DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled | Total distance traveled | Min.: 0
Max.: 16777215 |
- | - |
| Total Distance Traveled - Unit | Unit for total distance traveled | km or mile | - | - |
| Starter SW | Starter signal | ON or OFF | ·
ON: Starter operating ·
OFF: Starter not operating |
- |
| Clutch SW | Clutch switch status | ON or OFF | ON: Clutch pedal depressed | When this item displays "OFF" with the clutch pedal depressed, the shock when accelerating and decelerating the vehicle becomes larger and pilot quality learning cannot be performed.
Symptoms when out of range: The cruise control, pilot quantity learning, etc. may not function properly or may not function at all. |
| Stop Light SW | Stop light switch status | ON or OFF | ·
ON: Brake pedal depressed ·
OFF: Brake pedal released |
- |
| Cruise Main SW | Cruise control switch status | ON or OFF | - | - |
| NIM Sensor Speed | Input shaft speed (NIM) | Min.: 0 rpm
Max.: 16383 rpm |
Input shaft speed (NIM) equal to engine speed (NE): Clutch pedal not depressed, vehicle running | - |
| NIM Sensor Voltage | Input shaft speed sensor (NIM) output voltage | Min.: 0.000 V
Max.: 4.999 V |
0.1 to 1.9 V: Clutch pedal not depressed, engine idling | - |
| Clutch Stroke Position | Clutch pedal stroke calculated by ECM | Min.: -200%
Max.: 199.9% |
Value increases: Clutch pedal released → clutch pedal fully depressed | - |
| Clutch Stroke Sensor Voltage | Clutch pedal stroke sensor assembly output voltage | Min.: 0.000 V
Max.: 4.999 V |
Value increases: Clutch pedal released → clutch pedal fully depressed | - |
| iMT SW | iMT switch status | ON or OFF | ·
ON: iMT switch being pressed and held ·
OFF: iMT switch not pressed |
- |
| iMT Telltale | iMT telltale display request | OFF, Green or Yellow | ·
OFF: iMT system off ·
Green: iMT system stand-by ·
Yellow: iMT system malfunction, indicator light initial check |
- |
| iMT Type | iMT installation information | Type A or Type B | Type B: Installation judgment finished | ·
Type B: w/ iMT switch ·
Type A: w/o iMT switch |
Enter the following menus: Powertrain / Engine / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed | Vehicle speed | Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph) |
Actual vehicle speed | ·
This is the current vehicle speed. ·
The vehicle speed is detected using the wheel speed sensors. ·
Vehicle speed data is delayed when it is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped. |
| Engine Speed | Engine speed | Min.: 0 rpm
Max.: 16383 rpm |
550 to 700 rpm: Idling (shift lever in neutral, engine warmed up and A/C off) | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |