reset and set the iMT installation information (iMT Type) when replacing any of the parts shown in the following table.

Replaced Part
ECM


HINT:

Use this function to reset the iMT installation information when the sensor is wrongly assembled or the ECM is wrongly interchanged between a vehicle with iMT and a vehicle without iMT.


a.

Perform iMT Installation Information Reset as follows:

i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



iv.

Turn the GTS on.


v.

Enter the following menus: Powertrain / Transmission / Utility / iMT Installation Information Reset.

Powertrain > Transmission > Utility
Tester Display
iMT Installation Information Reset
50005 373 8005

vi.

Perform the iMT Installation Information Reset.



b.

Set the iMT installation information as follows:

i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Fully depress the clutch pedal.


vi.

Move the shift lever to neutral.


vii.

Start the engine.


viii.

Release the clutch pedal.


ix.

Fully depress the clutch pedal.


x.

Release the clutch pedal.


xi.

Wait at least 3 seconds.


xii.

Enter the following menus: Powertrain / Transmission / Data List / iMT Type.

Powertrain > Transmission > Data List
Tester Display
iMT Type
50003 373 931

xiii.

Confirm that the iMT Type is Type B (with iMT).



c.

After performing iMT Installation Information Reset, perform Road Test.

Click hereDrivetrain>RC60J (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSMISSION SYSTEM (for 7GR-FKS)>ROAD TEST



IMT INSTALLATION INFORMATION RESET (WITHOUT IMT SWITCH)


This function is used to reset the iMT installation information stored in ECM.

NOTICE:

Performing iMT Installation Information Reset will clear the stored status of the iMT installation information (iMT Type). Make sure to perform iMT Installation Information Reset and set the iMT installation information (iMT Type) when replacing any of the parts shown in the following table.

Replaced Part
ECM


HINT:

Use this function to reset the iMT installation information when the sensor is wrongly assembled or the ECM is wrongly switched between a vehicle with iMT and a vehicle without iMT.


a.

Perform iMT Installation Information Reset as follows:

i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



iv.

Turn the GTS on.


v.

Enter the following menus: Powertrain / Transmission / Utility / iMT Installation Information Reset.

Powertrain > Transmission > Utility
Tester Display
iMT Installation Information Reset
50005 373 8005

vi.

Perform the iMT Installation Information Reset.


vii.

Enter the following menus: Powertrain / Transmission / Data List / iMT Type.

Powertrain > Transmission > Data List
Tester Display
iMT Type
50003 373 931

viii.

Confirm that the iMT Type is Type A (without iMT).